Search Documents

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"Abstract: In this work, low temperature carbothermic reduction of Panzhihua low grade ilmenite after ball milling were investigated. The ball milling of ilmenite and graphite were processed in a ball mill. The milling process can attenuate the particle of ilmenite, and the ilmenite characteristic peak were broadened and weakened. The reduction temperature and behaviors are studied on the thermo gravimetric apparatus; lower temperature and higher reaction rate were obtained for the reduction of ilmenite with graphite after milled. The reduction temperature and times of ilmenite decreased to 1000-1025°C and 40-60min via milled for 4 or 8h; Low down the reduction temperature can eliminate the solution of Mg2+ and FeTi03 in a certain degree; the reduced ilmenite has an obvious loose structure, can favored the subsequent procedure such as leaching.1 IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposited in Panzhihua, China. In this reserve, there is about 8.73x108 t ofTi02, Accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [JJ Titanium mineral deposits major classified into Rock type and Placer type. Rock type is the igneous mineral, which have great content of FeO (Relative to Fe20 3) and gangue. The rock textures are compact and almost are complex ore. Rock type Titanium mineral major are ilmenite and titan magnetite ore, difficult to separate the metal ore and gangue. l.21 Thus, the Ti02 grade of Rock type ilmenite much lower than the Placer type (Table land 11). Panzhihua ilmenite are the typical Rock-type, due to the higher contents of MgO, CaO and Si02 and the complex mineralogy in ilmenite in Panzhihua region, making its direct reduction progressively more difficult. Mechanical activation, usually carried out by energetic milling or ball milling, was reported to significantly decreased the reduction temperature and accelerate the reaction rate of reduction of ilmenite with carbon, silicon and Magnesium. f3·(>J It reported that the process temperature were decreased to 600-1000°C and the annealing time were reduced to 30-120min after milled for 50-400 h. Shorter milling time involved was imported for else procedure such as direct leaching. 171 Hardly any research had referred to the carbothermic reduction reactivity of ilmeite milled for a short time as 1-1 Oh. In the present work, the aim is to investigate the reactivity and reaction temperature of carbothermic reduction of Panzhihua ilmenite. The Phase composition and micro morphology of samples are characterized."

Jan 1, 2011

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By Huimin Lu, Shi Zhou, Lisha Yang

"The Zeolitic imidazolate frameworks (ZIFs) were successfully synthesized by applying a combination of ionothermal synthesis and microwave energies for rapid synthesis. The synthesis was proceeded under various conditions including different raw materials, reaction temperature as well as microwave irradiation time. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are new type of porous materials formed by inerratic polyhedral in three-dimensional. They are the ideal crystalline substances for gas separation and storage. The assynthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and C02 adsorption test. Results illustrated that the synthesized samples had stable structure, high thermal stability (up to 530 °C) and C02 adsorption capacity (10.2 cm3/g at 0°C under ambient pressure). This novel method also showed great advantage with high energy efficiency, safe synthesis conditions, and rapid crystallization time (60 minutes).IntroductionNowadays, carbon dioxide capture has become imperative due to the global warming caused by the increase of C02 in the atmosphere, especially produced by the concentrated sources such as power plants [1]. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are ideal crystalline substances for gas separation and storage due to their structure diversity, high thermal and chemical stability [2-5]. They are formed by inerratic polyhedra in threedimensional with large cages and small apertures. Traditionally, ZIFs are synthesized by solvothermal method in a sealed autoclave under autogenous pressure [6-9]. However, in order to generate the products, the solvothermal temperature should not be lower than 100°C according to the sovlothermal mechanism. Moreover, at such a temperature, molecules with a low boiling point (such as water) may generate high pressure in reactor which might cause danger [9]. Thus the synthesis requires the equipment to possess resistance to autogenous pressure and corrosion. Further, conventional solvothermal methods need a long time to prepare products, usually a few days, which is a large energy consumption and inefficiency. So it is interesting to synthesis ZIFs through other ways under mild reaction condition with high energy efficiency."

Jan 1, 2012

By N. Y. Ma

Solid wastes produced in ironmaking and steelmaking off-gas cleaning systems often contain zinc. The zinc level in these solid wastes is generally too high to recycle the wastes for iron through blast furnaces, but too low to economically treat the wastes for zinc through zincrecovery facilities. The behavior, status, and distribution of zinc in the ironmaking and steelmaking off-gas cleaning systems have been analyzed from three aspects: thermodynamics of zinc condensation, oxidation and deposition, correlation of zinc concentration with particle size and density, and aerodynamics of dust particles in the off-gas cleaning systems. Theory and supporting data show that spontaneous separation of zinc from iron-bearing dust occurs in the ironmaking and steelmaking off-gas cleaning systems. Dry off-gas cleaning systems provide the most favorable conditions and environments for zinc to separate from the dust. If highefficiency dry separators were applied and appropriately arranged in the off-gas cleaning systems, zinc would be concentrated, and the majority of the solid wastes could be recycled for iron recovery through blast furnaces.

Jan 1, 2008

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By H. C. Roland Kammel

Stannous sulfate electrolytes are widely used nowadays in electrolytic tin production. Characteristic features of this electrolysis process are that dense cathode deposits can only be obtained by additions of organic additives and that so called ?black mud is formed on the anode surface which leads to an increase in cell-voltage. In order to prevent excessive cell-voltages or oxygen evolution the black mud has to be removed periodically. Studies in laboratory scale have been performed about the effect of different organic additives on electrolytic tin deposition and the formation of surface layers on pure and industrial tin anodes. Results reveal that organic addition agents are effective in reducing cathode roughening as well as extending the covering time of the anode ?by black muds.

Jan 1, 1985

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By Zhenglong Li

A process has been developed to recover titanium from a blast-furnace slag which contains about 20-25% Ti02 and 12% Fe. In this process. "hot" slag from the blast furnace is directed to a separate furnace where it is reheated with additives to form two simple slag phases: one is titanium enriched anosovite (Ti3O5) and the other is a titanium lean non-crystal glass phase. The modified slag is then processed by conventional beneficiation techniques to produce a marketable titanium concentrate and a usable slag material. This paper focus on separating anosovite from glass by electrostatic separation and froth flotation.

Jan 1, 1996

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30tlhour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By L. A. Harris

In the present study the open gradient magnetic separation' (OGMS) method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy (SEM) and x-ray diffractometry (XRD) were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (-80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

Jan 1, 1981

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991