Search Documents

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

The effects of microwave roasting on separation of rhenium (Re) and molybdenum (Mo) from a molybdenite concentrate have been investigated based on evaluation of the heating characteristics of the concentrate in the microwave field. The results show that a variety of operating variables, namely microwave power, sample weight, sample geometry, roasting temperature, roasting time and atmosphere significantly impact on the volatilization rates of Re and Mo. The optimum conditions for Re-Mo separation are microwave power 1300 W, sample weight 20 g, sample geometry pellets, temperature 600 oC, time 1.5 h, and atmosphere 20%O2. Under these experimental conditions, the volatilization rate of Re reaches 88.12%, while that of Mo is just 5.15%. Microwave-assisted roasting provides an alternative route to separating Re and Mo from molybdenite concentrate.

Jan 1, 2016

By Cleusa Cristina Bueno Martha de Souza

Nowadays in Brazil the final disposal for spent batteries include sanitary and industrial landfill for hazardous waste from domestic waste and industrial waste respectively. The problems of environmental impact caused by spent batteries had been discussed of several years, considering the fact of metals contents, like Cd, Hg, Pb and Zn. Some techniques are been proposed for recycling this type of waste in order to protect the environment while bringing also economic advantages of recovering metals. The reclamation of metals from secondary raw materials had been employed and further applications of this flexible technology are planned to the future. The processing of metals solutions involving hydrometallurgical techniques is an efficient method for recovering metals, since it provides completely recovery of metals with low energy requirements. This paper discusses the spent alkalline batteries characterization and leaching stage experiments results with sulphuric acid as leachant. After batteries dismantling by mineral processing techniques, the black powder sample produced was submitted to diffraction X-ray characterization and atomic absorption spectrophotometry in order to verify all the substances presented. Some experiments were carried on to develop a hydrometallurgical process for initial metal recovery aiming to get Zn into a soluble form on aqueous solution in order to propose the next stages of purification and recovering Zn, as electroplated deposition. The sulphuric acid was chosen not only for being cheaper than other leachants but also for improving the extraction of soluble Zn as ZnS04 form at diluted acid concentration. Batch laboratory experiments leaching procedure were conducted to determine appropriate leaching conditions from the viewpoint of maximize zinc extraction. In these tests an amount of dry powder batteries was added to different acid concentrations and solid/liquid ratio and after leaching and filtration the aqueous solutions were submitted to atomic absorption spectrophotometry analysis to verify the Zn content.

Jan 1, 2000

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By M. Okido, R. Ichino, K. Kuroda

"Compound semiconductor, ZnTe, was electrodeposited in an acidic solution with K2TeO3, ZnSO4 and Na2SO4 solution. Since the reduction potential Te(IV)/Te(O) is remarkably noble from the solution comparing to Zn(II)/Zn(O), code position of Te and Zn was thought to be difficult from this solution. Resulting from EQCM analysis, furthermore, Te(IV) reduced to Te(O) and Te(-II) in this order so that Te catholically dissolved from the electrode surface at more negative potential. But ZnTe alloy were formed by the UPD of Zn at -0.7V at 298K on Te surface in lmM K2TeO3, 100mM ZnSO4 and 100mM Na2SO4 solution adjusted at pH 4. Content of Te in the deposits is, however, more than 80%.Electrolytic temperature is well known to affect on the deposits characteristics. The higher bath temperature was, the better ZnTe crystal was detected in this study. Thermal electrode method is a. process of heating only substrate by flowing ac current in substrate. This process makes the surface temperature of substrate higher than boiling point of the solution, 373K. From EDX analysis, deposits without thermal current were Te-rich, Te content in the deposits with thermal current decreased with increasing of thermal current. Te content was 62% for 5A ac current, 51 % for I OA and 45% for 20A, respectively. The deposits that produced with ac current of IOA were closed to the stoichiometric ratio, i.e. ZnTe.Consequently, thermal electrode method is more effective to obtain a good crystallized ZnTe without heat treatment after deposition.IntroductionThe current subject of solar cell materials is silicon. Compound semiconductors including GaAs and II-VI group are generally used in the developing field of digital information such as the rapid cellular phone and car telephone. Compound semiconductors consist of more than 2 kinds of element. There are many materials for these compound semiconductors such a SiC, InSb, CdS for binary system and CuinSe2 for ternary system. It becomes generally difficult, to produce high quality crystal with increasing of kinds of element due to a complicated structure and a compound ratio of element. Semiconductor materials as a device are usually simple binary compounds and/or these mixed crystals. Properties of compound semiconductors have variety of the forbidden band and lattice constant and that can be change easily by addition of another element for the usage of the solar cell. Since most compound semiconductors are direct interband transition type, which has steep optics absorption edge and large light absorption coefficient."

