Search Documents

By Wen-long Zhan, Zhe Ning, Jun-hong Zhang, Ji-hui Liu, Zhi-jun He, Qing-hai Pang

The influence of microwave irradiation and ultrasonic vibration on granularity of 0.074 mm pulverized coal was investigated in this research. It is indicated in the results that the granularity of coal decreased after microwave treatment, which led to the increased in specific area of pulverized coal in combustion reaction and consequently optimized the kinetic condition of combustion reaction. Higher ultrasonic power may lead to better performance of PC in combustion. The optimum condition for ultrasonic treatment is 10 min under 350 W microwave power.

Mar 1, 2017

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By Wayne C. Stewart

Freezing of high pressure air lines and pneumatic equipment has been a recurring problem in the Thompson Smelter. The particular severity during the winter of 1989-90 resulted in costly process disruptions and repairs. A process improvement team with representatives from operations, engineering and both maintenance supervision and the shop floor was established to develop solutions. Their mandate included process evaluation, design, equipment and in-plant commissioning. In 1990, upon recommendation of the team, we installed three Refrigerant/Desiccant air dryers with a total capacity of 20,000 S.C.F.M. to service the Smelter. This paper discusses processes and process improvements associated with this installation.

Jan 1, 1993

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By P. F. Kerr

This is not a conventional professional paper. It deals mostly with personal experiences. These concern a background in applied mineralogy. Your committee asked me to do this. I accepted with a California enthusiasm which has since diminished with the approach of a Chicago winter. Nevertheless, I wish to thank your committee and also to apologize in advance for omissions and inadequate statements, as such a paper must possess. My introduction to applied mineralogy took place in 1922 at Stanford University. Physicists had recently demonstrated that crystalline powders would reflect x-rays in a systematic manner. Professor A.F. Rogers sug¬gested that significant x-ray reflections might be obtained from powdered opaque minerals. With the aid of Professor D.L. Webster in the Physics Department, I constructed an x-ray diffraction outfit. It was a crude affair, but it worked. Starting with 1924, we secured recognizable patterns of a goodly number of ore minerals (1,2,3). Today x-ray diffraction outfits are common, and a card system of mineral identification is constantly used.

Jan 1, 1981

By N. Bazzanella

The hydrogen desorption kinetics of pure and Nb-doped magnesium hydride film samples was investigated by using a Sievert-type apparatus. The overall activation energy and the reaction order controlling desorption are (141±5) kJ mol-1H and n 4 for Mg hydride and (51±5) kJ mol-1H and n 1 for Nb-doped (5% at) Mg hydride indicating that, in the doped sample, hydrogen desorption is controlled by the H migration in transformed h-Mg layers. Structural analysis performed by X-Ray Diffraction (XRD) and Extended X-Ray Absorption Fine Structure spectroscopy (EXAFS) show that the catalytic effect of the Nb dopant is connected with the formation of NbH0.89 nanoclusters dispersed in the Mg hydride matrix. It is suggested that the catalysis process is also connected to the presence of Mg-Nb hydride interfaces where the transfer of H atoms preferentially occurs by connecting h-Mg grains and by the role of the MgH2-NbH0.89 interface as preferential site for the dissociation of the hydride phase.

Jan 1, 2006

By Theo Lehner

"During my first contact with industrial metallurgy as a summer vacation worker at the Steelplant at Luleå, Sweden, I came during a visit to MEFOS into contact with works of Prof. Worner caried out during the piloting of the Worcra continuous steelmaking process. These tests are still today remarkable as an innovative step in the art of metalmaking. By that they involved the necessary ingredients for the development of our art: seeing, knowing and doing. Industrial injection as applied during slag fuming will be discussed below.Phenomena of injection metallurgyPhenomenon according to Collins dictionary is"" anything that can be perceived as an occurrence or facts by the senses"". To open the senses for the interesting phenomena in pyrometallurgy must be the main task of any educator. The investigations by Engh et al. around the mixing phenomena of the WORCRA process are an early example of combining senses with knowledge. To see what you model must be a crucial part in any development. This can also involve to see and control that one is subject to the same conditions as in published models. Below the need ""to see"" will be illustrated by some recent investigations around slag fuming. In the literature various models for reactions occuring during the fuming of slags are presented. Two recent models hint ·ata) the occurrence and importance of iron for the fuming processb) the occurrence and importance of lead droplets during respectively."

