Search Documents

By Zhiqiang Zhou, Shengnan Zhou, Zizong Zhu, Yuchuan Ding

The effect of silicon on removal of phosphorus from high phosphorus Si–Mn alloy was investigated at 1673 K by CaO-based slag. It was found that the dephosphorization efficiency increases significantly as increasing the silicon content, which is due to the reaction between silicon and CaO at slag/alloy interface. The relation between silicon content with oxygen activity and phosphorus activity coefficient of Si–Mn melt was determined respectively as follows: lg aO = -1:55xSi - 1:67; ln rP = 9:26e xSi 0:0433 + 11:0839 The carbon content in Si–Mn melt decreases continuously with the increasing silicon content, meanwhile, the decreasing rate of carbon content becomes rapid when the mole fraction of silicon is about 0.32. Si addition is beneficial for both dephosphorization process and low carbon Si–Mn alloy production.

Mar 1, 2017

By A. Kontopoulos

The Olympias Mine in Northern Greece is producing an extremely refractory gold-bearing arsenical pyrite concentrate, containing on the average 41 3 S, 40 3 Fe, 10-12 3 As, 25 ppm Au and 35 ppm Ag. During the process selection stage, more than a dozen alternative technologies? were considered and an in-depth analysis was prepared for the three most promising, ie roasting, pressure oxidation and biological oxidation. Detailed capital and operating cost estimates were prepared, based, where appropriate, on laboratory and pilot-plant tests. A number of criteria was used for process evaluation and selection, including capital and operating costs; environmental impact, gold' recovery, stage of development, etc. Based on the above evaluation, the Sherritt Pressure Oxidation Process was finally selected. A detailed description of the process selection stage, supported with laboratory and pilot-plant test results on many of the processes considered, will be? presented.

Jan 1, 1989

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987

By I. Barin

The thermodynamics of cyclone smelting of sulphidic copper ores is described using as example the production of copper matte with 75 wt % Cu. Equilibrium calcualtions and material and energy balances show that an increase in process temperature from 1600 K to 1900 K results in the extensive transfer of minor elements such as As, Sb, Bi, Pb, Zn,.... to the gas phase. A pilot plant for carrying out the cyclone smelting process is described. Calculations of material and heat transfer for the reaction of ZnS show that the smelting reactions of sulphides in the cyclone take place very rapidly at high temperatures. The dissociation of the sulphides with subsequent oxidation reactions in the gas phase plays an important part in. the process and is mainly controlled by heat transfer.

Jan 1, 1983

By Susan Fredholm, Randolph Kirchain, Jeremy Gregory

"Jurisdictions across the world have struggled to create and finance systems that can effectively collect and process electronics waste (e-waste). Many different system architectures have been proposed and implemented, but it is difficult for policy-makers and system architects to compare the costs and benefits of different systems, particularly when the systems operate in different contexts. This paper presents a systematic methodology that seeks to address this challenge and uses data from several existing electronics recycling systems across the world to illustrate its implementation. The methodology characterizes three main system characteristics: architecture (e.g., financing and collection methods), context (e.g., jurisdiction population, density, and wages), and performance, both economic and materials collection. A comparison of systems in Europe and North America with different system architectures and contexts illuminates the importance of using the methodology to discern the extent to which architecture and context drive system performance.IntroductionElectronic waste (e-waste) recycling offers several environmental benefits when processing is done responsibly. The controversy around e-waste recycling systems rarely debates such benefits; rather, it focuses on the characteristics of an effective system and whether benefits outweigh costs. Historically, the costs of recycling most electronics have outweighed the value of the scrap recovered. Thus, in the absence of legislation, e-waste recycling systems have been limited to private recycling of high-value waste with minimal consumer participation. E-waste recycling systems now exist in many locations worldwide including Asia, the European Union, Canada and the United States and the amount of related legislation continues to increase. Numerous approaches have been proposed including landfill bans, extended producer responsibility (EPR) and consumer advance recovery fee (ARF) funded recycling systems."

Jan 1, 2008

By S. Viswanathan, Q. Han, A. S. Sabau

"In spite of recent advances in the mathematical modeling of fluid dynamics for materials processing applications, no significant advances have been made in the numerical discretization of these equations. In this work, the application of two-step projection methods for the numerical simulation of interdendritic flows is discussed. Unlike previous methods, the methods presented here are constructed for the exact equations which are characterized by variable density and volumetric fraction of the liquid. The drag terms, which describe the momentum loss due to the flow around and through the dendrite structures, are treated implicitly. Numerical examples for shrinkage-induced flow during solidification of an Al-4.5% Cu alloy bar is used to illustrate the effectiveness of the proposed algorithm.IntroductionLiquid contraction during solidification plays an important role in the formation of casting defects such as shrinkage voids, microporosity, and macrosegregation. Owing to their importance, the study of transport processes during solidification have received considerable attention during the past years [1, 2]. By the use of volume-averaging techniques, the mass and momentum equations for flow through a stationary dendritic structure were derived [3]. By using the volume-averaging techniques for multi-phase systems, two-phase transport equations for solidification problems were derived [4]."

Jan 1, 1999

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can' be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

By Liugen Sun, Xingming Jiang, Weijiao Yang, Yihang Hu, Yongqiang Yang, Hua Wang

During the past decades, cyclone electrowinning (CE) has been regarded as a novel separation technology, which can be used for direct electrowinning of metals from low concentration solution. Recently, CE was proven effective for the treatment of antimonic gold concentrates. The experimental results of cyclone electrowinning of antimony show the current efficiency increases from 43.8 to 72.2% with the increasing current density (from 254.8 to 647.3 A/m2), and on the other hand, power consumption per ton antimony decreases from 6100 to 4200 kWh with the aforementioned increasing current density. The grade of the obtained cathode antimony could reach 98.6%. Compared with the traditional electrowinning using parallel-board electrodes, the economic profit of CE was 33.1% higher attributed to the high current efficiency of CE. In addition, CE could adapt to high current density. All these characteristics indicate the CE method can be implemented commercially for processing antimonic gold concentrates.