Jan 1, 2000

By Yuanyuan Wang, Hong Li, Xueting Liu, Hao Bai, Kang Zhou

"Phase change materials are widely used in efficient utilization of energy and new energy technology. Especially, more attention has been paid to composite phase material, which is applied on architectural energy-saving and efficient working fluid. In this paper, stearic acid-silicon dioxide composite material was prepared by sol-gel process from tetraethyl orthosilicate (TEOS) and stearic acid (SA). The material was investigated by Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and Differential scanning calorimeter (DSC). The FE-SEM results show that 3D-grids of silicon dioxide were formed clearly and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reactions between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity. This material is expected to be used to make a cooling working fluid.1. IntroductionEnergy thermal storage becomes increasingly prominent issue in recent years, because thermal storage has been used in many aspects, for example, it can be added into building materials to improve heat conditioning. Another potential application of thermal storage materials is that the intermittent waste heat can be collected and recycled effectively by using the thermal storage facility. Thus, energy thermal storage plays a significant role in conserving available energy and improving its utilization [1]. Energy thermal storage includes sensible heat storage and latent heat storage. The latent heat storage has great heat density with a constant temperature during the phase change process [2-5]. Large quantities of latent heat storage will be absorbed and released when phase change takes place. Based on the former researches, some phase change material (PCM), such as fatty acid and paraffin waxes, has been proved to have high latent heat storage capacity and appropriate thermal properties [5-6]. However, using the PCM in energy storage systems directly is restricted, e.g. some properties of organic PCM, like form-stability and thermal conductivity, are not good enough to use. Meanwhile, almost all the inorganic PCMs are corrosive and most materials may cause sub cooling and segregation [7-9].The other problem is that the leakage when the temperature reaches the phase change point. Therefore, encapsulated composite phase change material (CPCM) emerged in order to solve the problem of leaking out, minimize the sub cooling and prevent phase segregation. [10-13] However, the easy flammability of fatty acid also has hindered the development of PCM. Accordingly, it has been found out that silicon compounds are environmentally friendly promising substitutes for halogen-containing flame retardants. Especially, silsesquioxanes are excellent in the flame retardancy. So CPCM can be encapsulated with SiO2 acting supporting material."

Jan 1, 2014

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By Bora Derin, Sertac Yazici, M. Seref Sonmez

"In this study, the recycling conditions of waste liquor obtained after the production of tungsten boride powder from calcium tungstate by self-propagating high temperature synthesis (SHS) and the following hydrochloric acid leaching were investigated in detail. Environmentally unfriendly and extremely acidic (pH~ -0.3) liquor consisting of calcium, magnesium, and boron ions was treated with 1 M sodium carbonate solution to precipitate magnesium carbonate and calcium carbonate phases. The obtained amorphous precipitates were heated up to the temperature of 400°C for re-crystallization. As a result, MgO, CaC03 and CaMg(C03)z phases were obtained, while sodium, boron, chlorine ions were remain in the solution. The present study is still in progress.IntroductionSelf-propagating high temperature synthesis (SHS) is one of the techniques used in the production of a variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers [ 1, 2]. The reaction becomes selfsustaining and propagates in the reactant mixture, after initiation in SHS process. SHS products may contain the mixture of several unwanted compounds and elements. Therefore following acidic leaching process may be needed to purify the target product. In the previous study, calcium tungstate (Ca W04), magnesium (Mg) and boric acid (B20 3) mixture were reacted to produce tungsten boride powder by SHS process according to the Reaction 1. Then, magnesium and calcium containing byproducts (i.e. MgO, Mg3B206 and Ca3B206) found in the SHS product were leached out by using concentrated hydrochloric acid (HCl) solution to obtain pure tungsten boride powder [3].Ca W04 + 0.5B203 + 4.5Mg = WB + 4.5Mg0 + Cao (1)After the leaching, filtrate solution consisting of different amounts of magnesium, calcium, and boron requires additional treatment for the environmentally acceptable disposal.Several works were carried out about magnesium precipitation conditions and kinetics from brines. Rabadzhieva et al. investigated the precipitation of Mg(OH)z from brines by using NaOH as well as caustic soda [ 4]. Turek ve Gnot investigated the precipitation efficiency of Mg(OH)z for the temperature range between 10-40°C, while the reaction was kinetically experimented by Alamdiri et al [5, 6]. Homogeneous precipitation of nesquehonite (MgC03.3H20) by the reaction of MgCli with (NH4)2C03 in supersaturated solutions and factors that influence the precipitation of MgC03.3H20, such as reaction temperature, initial concentration, stirring speed, titration speed, equilibration time, have been studied by Wang et al [7]. The precipitation of Mg(OH)z by calcium hydroxide from aqueous solutions was studied by Baird et al. [8]. Stratful et al. focused on conditions influencing the precipitation of magnesium ammonium phosphate from wastewaters [9]. 1031"