Jan 1, 1996

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Emil B. Milosavljevic

Problems associated with distillation and other classical methods for analyzing operationally defined cyanide (CATC, WAD, Total and Free Cyanide) will be discussed. These methods often achieve incomplete, species dependent cyanide recoveries and suffer from serious interferences. Depending on the relative concentrations of interferents and other matrix constituents, underestimation (ultimately Type II errors probability of not detecting a constituent when it is actually present) or overestimation (ultimately Type I errors -probability of deciding a constituent is present when it is actually absent) of the cyanide levels present in a ,given sample may occur, causing in the first case false security and in the second case, excessive cyanide treatment costs. Mahy, if not all, enumerated problems can be solved by using novel flow injection (FI) gas-diffusion amperometric methods. A modification of the recently approved FI ligand exchange (FIILE) method for determination of available cyanide (USEPA Method OIA-'l677) that obviates sulfide interference will be discussed. Eight laboratory round-robin data obtained for the FI UV -digestion (FIIUV) method that determines total cyanide (Proposed Method OIA-1678) will also be presented. In addition, some methods for cyanide speciation will be presented. Finally, research needed for developing reliable methods for determination of operationally defined cyanide in solid samples will be summarized.

Jan 1, 1998

By John R. Goode

Barrick Gold Corporation operates gold mines in the United States, Chile, 'Peru, Canada, and in the near future, in l1anzania. Barrick meets environmental requirements and limits the potentially adverse effect of cyanide discharge to the environment using various cyanide destruction techniques. Barrick operations use, or have used, natural degradation, ferrous sulphate, hydrogen peroxide, Caro's acid, alkaline chlorination, and the SO/Air process for cyanide destruction. This paper presents a general discussion of the options for controlling cyanide in plant effluent and provides details of Barrick's operating experience including general notes on costs.

Jan 1, 1998

By J. B. See

Emeritus Professor David Robertson of the Missouri University of Science and Technology was born in Dublin Ireland on 29 December 1941. His father was a merchant navy Captain who served during WWII and during David’s early years his family lived in Dublin and Donegal where David went to the local elementary school. In 1954 he moved to London with his parents and attended Highgate School before commencing metallurgy at the Royal School of Mines, Imperial College, London in 1960.

Jan 1, 2014

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By Jerry L. Smith

Industry on a whole has not been very receptive to government prodding to implement waste minimization programs. Waste minimization has the appearance of substantial benefits, however, there are underlying difficulties and suspicions that need to be addressed before industry will support pollution prevention initiatives. They can be summarized as follows: - Human behavior resists change, uncertainty, and unknowns. - New waste minimization techniques are difficult to find and research. - Calculating the true cost of present waste practices as well as new techniques being considered is difficult and time consuming. - Getting a consensus opinion of all the individuals affected on the course or technique to be employed in a pollution prevention program. New software products have addressed many of the problems associated with implementing pollution prevention programs: They contain research on a large number of pollution prevention techniques and case studies; they generally are accessed by EPA ID number, chemical name, or synonym; and some programs have the option to print a comprehensive written user-specific pollution prevention program.

Jan 1, 1994

By P. Myllykoski, J. Nylander, A. S. Korhonen, J. Larkiola

The coefficient of friction and the deformation resistance have been determined from the measured rolling parameters by applying the Bland-Ford-Ellis rolling force model and the artificial neural network model (ANN). The dependence of friction on the parameters such as reduction, rolling speed, front and back tensions, contact pressure and deformation resistance have been studied by the ANN model. Measured data of over 10 000 coils have been used in the training stage. Various dependencies have been examined and the results show that the friction coefficient does not depend much on the rolling speed. The reduction and deformation resistance seem to have the strongest effect on the friction coefficient. A friction model based on neural computing has been included into the existing rolling force model.

Jan 1, 1994

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

By Taner Kavas

In the present study the utilization of coal ashes that appear at the end of firing process of brick production in cement pastes was examined. Ashes with three different particle sizes of 75 µm, 106 µm and 150 µm were used to replace ordinary Portland cement (PC) as 5 % and 15 % by weight. Seven samples were prepared and physical, mechanical, chemical and microstructural analyses were carried out. The compressive and bending strength values of samples were determined at the ages of 2, 7 and 28 days. It was found that cementitious pastes with finer particle sizes possessed the highest compressive and bending strength values at all curing ages. Both values after 2 and 7 days cure increased with an increase in ash content, no matter what the particle sizes of ashes were. However, strength decreased after 28 days cure as a result of ash addition of 15 %, although it was still above that of the PC.

Jan 1, 2006