Search Documents

By Xiang-dong XING, Zhen-yang wang, Jian-Liang Zhang

Distribution behavior of titanium between CaO-SiO2-MgO-Al2O3-TiO2 and hot metal was studied between 1350 °C to 1600 °C. Experimental results indicate that the reaction temperature influenced the activity coefficients of titanium and resulted in the variation of equilibrium constant. Finally, the Gibbs free energy formula of titanium carbothermic reduction was fit out using the thermodynamic model of Wagner and congregated electron phase models.

Jan 1, 2015

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By G. Lissens

In this work the electrochemical combustion of dissolved organic species in a single compartment cell containing a titanium mesh cathode and a boron doped diamond anode has been studied, The organic molecules involved were complexing agents such as EDTA (ethylenediaminetetraacetic acid) or NTA (nitrilotriacetic acid) used in metal plating shops and bright nickel plating bath additives, From batch experiments, it is shown that complete decomplexing of EDTA and NIA is feasible. Complete TOC (Total Organic Carbon) removal from solutions containing 0.01 M EDTA, 0.02 M NTA and bright nickel plating bath additives could also be achieved. Recycling experiments show that decomplexing of EDTA and NTA solutions can be obtained at an average electrical energy input of ~20kWh.kg-1 of complexing agent. Decomplexing rates of respectively 3.l3 mmol.Ah-1 for EDTA and NTA have been obtained, The Instantaneous Current Efficiency (ICE) was 71% for EDTA and 95% by NTA, Simultaneous recovery of Cu from a 0.01 M Cu-EDTA solution has also been evaluated. A solution (1.8 dm3) containing 0.01 M EDTA and 528 ppm of Cu was treated in a single compartment cell at a current density of 2 A.dm-2. 73% of the TOC could be removed and a final copper concentration of 8 ppm was obtained.

Jan 1, 2003

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By William Petruk

The mineralogy of the primary and oxidized ores from the Malanjkhand porphyry copper deposit in India was studied to determine ore characteristics that affect metallurgy, and to assess applicable processes for recovering the copper. Three mineral assemblages were found. One occurs in primary ore, another in moderately oxidized ore, and a thir:d in intensely oxidized ore. Chalcopyrite, the main mineral in the primary ore, is relatively coarse-grained, with grain size increasing as the ore grade increases. High chalcopyrite liberations should be achieved at a relatively coarse grind, and good chalcopyrite recoveries should be obtained. The chalcopyrite, however, tarnishes readily and oXidizes to chalcocite in a relatively short time (several months). The presence of both the tarnished chalcopyrite and chalcocite may affect chalcopyrite flotation and reduce copper recoveries, The moderately oxidized ore occurs in an oxidized cap immediately above the primary ore, and stockpiled primary ore alters quickly to a moderately oxidized ore. Chalcocite is a major copper-bearing mineral in moderately OXidized ore. The concentrator processing this ore should be capable of handling a chalcocite-rich ore. The intensely OXidized ore contains a wide variety of acid-soluble copper-bearing minerals. Leaching may be required to recover the copper from them.

Jan 1, 1987

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By Chunyang Guan, Jilai Xue, Zengjie Wang, Qiaochu Liu

Molten salts electrolysis method to prepare Al-RE alloys has attracted increasing attention recently. CaCl2 and Na3AlF6 were the most often used melts for this purpose. In this work, Al-Sc alloys prepared by electrolytic deposition process in both CaCl2 and Na3AlF6 melts were investigated, respectively. It was found that Sc distributes almost uniformly and Sc contents increase with increasing current intensity in both melts. Current efficiency was measured for comparison among various current densities applied. The alloy products were analyzed using XRD and SEM, where the formation behaviors of Al-Sc intermetallics were investigated in details. The experimental and theoretical results demonstrate that Al3Sc and Al0.968Sc0.032 are the major precipitates in the Al-Sc alloys prepared by molten electrolysis. The results are useful for selection and optimization of the molten salts compositions and the parameters of electrolysis operation.

Jan 1, 2015

By Joachim Ulrich

The spreading and splashing behaviour of single tin, lead, copper, aluminium and steel droplets impacting on a solid surface were experimentally examined. The droplet impact was observed using a high speed video imaging technique. The onset of splashing and the mass of the secondary droplets of impacting tin and lead droplets was quantified by the weight difference of the droplets before melting and the splat after the impact. The spread factor and the mass of the secondary droplets in dependence of the impact velocity is shown for different droplet materials, initial droplet diameters, target temperatures in ambient air and inert gas atmosphere. An empirical found correlation predicting the transition from spreading to splashing is presented by means of dimensionless numbers.

Jan 1, 1999

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999

By Chris Doyle

From 1997-2000. PT INCO undertook the Fourth Line Expansion Project (FLEX) to increase annual production rates from 90-100 to 150 Mlbs Ni/year (68,000 MT Ni/yr). In 2003, PT INCO nickel production underwent a major sustainable step jump that finally exceeded the targeted rate. This paper presents the changes that led to this achievement. The focus of mining changed. Improving Ni grade was important but only if electric furnace feed met target chemistry so that on-specification slag could be produced. The intensity of diamond core drilling for exploration was dramatically upgraded, mine planning strategy was totally re- vamped and an ore chemistry quality assurance team was formed. In the processing plant, measurement systems were upgraded for better control. Teamwork between sections vastly improved. The final step jump in production occurred when the fifth hydro-electric power generator was added to the furnace grid to allow the power-starved furnaces to cruise in operation at 70+ MW. Keywords: Free cash flow, Ore Chemistry, Measure, Control, Improve

Jan 1, 2004

By Fathi Habashi

During the recovery of copper, nickel, zinc, and lead from their sulfide ores, large amounts of sulfur dioxide are generated. A fraction of this gas is captured and transformed into sulfuric acid and liquid SOl and the remainder is emitted to the atmosphere. Numerous proposals were made to solve this problem. Hydrometallurgy offers the only valid solution by which elemental sulfur instead of sulfur dioxide can be produced. Sulfur can be easily stored, transported long distances, or transformed into S02 and H2S04 when desired.

Jan 1, 1996

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998

By L. Filip

The roast-leach-electrowinning (RLE) process for zinc was modified to treat two typical complex concentrates containing zinc, lead, copper, gold and silver. Laboratory testwork results indicated that the optimum roasting temperature ranged from 700 to 800°C, in order to produce acceptable residual sulfur levels. The calcined concentrate was subjected to a three-stage leach sequence. The resulting leach solution was purified by hematitic precipitation and directed to the recovery of copper and zinc by solvent extraction and electrolysis. Alkaline smelting and subsequent electrolytic purification recovered the lead and precious metals from the leach residue. A flowsheet was developed based on the laboratory testwork results, and demonstrated in a large-scale pilot plant. The recoveries produced during the pilot plant operation ranged from 90 to 92% for zinc and copper, 85% for lead and 90% for gold and silver, respectively.

Jan 1, 1999