Search Documents

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By M. Wu, A. Kharicha, J. Bohacek, A. Ludwig

"During the horizontal spin casting of rolls, vibrations and mould deformations seems to have a significant effect on the final quality of the product. Sources for vibrations can be found in the poor roundness and a static imbalance of the chill itself. The bending of the mould axis is also considered. Both, vibrations and axis bending, are used as an input for CFD simulations of the flow dynamics of the liquid metal inside the rotating cylinder. The aim is to study the feedback of the free surface behavior in terms of wave propagation and various wave shapes. Introduction The horizontal spin casting process (HSC) is a casting process that has several advantages over the traditional gravity casting processes. Centrifugally cast products have a high degree of metallurgical purity and homogeneous microstructure. A significant gain is observed for the rupture strength, the rupture strain, and the Young modulus. These properties naturally depend on the centrifugal force and thus, the best mechanical properties can be found at the largest distance from axis of rotation. However proper selection of the angular frequency has to be done in order to prevent the so-called ""metal rain"" i.e. metal droplets can fall down from the upper part of the cylinder due to a too weak centrifugal acceleration. In the same time excessive speeds can lead to the appearance of longitudinal cracks caused by the hoop stress in the initially solidified layer. From empirical knowledge other parameters have important influence on the casting products, it includes the pouring temperature, the pouring rate, the mould coating etc. Recently the presence of natural or forced vibrations have been identified as possible additional factors to be taken into account [1-2]."

Jan 1, 2012

By Alexander V. Derevyanko, Victor P. Popov, Alexander I. Raitchenko

"If an electric current flows along some electroconductive suspension in columnar form the solid particles are 'experienced thermal, mechanical, and electromagnetic influences.The objects were suspension Sn (liquid) - Ni-Cr-Mo-W alloy (solid particles). This is refractory alloy on the Ni base. The direct constant current (with density -106 A/m2 ) flowed through the named suspension during 180+300 sec. At the beginning of experiments samples were ones containing particles suspended uniformly in volume. Although density of solid particles was ~9x103 kg/m3 , i. e. higher than density of liquid Sn (-6.8x103 kg/m3 ), after end of this processing, the non-uniform distribution of particles in volume of samples was observed: concentration of Ni-alloy particles in lower part was smaller than their concentration in upper part of samples, and simultaneously their concentration is increased near outer surface. There was probably the natural convection of Benard-Rayleigh type which had carried, so lid particles upwards, and, in same time, there was the action of spatial Lorentz-forces directed to center forcing the radial movement.The knowledge of named phenomena can be useful for elaboration of technology of gradient dispersed materials and development of some materials science fields.IntroductionThe liquid metal with the electric current or under the alternating magnetic field is experienced compression. This action causes the pressure within metal and the change of the surface of the metal column (see, for example, [1-4]). One of results of such an electromagnetic compression is extraction of the foreign solid particles from a cylindrical liquid sample to surface in the radial directions. However, more complicated paths of the inclusions are observed under some conditions of electric treatment."

Jan 1, 1999

By Marcel Sturzenegger

Though the extraction of copper is well established, generation of sulfur dioxide (S02) is still a troublesome issue. Conventional processes are further challenged by the increasing amount of impurities in the concentrates. Direct decomposition of the metal sulfides into the metal(s) and elemental sulfur under concentrated solar radiation offers a promising path to solve both problems. Thermogravimetric measurements under inert atmospheres have shown that synthetic chalcocite or chalcopyrite yield copper at temperatures as low as 1773 K. Even though optimum reaction temperatures might be somewhat higher, such temperatures are straightforwardly accessible in solar chemical reactors. The absence of oxygen will reduce the extent of slag forming reactions and thereby alter the evaporation characteristics of volatile impurities such as arsenic or antimony. Chemical equilibrium calculations for a chalcopyrite-enargite feed, e.g., have shown that under inert atmospheres arsenic compounds are completely evaporated at temperatures above 1000 K and an effective separation of arsenic from the matte is expected. An important step towards a solar production of copper is the design and testing of prototype solar chemical reactors for this reaction. Numerical modeling is a key tool supporting a rational design but it requires data of the high-temperature properties that prevail in these processes. Development of techniques for determining the essential quantities such as decomposition rates or radiative properties at temperatures up to 2000 K is therefore a main activity in our laboratory in order to control and optimize the process. Though developed in the frame of high-temperature solar technology, the experimental techniques are also suited to advance the understanding of conventional high-temperature processes. Keywords: Solar technology, Sulfur dioxide, Solar Radiation, Thermogravimetry, Chalcocite, Chalcopyrite, Numerical modeling.