Jan 1, 2011

By Vladimir Lobanov, Vladimir Skorohodov, Andrew Evdokimov, Ural State Technical University 19, Boris Radionov

"The bulk of raw materials in metallurgy of secondary platinum metals are the wastes such as multilayered ceramic-metal systems, e.g. the spent catalysts of the chemical and petrochemical industry, automobile catalysts, etc. Due high chemical resistance of a ceramic basis the extraction of platinum metals by leaching even at very fine crushing is poor. The study of sorption leaching of platinum and a palladium from the spent automobile catalysts are carried out. The average content of PGM is 0.5%. A few methods of raw materials sampling were compared: 1) direct hydrometallurgical leaching of platinum metals from the fine-grained catalyst and atomic absorption analysis of the obtained solutions; 2) fusion to a metal or sulphidic collector of precious metals with the alloy analysis by direct spectrometry; 3) fusion with dissolution of a precious metals collector and atomic absorption analysis of PGM in solutions. Leaching allows detecting out no more than 90% of a palladium and 80% of platinum. Fusion to a collector gives the best results at the chemical ending. Researches on sorption leaching are executed. Under optimum conditions the extraction of platinum metals to concentrates is comparable with similar indicators of collector fusion.The large part of raw materials in metallurgy of secondary platinum metals are the multilayered or tridimensional ceramic-metal systems, in particular the spent catalysts of the chemical and petrochemical industry, automobile catalysts, ceramic-metal condensers, etc. The content of the sum of PGMs can be from hundreds grams per ton to several percent. For processing of such materials the hydrometallurgical methods of platinum metals leaching by various reagents are used commonly. High chemical resistance of the ceramic basis covering the metal particles causes low recovery even at very fine grinding. Other fundamentally different method of catalysts opening includes dissolution of the ceramic basis in the solutions of hydrofluoric acid and the subsequent recovery of platinum metals from insoluble residue. Application of this method is associated to use of corrosive medias and appropriate equipment. Fusion of the specified materials with collecting of PGM by copper, nickel or lead at the specialized enterprises provides higher extraction in semiproduct. At the same time, complexity and duration of the subsequent extraction of platinum metals concentrates causes high total cost per unit. Thereby this method is economically acceptable only for rather poor raw materials (no more than 0,1%). Undoubtedly, that the raw materials with the high content of PGM are reasonable to process by individual technology. In the present work the processing of some kinds of ceramic-metal raw materials, particularly automobile catalysts (neutralizers) with various collectors at the conditions of a target fusion are investigated."

