Search Documents

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203' Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salmine

ChemSheet is a thermodynamic multi‐phase multi‐component simulation software, which is used as an Add‐in in Microsoft Excel. In ChemSheet, the unique Constrained Gibbs free energy method can be used to include dynamic constraints and reaction rates of kinetically slow reactions, yet retaining full consistency of the multiphase thermodynamic model. With appropriate data, ChemSheet models can be used to simulate reactors and processes in all fields of thermochemistry. The presentation will cover off‐line modeling of Cu‐flash smelters and advanced thermochemical simulation coupled with on‐line process control of Cu‐Ni smelting. The presentation will describe an off‐line model of Cu‐smelter based on critically assessed properties of the Al-Ca-Cu-Fe-O-S-Si –system (slag, matte and liquid metal) by using the quasichemical model. A four‐stage reactor model (shaft, settler, uptake and bath) is used for optimizing process parameters and feed particle distribution. As a second example, an advanced thermochemical model of a Ni-Cu sulphide smelting plant will be given. The on‐line model covers the operation of treating Ni-Cu-S concentrate via roasters, electric furnace and converters, producing a high grade Bessemer matte product for further refining. The model integrates the thermochemistry of the roasters and electric furnace, and predicts important process parameters such as degree of sulphur elimination in the fluid‐bed roasters, matte grade, iron metallization, slag losses and the iron to silica ratio in the electric furnace slag. Both models can be used to assist process engineers and operators in calculating the addition rates of coke, flux and air for different feed scenarios.

Jan 1, 2014

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By S. E. James

EAF dust has been listed as a "hazardous waste" due to the presence of lead and cadmium, and at times chromium. The 550,00 tpy production of . .EA]' dust, estimated for the United States alone, contains more than 10,000 tpy of lead and about 250 tpy of cadmium in addition to nearly 1'00,000 tpy zinc. Even though the listing of .EAF dust as a hazardous material stimulated extractive metallurgical work worldwide, process development efforts have focused only on the recycle of the potentially-valuable zinc units. However, the recycle of the lead and cadmium, while not lucrative, is the more critical effort. Horsehead Resource Development Company, Inc. (HRD), in conjunction with its sister company, Zinc Corporation of America (ZCA), has taken a unique approach to total recycle of the toxic heavy metals found in the EAF dust. Impure oxide, produced by either a Waelz kiln or FLAME REACTOR Process and containing the lead and cadmium, is calcined in a rotary kiln at Palmerton, Pennsylvania, to produce a refined zinc-rich intermediate for ZCA's electrothermic zinc plant at Monaca, Pennsylvania. During the calcining operation, lead and cadmium are concentrated in a fume product and shipped to ZCA's electrolytic plant at Bartlesville, Oklahoma. At Bartlesville, a new hydrometallurgical circuit has been constructed and the existing cadmium plant expanded. The combined facilities permit the total recovery of cadmium to refined metal and the lead to .a silver-rich intermediate, which is sold to lead smelters. In this paper the Waelzing, calcining and new leaching facilities will be described.

Jan 1, 1990

By P. Lussiez

Precipitates consisting of amorphous ferrihydrite and crystalline goethite have been prepared by aging hydrolyzed Fe (III) solutions at room temperature. The precipitates have been characterized by x-ray diffraction and differential thermal analysis. The amorphous ferrihydrite transforms to goethite with time. The ferrihydrite to goethite transformation is affected by the presence of small amounts of copper or nickel coprecipitated with the iron. .The addition of copper decreases the amount of goethite at a given aging time and increases the amount of coprecipitate which is initially dissolved in sulfuric acid, but it does not seem to affect the dissolution of the crystalline part'. It is proposed that adsorption of copper hydroxo species on goethite nuclei delays the ferrihydrite to goethite transformation. The effect of nickel is less dramatic than that of copper. Apparently a portion of the added nickel is adsorbed on the goethite crystallite surface rather than incorporated into the goethite lattice.

Jan 1, 1981

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By Carlos Maurício F. Vieira, Gabriel Oliveira Glória, Maycon Sidney Gomes de Camargo, Sergio Neves Monteiro, Fábio da Costa Garcia Filho, Maria Carolina Andrade Teixeira, Frederico M. Margem

The society is increasingly the concern about the ambiental impacts, and demand for eco-friendly materials. The composites reinforced with synthetic fibers are been replaced by composites reinforced with natural fibers because of the environmental advantages. Besides the environmental advantages, those fibers have economical and properties advantages, like the low density and cost. Composites with up to 30%of PALF fibers were tested. The analyzed parameters were the loss modulus, the storage modulus and the delta tangent. The test was conducted in the temperature interval from 25 to 195 °C in a DMA equipment operating at 1 Hz of frequency under a nitrogen flow. The results showed that the incorporation of continuous and aligned PALF fibers tends to increase the viscoelastic stiffness of the epoxy matrix. Contrasting this, minor changes occurred in both the glass transition temperature and the damping capacity of the structure as measured by the tan delta peaks.

Mar 1, 2018

By Baozhong Zhao

The direct smelting of copper concentrates to copper metal in a single furnace offers environmental and energy advantages over conventional two-stage copper smelting processes. However, the direct copper making results in unacceptably high level impurities (As, Sb and Bi) in the anode copper. Experimental studies have shown that it is possible to remove these impurities from molten copper by injection of sulfur-hexafluoride. This paper discusses the experimental findings on the influence of various factors on the rate of removal of impurities, such as the impurity inter-effects, initial oxygen content in the metal and injection rate of SF6.

