Search Documents

By P. Blazy

A hydrometallurgical procedure for the recovery of metal from ore, particularly of copper from sulphide materials is described. In the course of this procedure, the raw material is first of all submitted to the action of an appropriate reducing system and then treated with a ferric salt solution which brings about the selective solubilisation of the elements to be recovered with respect to those constituting the pyritic phase. This procedure is investigated using two ore samples proceeding from massive sulphide deposits, presenting different chemical and mine- ralogical characteristics. The results of this investigation are compared with those obtained by a classical process employing a ferric salt solution. It appears that one solubilisation of copper takes place under particularly advantageous conditions when our procedure is used. The principal parameters affecting leaching of zinc, lead and copper are examined. The selectivity of this treatment is evaluated by following the change during the treatment in the pyritic phase.

Jan 1, 1976

By S. P. Vanka, B. G. Thomas, S. Sivaramakrishnan

"During the continuous casting of steel, transient 'flow events can be very important to the generation of quality problems, such as shear entrainment, surface level fluctuations and bubble entrainment. These phenomena can be better predicted using Large Eddy Simulation (LES) models than the K-E models, which have been extensively studied. In this work the turbulent transient flow in a water model of a continuous caster has been both simulated using LES models and measured using Particle Image Velocimetry (PIV). The results of PIV and LES have been compared to validate the LES model and also to enhance the understanding of the prominent transient features of the flow field. The flow near the top surface in PIV was found to contain periods of 5-1 Os when the velocities were three to four times their mean values, which is of importance to the shear entrainment of the liquid flux. In both simulation and PIV the upper roll structure is found to change chaotically from a single large recirculation structure to a set of distinct vortices. The inlet swirl in PIV is seen to persist more than halfway across the mold, causing a characteristic staircase velocity vector pattern when viewed in a plane parallel to the wide faces. The lower rolls in PIV are significantly asymmetric for very long periods of time (- I-hour) and go through a repeating sequence of features. One of these features involving a short circuit between the upward and downward flow in the lower roll is also seen in the simulation and is of significance to bubble entrapment.IntroductionThe turbulent flow through the nozzle and in the mold of the continuous caster has been studied extensively using computational Reynolds Averaged Navier Stokes (RANS) models of turbulent flow [1,2]. Defects, such as internal inclusion of liquid fl4x through surface shear, pencil pipe defects due to bubble entrapment, surface defects due to level fluctuations are caused by transient flow phenomena oc'curring in the mold. These phenomena can be better predicted using transient Large Eddy Simulation [3] or ""LES"" models."

Jan 1, 2000

By B. A. Paponetti

The following report discusses the bioleaching of chalcopyrite of italian origin catalyzed by Thiobacillus ferrooxidans. The developments vcr.ius time of the main .biochemical and chemical reactions involved in the production of soiuble and insoluble species were investigated focusing on the times at which they begin and bow long they last. The precipitates were characterized both in quantity and in quality relating the rate of the process to the precipitates fonnatiom. A material. balance has been made to verify the proposed mechanism.

Jan 1, 1991

By L. Katgerman, H. J. Brinkman, J. Duszczyk

"The phase formation sequence in the in-situ synthesis ofTiB2 in A1 from elemental A1, Ti and B powders is identified with a combination of DSC and XRD. After the melting of A1, A1B2 and A13 Ti are formed at the contact areas between A1-B and A1-Ti. The influence of variations in starting composition on the reaction kinetics is explained in terms of there effect on the different processes in the formation sequence. Parameters in the starting composition that were investigated are; fraction ofTiB2 forming reactants, non stoichiometric Ti:2B ratio's, and addition of alloying element Cu.It was found that a liquid Al phase is necessary for the in-situ TiB2 forming reaction from the intermediate A1B2 and A13 Ti phases. If all Al is consumed by the formation of A1B2 and A13 Ti the TiB2 formation is halted until the decomposition of A1B2 and A13 Ti .Overstoichiometric amounts of B are needed for complete conversion of the Ti, present in A13Ti, into TiB2 This is explained by the fact that some of the stable A1B12 phase is formed after the decomposition of A1B2•The addition of Cu leads to an increasing reaction rate in the A1-Ti reaction. A possible explanation for this is that the A1-Cu liquid penetrates more easily between the Ti and its surface oxide than the unalloyed A1 liquid."