Jan 1, 2008

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"The structural and electronic properties of cubic d -NbN are investigated using density functional theory (DFT) and all-electron full potential linearized augmented plane wave method (FPLAPW). The equilibrium structural parameters are determined by fitting the total energy as a function of volume to the Murnaghan's equation of state. We calculated the total and partial densities of states (DOS) and compared them with those computed by different authors. Our DOS at Fermi level is found to be very close to the experimental value. The band structure is computed, discussed and used to find the characteristic energy separations. Valence electron density contours are recorded and discussed. We deduced the partial charge densities of different bands and binding energies of valence core levels and compared them with experimental and theoretical results obtained by different authors.IntroductionNiobium nitride has been intensively investigated over the last decades because of its interesting physical properties and technological applications (superconducting microdevices, microelectronic, catalytic probes, and hard coatings) [l]. While the group IV transition metal nitrides (TMN) mainly crystallize in the cubic NaCl structure (Bl type), those of group V and VI nitrides occur as different phases. Thus for niobium nitride, many phases have been reported in the literature: cubic fcc d -NbN, tetragonal ? -Nb4N3, hexagonal d -NbN, hexagonal e -NbN, and low nitrogen content hexagonal ß -Nb2N [l, 2].Structural and electronic properties of niobium nitride were investigated theoretically and experimentally by many authors. For example, in 1975 Schwarz [3] obtained the partial density of states for NbC and NbN from APW band structure calculations. In 1975 Kallne and Pessa [4] studied the electronic structure of Nb, NbC and NbN by using X-ray emission. In 2003 Amriou et al. [5] studied the electronic structure and bonding mechanism of NbC and NbN compounds using first principle total energy calculations using the full-potential linearized augmented plane wave method. Also in 2006 Sanjines et. al [l] studied the electronic structure of the hexagonal~Nb2N, hexagonal' d -NbN, and cubic d -NbN thin fihns by using X-ray photoemission spectroscopy. They [l] also calculated the densities of states for these phases and used them in the interpretation of the experimental valance band spectra. Most of these studies are old and there is a need for more recent studies. According to our knowledge, there are little comprehensive theoretical studies on this subject by using FP-LAPW method [5], which proved its ability to give accurate results. In this work we used the FP-LAPW method to study the structural and electronic properties of the cubic (fee) o-NbN (space group Fm-3m, prototype NaCl) crystal."

Jan 1, 2013

By Björn Hinzel, Joachim Rösler

"The most important characteristic of open-pored metals is porosity, since it enables all of their functional applications as filters or sound absorbers. Due to the notch effect of the pores, mechanical properties of porous metals are better than the ones of comparable structures made of polymers or ceramics. Consequently, only open-pored metals can be used in aircrafts to reduce flow noise or noise resulting from the core engine by acoustic absorption. Absorption properties depend highly on pore size and porosity of the material, which must be characterized as precisely as possible in order to analyze the correlation between morphology and noise reduction performance. Here, a line segmenting method is explained in order to characterize pore size and porosity of absorber materials using image processing based on two dimensional microscopy images, including sample preparation and specification of the set-up. Then, the influence of the pore structure on the measured absorption behavior is discussed. Finally, the correlation of acoustic behavior, pore morphology, and porosity is outlined.IntroductionSignificant noise loads affect everyone causing anxiety, depression, insomnia and other effects which impair health and productivity [1],[2]. Due to the rising number of flights and aircrafts, air traffic noise increases dramatically. To counter this development, various approaches have been developed to reduce the different noise sources resulting from airframe, jet or engine [3],[4],[5],[6]. One approach to reduce this noise is the application of noise reducing liners in the hot gas path [7]. This is especially important, since the engine is becoming the dominant noise source of modern airplanes during take-off [8]. Due to the elevated temperatures and high fatigue loading in this part of the aero-engine, conventional passive absorber materials cannot be used. Polymers would not be able to bear the heat and ceramic fibers would crack under the mechanical loading due to the notch effect. Consequently, this study focuses on metals with open pores, which can resist elevated temperatures and fatigue loading and additionally resemble geometrically conventional passive absorbers. Based on the production processes, e.g. sintering of metal fibers [7], powder processing using a foaming agent [9], coating of polymer foams [10], or using melt infiltration techniques [11], the characteristic dimension of the porosity is usually in the range of 0.01-10mm. In this work, sintered metals and metal sponges are analyzed after the theory of sound absorption is briefly outlined. Then, measurements of the acoustic absorption of metal sponges and sintered metals in an impedance tube are performed. To understand and predict the acoustic properties of metals with open porosity, it is necessary to characterize the materials as precisely as possible. This is explained in detail using a line segmenting technique, followed by a discussion of the connection of pore characteristics and acoustic absorption. Finally, a conclusion is given."