Jan 1, 2003

By Alice Barreto Bevitori, Frederico Muylaert Margem, Noan Tonini SImonassi, Caroline Oliveyra, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The mechanical behavior and the fracture characteristics of composites with DGEB/TETA epoxy matrix reinforced with up to 30% in volume of continuous and aligned ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionSince the middle of last century, polymer composites have substitute many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffuess requirements that could be reached with synthetic fibers such as gloss, carbon and aramid fibers. Its most commonly used example is ""fiberglass"", i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [3]."

Jan 1, 2013

By D. Kennis

"Union Miniere Precious Metal's (UMPM's) Hoboken Business Unit has a long tradition in complex Pb-Cu metallurgy, focussing on the recovery of precious metals from various types of secondary and recyclable materials. Although the old flow sheet, based on a traditional sinter plant, blast furnace, and lead refinery process was a very complete flow-sheet with the capability of dealing with almost every impurity, the weaknesses became clear:1. old and costly technology,2. too many unit operations,3. too much internal recycling, and4. dependency on concentrates for the sintering process.To maintain the competitiveness of the Hoboken Business Unit, the project ""Smelter 2000"" was born. This project represents a breakthrough in metallurgical processes and technology. A modem smelting technology was chosen together with the development of a new process. A lead-copper process combining lead slag and blister copper production, carried out in an ISASMEL T vessel, was the key to simplifying the Hoboken flowsheet. ISASMEL T smelting technology was chosen for its flexibility towards feed characteristics and process parameters.The new smelter was commissioned at the end of 1997. Although there were a lot of problems due to the high degree of technical innovations in the process, the new smelter came to design capacity within 1 year after start-up. During this period, however, UMPM had, a very difficult time because of the extreme clear-cut nature of going from the old to the new flowsheet.After two and a half years of operation, the new flowsheet has proven to fit with the strategy of UMPM, focussing on treating secondary Pb-Cu materials and a broad range of recyclable feeds such as electronic scrap (E-scrap) and catalysts. Together with the new Precious Metals Plant, efficient logistics, recognised world class sampling practices and a customer-focussed commercial organisation, UMPM Hoboken can definitely be considered reborn."

Jan 1, 2000

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By James C. Sever

The mode of operation of dolomite kilns at a magnesium reduction plant using the Magnatherm process was designed to minimize operation cost and maximize kiln refractory life. Analysis of downstream operation issues shows the quality metric for dolime changed from loss on ignition to specific surface area. This produced a complete change in kiln operation; the net results being major plant productivity increases decrease in operating cost, and increases in both kiln operating costs and reline frequency.

Jan 1, 2015

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By Tianzu Yang, Weifeng Liu, Lin Chen, Qingkai Xiao, DUCHAO ZHANG

To solve the problem of low leaching ratio of direct gold cyanide leaching from arsenical refractory gold concentrate, this paper proposed a matte smelting process for gold enrichment in low grade copper matte. The effects of copper content in the mixed material, ratio change in slag type, smelting temperature and reaction time on recovery rate of gold and copper were investigated. The experimental results indicated that the recovery rate of gold increased with the increase of copper content in the mixed materials, temperature and reaction time. It was also noted that the recovery rate of gold and copper were respectively 98.16% and 96.39% when the addition of copper content in the mixed material was 3%, slag type of CaO/SiO2 and FeO/SiO2 were 0.6 and 0.9 in 1250°C and the time of reaction was 40min. Most of the arsenic was oxidized into As2O3 existed in the dust. The results showed that the matte smelting method can achieve efficient recovery of gold from arsenical refractory gold concentrate.

Jan 1, 2016

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By Takashi Ikeda, Masafumi Maeda

