Search Documents

By Jae-Chun Lee

Di-2-ethylhexyl phosphoric acid (D2EHPA) is widely used for separating rare-earth elements. In commercial plants, rare-earths are usually stripped from loaded extractant streams using mineral acid, then precipitated as oxalates. Many rare-earth uses demand specific powder characteristics, which are obtained by secondary processing. This paper demonstrates the feasibility of combining the stripping, precipitation and powder processing stages, thereby achieving considerable savings. MEHPA solutions were loaded with yttrium, then emulsified with oxalic acid-HC1 solutions to precipitate yttrium oxalate, which was readily calcined to yttrium oxide. The precipitation kinetics and yield were sensitive to process conditions. The morphology and size of the yttrium oxalate powders varied with the concentrations of D2EHPA and oxalic acid, and the presence of SPAN 60, which affected nucleation, growth, and the emulsion characteristics.

Jan 1, 1992

By A. Raraz

The optimization of the plutonium electrorefining process has been studied on the basis of modeling and model materials. The plutonium electrorefining process has been reviewed and the basics of the electrorefining process with molten salts as electrolytes and under forced convection has been presented. The definition of the problem in plutonium electrorefining has been related to three factors and this research has addressed these three factors to provide an insight to this process. The hydrodynamic factor gives information on the behavior of the mechanically stirred system. The chemical stability and solidification factor shows the interactions among the components of the electrorefining cell. The electrochemical factor is oriented to study the efficiency of the electrorefining process on the basis of limiting current density, stirring rate and configuration cell. As a result of this study the optimization of plutonium electrorefining implies mainly a re-design of the cell.

Jan 1, 1995

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Kaixi Jiang, Bangsheng Zhang, Lei Zhang, Haibei Wang, Xiaoping Zou

"China plays an important role in the global molybdenum industry; in fact, both China's molybdenum mine and smelter production ranked first in the world. The characteristics of China's molybdenum resources are quite complex, and moly-nickel ores with carbon, coppermoly ores and wulfenite can be only found in China. This paper firstly introduces China's molybdenum resource/ reserve situation. Secondly, the status of molybdenum smelting technologies, especially roasting by rotary kilns and multiple-hearth furnaces, are discussed. The practices and the development of some new technologies, such as pressure leaching, solvent extraction, ion exchange, carbon adsorption for moly-nickel ores and low grade molybdenite concentrates, are also introduced.IntroductionMolybdenum is widely used in special steels, aviation, alloys, chemistry, electronic and medical industries because of its excellent physical and chemical characters [1,2].In nature, molybdenum exists mainly as molybdenite associated with copper ore which are the main material for smelting. About 99% of molybdenum is produced from molybdenite. In addition, wulfenite, molybdenum oxide ore and graphite shale containing Mo-Ni have also industrial value to extract molybdenum and other metals such as Ni, Re, Pb and Zn. The reserves of molybdenum in China are about 8.4 million tons metal; China is ranked as the second largest source in the world. The output in China is more than 40 kt in 2010. Ferromolybdenum is the main product and then ammonium molybdate. The consumption in China is about 20 kt and the rest is exported to overseas.The first molybdenum smelter in China was built in 1963. Today the main producers include Jinduicheng Moly Company, Luanchuan Moly Company and Jiangxi Copper Group Company. Technologies and equipment have changed greatly. Roasting and multi-hearth furnaces are widely used. Several new processes were developed such as pressure leaching, solvent extraction, ion exchange and carbon absorption [3-8]."

Jan 1, 2012

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That's because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it's important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By Tomas Astorga

APEC, the Asia Pacific Economic Cooperation is the forum of 21 countries having approximately 56% of the total world income, and over 45% of global trade. In 1997, APEC economies produced 67% of the world copper output, 55% of gold, and over 45% of other base metals. Mining in APEC captures more than 60% of the total mining investment in the world. New and emerging economies are now appearing in the demand scenery, such as China. New trends in the international environmental regulations are posing questions related to the use of copper in different industrial and consumption applications. These may have a strong impact on future trade of copper. New applications are also appearing based in new technology fields. The paper examines the growth potential of the copper market in main consumer ad highly populated economies of APEC, incorporating analysis of various interrelated factors. It also analyses the outlook of the copper supply. Its conclusions point to the need to implement demand outlook models. Finance and economic reforms will open important avenues for trade growth in basic metals, particularly copper. Changes in the consumption patterns of highly populated countries will add to better perspectives of copper demands. The recovery of a fast pace of economic growth in the APEC region will bring new demands for copper, especially as a consequence of high tech applications. More extended policies focused in the need for developing energy efficiency programs and schemes will add to this picture.