Jan 1, 2012

By Sridhar Komarneni

"Microwave-hydrothermal processing is a novel technique which combines the conventional hydrothermal processing with microwave field and we previously showed for the first time, that ceramic powders can be rapidly produced by this technique. This review paper deals with the synthesis of unary oxides such as Fe203, Ti02, Zr02, etc., binary oxides such as BaTiO3, SrTiO 3, PbTiO 3, SrZrO 3, KNbO3, etc., and ternary oxides such as NaTi2 (PO4)3 and pyrochlore phases of Pb(Mg1/3Nb2/3)O3, Pb(Zn1/3Nb2/3)O3 etc. and metal powders such as Cu, Ni, etc. below 195°C. This method can be adopted to the synthesis of a large variety of powders by the appropriate control of pH, Eh, temperature/pressure and concentration of chemical species. The main advantages of this method compared to conventional hydrothermal processing are (a) it increases the kinetics of reaction by one to two orders of magnitude, and (b) it can lead to novel phases especially those with layered structures.IntroductionConventional hydrothermal processing is a well-established synthesis technique which has been extensively used in the preparation of fine ceramic powders [1-5], large single crystals [6-8] and massive cement blocks [9]. Technologically important ceramic powders such as BaTiO 3, Al203 etc. made by the hydrothermal process are now commercially available. Although there are numerous methods for materials synthesis, hydrothermal method is truly a low temperature and environmentally benign process. For example, ZrSi04 (Zircon) which is extensively used in ceramic industry can be prepared hydrothermally at 150·C [10] compared to sol-gel or solid-state method [11,12] which require a temperature of about 1000·C. The hydrothermal method is environmentally benign because hydrothermal reactions are carried out in closed systems at low temperatures and the contents can be recovered and recycled after cooling to the ambient conditions. One of the disadvantages with any low temperature processing method is slow kinetics. For this reason we have combined the hydrothermal method with microwaves to enhance kinetics and we named this method as ""Microwave-hydrothermal"" processing [13- 16]. Although the combination of microwave and hydrothermal techniques has been used in the past few years to dissolve all kinds of inorganic (e.g. alumino silicate rocks) and organic materials rapidly for chemical analysis, we were the first to show its potential value for the synthesis of various ceramic powders [13-16]. In this paper, I show that this novel method is applicable to the synthesis of all unary, binary and multinary oxides by the appropriate control of pH, Eh, temperature, pressure and concentration of chemical species. In addition, this method is also found to be useful for the preparation of metal powders."

Jan 1, 1994

By Andreas Stieben, Pierre Lutomski, Wolfgang Bleck, Martin Fischer

"For steel investigation and development, exact knowledge about the microstructural state is required. The information gained from 2D images often can't properly reflect the real 3D microstructural properties. In order to gain reliable information for meaningful models, simulations and correlations, it is necessary to accompany standard metallography with 3D information, which, unfortunately, is very difficult to access. This article presents a procedure for serial sectioning in combination with light optical microscopy. Only standard metallographic tools are employed in combination with image manipulation freeware. 3D microstructural data were extracted from three multiphase steel grades and in two cases virtual 3D-models of microstructural phases were generated.Three Dimensions Of MicrostructuresSince the invention of steel, craftsmen, inventers and engineers tried to improve its properties and tailor them to the requirements of new developments. For systematic development and enhancement of steels, the capability to investigate its inner structure is highly important, because it represents the linchpin between material production and properties. By having an in-depth understanding how production conditions form the microstructure and also how the microstructural state determines the material properties, steel design can be drastically improved. With this knowledge, microstructures can be designed to provide target material properties and process conditions can be identified that form these structures. Due to the key role of microstructure, the capability to gain accurate information about it is indispensable. It is the task of metallography to access and extract descriptive quantitative microstructural data like fractions, sizes, shapes and distributions of the different constituents. The most commonly used investigation tool in metallography is the light optical microscope (LOM). Besides this tool, additional high resolution techniques like Scanning Electron Microscopy (SEM) or Transmission Electron Microscopy (TEM) have become increasingly important. With these and other available methods, extensive information on the microstructural state of a material can be gained. Unfortunately, most metallographic methods have a major loss of information systematically built in. Analyses of microstructures are usually performed on surfaces, i.e. on 2D areas that emerge by cutting through the 3D material structure. This means, a complete dimension of information is not taken into account. How serious this reduction of information is and how it can affect interpretation of structures is exemplarily demonstrated in figure 1, which displays the planar structure emerging from a random cut through a simple 3D structure. It is very difficult to deduce or even imagine the original spatial structure from which this projection emerged and it is impossible to reconstruct it with absolute certainty without further information. The image has emerged from a random cut through a 3D structure of stacked cubes that is displayed in figure 2. The area shown in figure I is outlined. Although artificially constructed, this example demonstrates how distorted and misleading the view on structures can become by ignoring a spatial dimension."

Jan 1, 2012

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008