"Demand for solar cells is increasing linearly throughout the world. Last year production totaled 3000 tons worldwide. The market size of solar silicon is expected to increase further because of international ""political"" demand to reduce carbonaceous emission from energy consumed. Most elemental silicon is produced by the carbon reduction of Silica in an electric arc furnace. Purity of silicon at this stage is 90-99%. Major impurities are Fe, Ti, Ca· and Al, and minor ones are P, B and carbon. The oxidizing metallurgical process is no longer effective to remove transitfon metals because those are less noble to silicon. Nonmetallic impurities such as phosphorus and boron must be reduced to 0.001ppm for semiconductor use. The most common process for high purity silicon is the Siemens C process, which is basically distillation of hydro-chlorinated silicon followed by CVD of SiHCl3. The cost of such silicon is expensive to allow its popular use in solar cells. Currently scrap silicon -of semiconductors is used for this; however, the supply-of that scrap is limited to just a portion of semiconductor production.In this paper world demand for silicon will be reviewed and some of the processes proposed summarized.IntroductionSilicon is element 14 in atomic number and has an atomic weight of 28.0855. Little elemental silicon is found in the earth, and it is mostly found as oxides or silicate. The Clark number of silicon is very large and the second in its number. If we were discussing the volatility of silicon element on the globe, we would never worry about it. However, it is very difficult to obtain pure elemental silicon because a high purity silicon compound is very rare. In most cases these are silica (silicon oxide SiO2). As shown in Table 1, there are many grades of silica ore classified mainly by their content of iron and alumina."

Jan 1, 2000

By Chengxian Lui

Detailed mineralogical and metallurgical investigations were carried out on a phosphorous-bearing manganese carbonate ore from the Huayuan manganese mine, Hunan, China. Microprobe analyses indicate that the Manganese occurs mainly in calc-rhodochrosite and in rhodochrosite. The cOll'pOsitional range of these manganese carbonate minerals is 50 -80 % MnOJ3, 0 -35 % CaOJ3, 5-35 % MgC03 and 0 -15 F~. The manganese carbonate minerals are very fine grained, IOOSt are between 4.6 and 9.4 1m in diameter. The small grains are clustered into aggregates that form bands 0.5 to 10 rnn wide. The phosphorous-bearing mineral in the ore is fluorapatite and is in grains that are generally smaller than 6 1m in diameter. Metallurgical tests show that it is possible to concentrate the aggregates of manganese carbonate minerals by high intensity magnetic separation, and to reduce the phosphorous content by rpasting the concentrate to convert the manganese carl::x>nates to insoluble hausmannite, and then leaching the roast product with HCI to dissolve the fluorapatite.

Jan 1, 1989

By Peng Jianping, Feng Naixiang, Di Yuezhong, Wang Yaowu, Pan Xijuan

A vacuum silicon thermal reduction lithium process is developed in present work which used lithium hydroxide, alumina and calcium oxide as raw materials. The process contains two steps, which are that Li5AlO4 clinker is prepared in ambient environment, and that metal lithium is extracted from Li5AlO4 clinker with ferro-silicon alloy as reductant in vacuum. On the basis of thermodynamic analysis and investigative experiments, feasibility of this process is proved. The results show that Li5AlO4 can be generated by calcination lithium hydroxide and alumina, the burning loss is above 31% under the conditions of calicination temperature above 750℃ and time more than 90min. The main phases of calcination product are Li5AlO4 and CaO. When the calcination product is reduced by ferro-silicon alloy in vacuum, the lithium reduction ratio can be over 80% under the conditions of reduction temperature 1200℃ and reduction time 60min.

Jan 1, 2014

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDS? metals precipitation system to control a mine drainage problem. The effluent from the mine contains primarily zinc, manganese and iron, plus varying small amounts of cadmium, copper and lead. The flow from the mine averages 350 gpm, and varies considerably depending on season and weather conditions. The plant was designed to treat 1000 gpm of the water and generate a dense sludge suitable for recycling. The HDS? system contains a number of reactors, followed by post filtration and meets stringent metals discharge criteria as specified by New Source Performance Standards.

Jan 1, 1994

By Bogdan Petkovic, Boban Todorovic

In the early 90's a completely unknown problem was encountered at the converter Department: it was a chronic shortage of the cold copper charge needed for the second operating period. A high temperature operating regime was caused which further provoked a chain of consequences such as a drastic drop of the number of operations in campaigns. The consumption of repair bricks reached the quantity of 8.3955 kg / tonne of anode Cu. In 1994, we won the process of cold material smelting during the "copper" blowing [2]. The number of operations per campaign reached 180-200 again. Also in 1994 we won the process of smelting cold materials to obtain "tin" blowing with the purpose of completing their processing cycle [2]. During the period 1994 – 2007 a total of 107,845 tonnes of cold material were remelted to make copper and 56,794 tonnes were re-smelted to obtain "tin". Upon synthesizing these two processes, a completely new model was achieved in 2005, by Bogdan Petkovic, which entirely utilized all available energy of the Peirce-Smith (PS) converters of the Bor Copper Smelter and now represents the basis of the time cycle. The cold material now enters the converter plant, copper recovery is increased and the method itself is environmentally friendly. 167

Jan 1, 2009