Jan 1, 1999

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By Ju Shao-hua

Although nowadays gold extraction methods are very abundant, none of them is satisfying, especially, in the field of heap leaching of low grade gold ore. The traditional heap leaching method of cyanide method plays an inglorious role of badly environmental pollution. In this paper, a bran-new and innoxious method of gold extraction system, metal-ammonium-chloride-ammonia (MACA), was proposed, and also analyzed both thermodynamically and practically. Thermodynamically, according to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the thermodynamics of Au-NH4Cl-NH3-H2O system was studied by using the exponential computation method and through MATLAB programming, and the solid figure of its potential - c(NH4Cl) - c(NH4OH) was drawn. The results showed when the concentrate of ammonia is higher than 0.6 mol?L-1, fAu+/Au is only about -0.2 v. Practically, the leaching results of a cuprous gold ore showed that the extraction of gold can reach to 80% in this system. The preliminary results of reduction of the rich solution with copper and zinc powders showed that with deoxygenizing, the reduction effects were relatively good. These new findings and results have established a theoretical and practical base for developing a new process for heap leaching of low grade gold ores in this system. And the new process owns a series of merits such as, non-cyanogens, nontoxic, broader applicability.

Jan 1, 2006

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Pekka Taskinen, Hannu Johto

"Copper sulfide concentrates often contain impurities such as lead and iron. The phase stabilities of the sulfide impurity systems in metallurgical process conditions are in many cases unsatisfactorily known. Thermodynamic information of a system gives better understanding of its behavior of metal making processes, but also has effects on the economic and environmental factors of the production process. In this study, isothermal equilibrium and quenching experiments of the stable phases of the system Cu2S-FeS-PbS at 700 and 900 °C were carried out and based on the experimental results, Gibbs triangle of equilibrium phases of the system was outlined.IntroductionThe knowledge of stabilities of phases and the thermodynamic properties of many sulfide systems in the temperature range of 500-1200 °C are quite limited. Especially, the knowledge of liquidus surfaces of multicomponent sulfide systems is essential for making many metallurgical processes more environmental friendly and allowing the utilization of complex concentrates. In this work, the aim was to investigate the phase stabilities of the quasiternary system CU2SFeS- PbS using evacuated silica ampoules. Of greatest interest were the properties of the liquidus surface in the system, in order to be able to predict better the formation of a liquid phase in metallurgical processes."

Jan 1, 2012

By R. E. Aune

In the present work, a critical assessment of the thermodynamic information available for the ternary system Ni-W-0 has been carried out; This was complemented by experimental measurements of the standard Gibbs energy of formation of the ternary compound NiWO, by solid state galvanic studies involving Zr02-CaO solid electrolyte. The assessed thermodynamic data, together with the phase diagram information available in literature, were employed to generate the ternary phase diagram for the system Ni-W-0 in the temperature range 1073-1273 K. The calculation of the phase diagram was carried out by computer optimization according to the "CALPHAD" method. The computed phase diagram has been confirmed at isothermal sections by identification of the phases present in samples equilibrated at defined temperatures.

Jan 1, 1994

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

By S. B. . Tyrrell

This paper describes research carried out to develop and optimise a process to extract lithium from the processed waste of spent lithium ution of lithium salts can be used to produce a pure lithium hydroxide solution, From this, lithium carbonate is produced, the major precursor for other lithium chemicals and for new lithium batteries. Hence, the recycle loop can be closed. Significant variation in the composition of the battery waste has been observed. Small amounts of metals other than lithium and certain anions can present technical difficulties such as electrode dissolution and membrane fouling. Pre-treatment of the waste, together with an optimum combination of cell materials and operating parameters has been found to enhance separation and alter the energy consumption of the process.

Jan 1, 1999

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By M. Olper, M. Maccagni

"The crude zinc oxides (CZO) produced in any thennal process dealing with EAF dust also contain lead, cadmium, and a considerable amount of halides (chlorides and fluorides). The high halide contents make these crude zinc oxides less and less attractive, both technically and economically, and a further refining procedure is nece'ssary to meet the zinc and zinc oxide market requirements.Hydrometallurgical techniques commercially used to dehalogenate the crude zinc oxides are not effective enough to upgrade the crude zinc oxides to the required specification for their direct use in the traditional sulphuric electrolysis by primary zinc producers.The EZINEX® PROCESS has solved the problem of the halides contained in the crude zinc oxides. This process is the only proven technology electrowinning zinc from a chloridebased electrolyte in a conventional cell house. This paper discusses the process economics taking the data from feasibility studies of different size commercial plants."

Jan 1, 2000

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000