Jan 1, 1998

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K. A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in the Fe-Pb-C system are 95.4%Fe-4.5%C-0.1 %Pb and 99.9%Pb-0.I%Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx [mass%X in molten Pb]/(mass%X in molten Fe), are 2.2, 2.2 and 1.4, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By M. Kobayashi, Y. Nishisu

"Fine multicomponent particles of yttrium and europium were synthesized through the precipitation from homogeneous solution, and the various characteristics related with the fluorescence were investigated. The morphology and the fluorescent characteristics of the synthesized particles were affected by ionic species in the stock solution. In the presence of sulfate ion, some parts of the precipitated particles were aggregated, and _the fluorescent characteristics were not good. On the other hand, in the presence of chloride ion or nitrate ion, the particles precipitated were almost monodispersed, and, the intensity of the fluorescent emission were strong after calcination. Further, these particles were also very attractive as the red phosphor in the mercury-free fluorescent systems.Introduction Eu doped Y oxide particles have been widely investigated for the application to the fluorescent lamps and displays: Recently, the fluorescent lamps are pointed as harmful electric equipments because of using mercury for excitation. Therefore, the use of the mercury in the fluorescent- system will be limited or prohibited worldwide in near future. Then, the development of the mercury-free fluorescent lamp is strongly required without delay. Inert gas such as neon and/or xenon seem to be applicable as new excitation element that replaces the mercury. However, in case xenon the excitation wavelength,' 146 and 172nm, is different from that of the mercury, 254nm, and then, the commercial phosphors which are used in the present fluorescent lamp system are not available. Therefore, the invention of the novel phosphors is essential for the development of the mercury-free fluorescent lamp. Further, the controls of the size and shape of the particles precipitated are also important, because the homogeneity of the size and the shape is very important for the fabrication of the layer of the phosphor particles. That is to say, the development of the phosphor particles with controlled components, size and shape is essential. The precise control of size and shape improves the packing density, and so, the screen performance of the lamp [1]. In addition, these phosphor particles should be also useful for the application of the flat-plane displays, for example, PDP, etc. [2,3]. In the present work, first, the particles including yttrium and europium for the precursor for red phosphor were prepared through precipitation from homogeneous solution. This process was precisely controlled for the control of the components, size and shape of the particles precipitated. Next, the particles precipitated were calcined, and then, their fluorescent properties were characterized. As a result, some of them showed the possibly available characteristics as the red phosphor for mercury-free fluorescent lamp system. These experimental results are presented in this paper."

Jan 1, 2000

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the 'solvent' or 'transport agent' and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995

By F. H. Froes, O. N. Senkov, N. Srisukhumbowornchai

"Mechanical alloying (MA) and thermohydrogen processing (THP) approaches were used to synthesize amorphous or nanocrystalline powders of the titanium-aluminide-based alloys and composites. Fully dense samples with nanocrystalline and bimodal structures were produced from these powders by hot isostatic pressing. The stability of the microstructures during continuous heating at high temperatures was studied. Characterization techniques including X-ray diffraction, scanning and transmission electron microscopy, energy dispersive spectroscopy, and differential thermal analysis were used in this work.IntroductionAs performance demands increase, so do the demands for enhanced mechanical property combinations at reduced overall weight; and reduced weight can most efficiently be realized by the use of low-density metals with high specific strength, such as titanium alloys and titanium-aluminum intermetallics [l]. The TiAl-based alloys are attractive for high temperature applications, however, they exhibit poor ambient temperature ductility and fracture toughness [2-4]. Incremental improvements can be obtained using ingot metallurgy processing [1,2] but more substantial developments require ""far from equilibrium"" (FFE) synthesis [5-8] which allows development of novel constitutional and microstructural effects, leading to enhanced physical and mechanical properties. Improved ductility of titanium aluminide intermetallics can be achieved by disordering, grain refinement and deoxidation of the matrix, while good elevated temperature properties are achieved due to a dispersion of fine, thermodynamically stable, second phase particles.The approaches for producing nanocrystalline and amorphous TiAl-based alloys and composites used in this work included FFE powder metallurgy techniques such as rapid solidification, mechanical alloying and thermohydrogen processing. The rapid solidification (RS) technique allows extension of solubility limits, production of novel phases, and much more refined microstructures (down to nanostructure or even amorphous range) than is possible using the ingot metallurgy technique [9]. Mechanical alloying (MA) is a process in which heavy working of powder particles results in intimate alloying by repeated deformation, fracturing and welding. This process can produce greater departure from FFE than RS, leading to greater refinement effects; and additionally allows production of a dispersion of second phase particles [10]. Thermohydrogen processing involves hydrogen as a temporary alloying element in titanium to facilitate processes, refine microstructure, and improve final mechanical properties [11]; it was used in the present work to improve MA process. The combination of these three processes was expected to control the final microstructure even better than either process used alone."