Jan 1, 1995

By Eddie C. Chou

Phelps Dodge, Inc. (PD) is currently developing a lateritic nicke/Vcobalt deposit in Madagascar. Hazen Research, Inc. provides technical assistance to PD to investigate recovery processes for nickel and cobalt. Various process options were evaluated in laboratory experiments and pilot plant operations. The process selected for the feasibility study consists of feed preparation, high-pressure acid leach, countercurrent decantation wash, sulfide precipitation, sulfide dissolution, solvent extraction, ion exchange, and electrowinning. Among these unit processes, high-pressure acid leach, sulfide precipitation, and sulfide dissolution are applications of pressure technologies. Process development work and design criteria for commercial operations of these unit processes are presented in this paper. Concerns related to scaling in the high-pressure acid leach and the sulfide precipitation processes are discussed. Corrosion of various metal coupons under these environments was examined.

Jan 1, 2000

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By Bradley C. Bockrath

Some thirty coals were evaluated for liquefaction activity under a mixture of CO and H2 at 425° C. The viscosity of the liquid products was taken as an indicator of the degree of liquefaction. It was found that the direct liquefaction of a particular coal may be beneficially influenced by the presence of pyrite. Active pyrites are often found in the native mineral matter of the coal itself. For example, subbituminous and bituminous coals and lignites of relatively high pyrite content were found to liquefy more readily than similar coals or lignites which were poor in pyrite. The reactivity of inactive coals could be improved by using blends with active, pyrite-rich coals. In addition, pyrite was effective when added separately as pyrite concentrates obtained from coal beneficiation operations. Various other iron- and sulfur-bearing additives were also effective when used in combination as added slurry-phase catalysts, including iron oxides and mineral residues derived from liquefaction of active coals. Under liquefaction conditions, pyrrhotite ( Fe I- x5) is formed from pyrite or from the iron oxides and many sulfur containing species. Pyrrhotite was shown to be a hydrogenation/dehydrogenation catalyst for tetralin but is not active for initiating a variety of free radical reactions that do occur when pyrite is heated with tetralin. The role of pyrite in coal liquefaction is complex and still not well understood.

Jan 1, 1981

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By D. M. Fermino, C. G. Bastos Andrade, M. G. Fernandes, F. R. Valenzuela-Diaz

Treatments with high concentration solution of inorganic acid at temperatures under boiling point are a usual method for clay minerals structure modification. For many industrial uses bentonites must be cleared of impurities. In the present paper, a sample of Brazilian bentonite from Vitoria da Conquista, Bahia was modified by mild acid attack using hydrochloric acid under moderate conditions (90 °C, reaction times of 1, 6, 12, 18 and 24 h in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1 g/10 mL). The attacked samples were characterized by CEC, XRF, SEM, EDS and Stereomicroscopy. The purpose of these attacks is to reduce the concentration of impurities with minimal damage in clay minerals structure. The modified bentonite presented good results and tends to be a good economic and environmental alternative to manufacturing products with high added value such as polymer/clay nanocomposites, cosmetics and medicines.

Mar 1, 2017

By Edilson Marques Magalhães, Danielly Da Silva Quaresma, José Antônio da Silva Souza, João Nazareno Nonato Quaresma, Emanuel Negrão Macêdo

"The production of alumina from bauxite using the Bayer process generates the residue known by red mud. This material can be used as a source for concentration and recovery of valuable metals such as titanium. The greatest difficulty of concentrating titanium compounds is the large amount of iron oxide present in red mud > 30% by weight. This paper shows the extraction of the iron oxide, increasing the concentration of the titanium compounds. The red mud is leached with H2SO4 at 30% concentration and temperature range of 60°C, 80°C and 90°C. Analysis of the leached and concentrated was made to verify the effectiveness of the iron oxide extracting process and the titanium compounds concentration viability.2- IntroductionIn the state of Para is located the Industrial Unit Alumina of North of the Brazil S/A (Alunorte), created to produce and commercialize alumina, aluminum oxide, Al2O3. The ALUNORTE with Aluminum Brasileiro S/A (Albras) and Mining Rio do Norte S/A (MRN) complete the production cycle of aluminum in the state. Although the production of alumina has a importance great for the socio-economic status, as in any area other, generates a amount large of waste, thus causing environmental impacts. Pará State has produced 25 million tons of bauxite (Pinto, 2010), of which 60% were transformed into alumina plant in Pará and Maranhão by ALUNORTE by ALCOA, generating approximately 9,000,000 tons of waste known as Red Mud (RM). Due to the high reactivity this material is considered dangerous, and currently there is no operating process capable of reuse all the material produced at any refinery. The search for industrial processes in order to reuse these wastes can contribute to reducing the overall impact of the production process of alumina. In this context, this paper estudied, within the research line of Solid Waste valorization the mining industry and metallurgy, a process that makes possible the red mud as a source of raw material, in other words, seeks to maximize the use of red mud as raw material for concentration and or recovery of titanium compounds in both the crystalline form of anatase, rutile and ilmenite, avoiding the predatory extraction of natural resources of these materials. Applying definitely the concept of self-sustainability of the mining industry and metallurgy."

Jan 1, 2012