Mar 1, 2018

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc, Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed,

Jan 1, 2003

By Zeyun Cai, Gaoyang Song, Bo Song, Yuhou Yang

In this research, super gravity field was introduced in the solidification process of high carbon steel. The experimental results show that the solidification structure of Fe–1 wt% C steel can be largely refined by applying super gravity at the cooling rate of 10 °C/min. Both the primary and secondary dendrite length was markedly reduced. In addition, the eutectic structure in the inter-dendrite was also refined with the obvious reduce of eutectic space. However, the macro-segregation of C along the direction of super gravity was caused with higher weight percent at the upper area than that at the bottom of the sample. The mechanism of solidification structure refinement and the C macro-segregation of Fe–1 wt% C steel in super gravity field were also discussed in this paper.

Mar 1, 2017

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Gjergj Dodbiba, Atsushi Shibayama, Toyohisa Fujita, Takashi Shikazumi, Yukio Kato, Kenji Murata

"A new crushing or liberation technique by means of underwater explosion is put forward. This technique is suitable for crushing and liberating various materials, for instance: the electric parts of the discarded portable telephone, CPU from mother-boards of PCs, steel from plastics tubes used as construction materials, waste constructed materials like panels, tungsten carbide scraps, as well as slitting the optical disk (e.g. DVDs), etc. The materials to be crushed are immersed in water and then the explosion is carried out by using only a small amount of explosive. The shock waves in combination with the generated bubbles are very effective in liberating the materials of different densities. It was observed that the metals crushed or liberated by using this technique were leached much faster when compared with the conventional crushing technique. This crushing method can be applied for liberation of many kinds of electric or mechanical tools. Introduction The explosive has been used since Nobel’s invention in 1866. The main practical application of explosion is in the large scale public works, such as dam construction, land development, tunnel, mining and dismantlement of building. The shock wave caused by explosion extremely can generate high pressure able to break the concrete and rock, and other materials. In this study, the crushing and liberation of waste materials was carried out by explosion in water. The idea was to use this technique as a pretreatment stage prior to recycling. The explosion in water can be used to crush hard materials, helping the liberation between different attached materials. The samples used in this experimental work are waste materials such as construction materials, hose, cemented carbide, cellular phone, lithium buttery, DVD-R, etc."

Jan 1, 2008

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By Shawn A. Cefalu, Matthew J. M. Krane, Kent J. VanEvery

"Segregation during electroslag remelting (ESR) of a nickel-chromium-molybdenum alloy (Ni-8 wt% Cr-25 wt% Mo) has been modeled. Features of the model include species transport and AC electromagnetic effects coupled with fluid flow, heat transfer, and solidification. The effect of varying ingot diameter and melt rate, on macrosegregation patterns, local solidification time, and liquid pool profiles obtained from this model are demonstrated. The results show that the macrosegregation in the ingots correlates to the filling velocity.IntroductionElectroslag remelting (ESR) is a secondary melting process used to refine the chemical composition and the microstructure of metals. Macrosegregation of solute elements causes defects in ESR ingots, including freckles and the maldistribution of phases. These defects are not correctable through heat treatment due to the large length scales over which they occur. However, the frequency and distribution of these defects may be minimized, or even prevented, through process control based on an understanding of the conditions that lead to their formation.In the past, studies have been conducted on the effect of the process parameters on the shape of the melt pool and the thickness of the mushy zone [1-7]. In these studies, the shape of the liquid pool is determined by consideration of the heat and fluid flow induced by electromagnetic (Lorentz) force and thermal buoyancy. The transport of solute and the resultant solutal buoyancy effects were not considered in these macroscopic models. Defect formation is tied to formation of secondary phases (e.g., freckling and white spots in nickel superalloys) [5,8]. In cases where secondary phase formation is calculated (e.g., [6]), phase fractions are determined using a micro-scale model given the local solidification time (LST) and local thermal history from the macroscale model.Using the local thermal history from the macroscopic transport model to predict microstructure increases the importance of the accuracy of those results. This investigation models the macrosegregation of molybdenum during the ESR of a Ni-Cr-Mo alloy. The effect of macrosegregation on pool shape and depth is demonstrated, along with its effect on the local solidification time. By comparing the relative effects of the melt rate and ingot radius, a better understanding of the factors that affect macrosegregation, and ultimately secondary phase formation may be obtained."

Jan 1, 2004

By G. S. Victorovich

Technical progress in primary smelting has changed the face of the copper industry in the years since the Second World War. Much of this change has resulted from a wide acceptance of flash smelting technology. In addition, research has been directed toward devising converting processes to replace conventional Peirce-Smith converting technology. One major thrust has involved a revival of the old " ", idea of oxygen flash converting of comminuted mattes. This paper reviews the 60-year history of flash converting. Particular attention is paid to Inco's investigations into the processing of white metal containing significant amounts of nickel and, in some cases, iron. Thermodynamic analysis and laboratory experimental results are presented which throw light on the behaviour of nickel and other salient features of flash converting. The possible role of oxygen flash converting in the copper pyrometallurgy of the future is briefly discussed vis-a-vis direct production of copper.

Jan 1, 1993

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001