Jan 1, 1998

By Maria Salazar-Villalpando, Todd H. Gardner

"Efficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). Hexaaluminate catalysts prepared at NETL may represent a product that can be utilized for the conversion of CO2 to syn-gas. In this work, transition metals dispersed in barium hexaaluminate have shown to be promising new catalysts for dry methane reforming. In this investigation, a series of BaNixAl12-yO19-d catalysts with varying Ni content were prepared by co-precipitation followed by calcination at 1400°C. CO2 reduction by dry methane reforming was carried out to determine catalyst performance as a function of temperature and carbon formation was also quantified after the reforming tests. Results of catalysts characterization, dispersion and surface area, were correlated to catalytic performance.IntroductionEfficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). The dry reforming reaction has been known for a long time. Recent publications have reported studies over several catalysts. For example, the CO2 reforming of CH4 over mesoporous nanocrystalline zirconium powders (ZrO2–3%M2Ox; M: Ce, La and K) at 700ºC have shown methane conversion up to 60% (1). Similarly, the effect of Ni content (1–12 wt%) on the surface and catalytic behavior of bimetallic PtNi catalysts supported on ZSM-5 for reforming of methane with CO2 has been studied and report shows a maximum conversion of 16% and catalyst deactivation was observed during the first hour of time on stream (2). In another report, (3) Ni/a-Al2O3 catalyst was tested for syn-gas generation at 750ºC. The maximum methane conversion was 25%."

Jan 1, 2008

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia's demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia's titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By Xiaobing Yang, Abhishek Lahiri, Animesh Jha

"In the FFC-Cambridge process, the cathodic dissociation of oxide and CO/CO2 production on carbon anode is the basis for metal production in a CaCl2 bath. By using an inert intermetallic anode, the CO2 evolution can be eliminated altogether with acceleration in the electro-reduction kinetics. At present the process suffers from slow reduction kinetics of TiO2 to Ti metal, which can be enhanced significantly by the incorporation of alkali species in the TiO2 pellet at the cathode and in the CaCl2 bath in the presence of an intermetallic inert anode. Nearly full metallization with greater than 99% of Ti metal containing 1500 ppm of oxygen is possible to achieve in less than 16 hours of electro-reduction. Analyses of phase composition and the microstructures morphology in fully metallized pellets revealed the presence of localized solidified Ti layer, indicating that fast reduction process also involved formation of liquid phase as middle stage reaction. In addition, in situ creation of porosity and maintain higher current level during electrolysis process were two key factors to fully reduction of TiO2.IntroductionDuring cathodic dissociation of TiO2 in a CaCl2 bath and anodic evolution of CO2 on a carbon anode, which is the basis for the FFC Cambridge process [1], the rate of metallization slows down due to the formation of CaTiO3 at the reaction interface. Calcium and alkaline earth perovskites are known for their poor electrical conductivity which adversely affects the overall electro-reduction. One of the ways to increase the porosity is via the addition of polyethylene precursors in the pellet or by directly starting from perovskite [2, 3]. The experimental evidences shown in the literature confirm although the speed of reaction increases, but a complete or near complete metallization is not possible by enhancing the in-situ porosity alone, as the insulating perovskite is very slow to decompose under the equilibrium that prevails in the cell. Plethoric evidences on carbon anode show with the current decrease gradually, and finally stabilize at a very low value between 0.2 and 0.4 A, which is a testimony of the presence of perovskite insulating barrier in the current path. Our aim in this paper is to demonstrate the mechanism of enhanced electro-reduction when alkali ions are present in the oxide pellet at cathode and in the bath. We also show for the first time the use of an intermetallic anode for Ti-metal production using the FFC Cambridge process."

Jan 1, 2009

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires 'a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill. During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003