Search Documents

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

By Charles I. Richman

Aquispirillum magnetotacticum (AM) is gram-negative hetrotrophic bacteria that belongs to a class ,of magnetotactic bacteria that have an ecological niche in marine marches and fresh water swamp sediments. Thiobacillus Ferrooxidans (TF) is a Gram-negative, acidophillic chemoliths that may have similar chemical conditions within the cytoplasmic membrane as Aquaspirillum M. to support growth of Magnetosomes. Magnetosomes are cellular bodies that accumulate under slightly aerobic conditions. Magnetotactic motion occurs in an external magnetic field and depends on the medium viscosity. The Atomic Force Microscope equipped with a magnetic tip shows the presence of Magnetosomes in these bacteria strains. The size, shape of magnetosomes in AM and TF strains are characterized.

Jan 1, 1998

Acid generation from reactive sulphide mineral tailings has become a major environmental problem in the mining industry. Initiation of chemical and biochemical oxidation reactions of the sulphide mineral leads to acid generation. A novel concept of safe disposal and utilization of reactive fine mill tailings is presented in this paper. The paper also presents the results of a preliminary laboratory experimental .study of the concept. The tailings are agglomerated using portland cement as a binder. The cold bonded agglomerates are encapsulated with other chemical additives to act as acid neutralizers, oxygen and ironoxidizing bactericides., The primary. factors influencing the choice of bacterfoides to inhibit the acid generating bacteria are their costs, toxicity and environmental friendliness. The paper discusses the utilization of agglomerated' products as aggregates for underground backfill, or as gravel for surface land cover.

Jan 1, 1991

By Katsukiyo Marukawa, Manabu Iguchi, Sigeta Hara, Shinichiro Yokoya, Sigeo Takagi

"A numerical analysis and water model study of the mold region of a continuous casting apparatus was performed with a novel injection concept using swirling flow in the pouring tube, to control the heat and mass transfer in the continuous casting mold.As a result, the following results were found:1) By changing swirl strength, it is easy to control the flow pattern as well as the direction of the flow.2) Uniform velocity distribution can be obtained within a very short distance from the outlet of the nozzle.3) Heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl.4) Swirl helps the superheat in the melt dissipate.S) Penetration depth of nozzle outlet flow is decreased remarkably by the application of swirling.6) For the case without swirl, the peak of the flow moves near the mold-wall with flowing down from the outlet of the nozzle due to the Coanda-effect. On the other hand, peak of the flow moves near the mold axis with flowing down from the nozzle-outlet within considerable short distance, namely axi-symmetric velocity distribution can be obtained within very short distance from the nozzle-outlet.Those findings mentioned above are very useful to control the flow pattern in the billet and bloom continuous casters."

Jan 1, 2001

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By Dan Michaelsen, Warwick Stewart

"PT Kaltim Prima Coal (KPC) is a large-scale truck and shovel operation mining thermal-coal in East Kalimantan, Indonesia. The operation produces 15 million tonnes of coal and mines over 120 million bank cubic metres of overburden annually. Approximately 35 percent of the waste rock is classified as potentially acid forming. Acid drainage must therefore be managed to prevent acid formation from spoil dumps and mined-out areas.KPC aims to prevent acid production in dumps by covering potentially acid forming spoils with materials identified as non acid-forming. The covers, built to engineering standards, minimise the flux of oxygen and water to pyritic spoils, thereby controlling the oxidation reaction, and reducing ARD discharge to negligible rates. Cover designs and cover materials vary according to stability, materials availability, equipment availability, and cost effectiveness. A modified field net acid generation (NAG) test procedure has been developed at KPC to identify and segregate overburden geochemical types. This paper discusses the ARD management strategies and operational procedures adopted by KPC to manage potentially acid forming waste rock. The development and field application of the NAG procedure at KPC is presented in a companion paper. Analytical"

Jan 1, 1999

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70' s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By Michael P. Meisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halo¬gens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By S. C. Sharma

The aluminium matrix composites with ceramic dispersoids can be separated by density difference concept. In the proposed work composite scrap is recycled using an oil fired furnace. The scrap is melted in the furnace and temperature is maintained below 740 degree centigrade. Because of the density difference the lighter dispersoids will float and heavier dispersoids will settle down. The clean melt is separated be removing the floating and settled disperssoils, and then filtering using ceramic filters.

Jan 1, 1995

By Junji Shibata

Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal salts by using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versa tic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxalate powders obtained in this process. The analysis by using EDX showed that the two metal oxalates were distributed uniformly at the same ratio as the organic phase composition.

Jan 1, 2001

By S. K. Varma, Miriam Regalado, Daniel Salas, Erica Corral, Erika Esquivel

"Age hardenable 2014 aluminum alloys and composites containing 0.10 and 0.15 volume fractions of alumina particles (VFAP) have been solutionized at 540 and 550°C for up to 20 hours. The solutionized samples, heat treated for 5 and 20 hours, have been subjected to room temperature rolling until cracking develops. The work hardening curves have been compared to determine the effect of solutionizing time on the rolling characteristics from both hardness and the microstructural evolution points of view. Solutionizing at two different temperatures results in differences in the extent to which the composites can be rolled until fracture. The microstructural characterization by TEM has been performed to understand the room temperature rolling behavior.IntroductionThe effect of solutionizing on the age hardening response of 6061 and 2014 aluminum alloys and composites reinforced with 0.10, 0.15 and 0.20 volume fractions of alumina particles (VFAP) have been reported in the literature [1-4]. A comparison of the monolith and composites indicates that particles promote the aging process through differences in the microstructures in solutionized condition. The first effect of solutionizing is to produce a grain growth process which follows a grain growth law (square of grain diameter as a function of solutionizing time). It appears that it is possible for vacancies to be emitted during grain growth period as they try to minimize the total grain boundary surface area by increasing their diameter. This may be common to both the monolith and the composites. However, the second effect must be exclusively considered for the composites. The particles generate dislocations during the solutionizing process due to the differences in the values of the coefficient of thermal expansion (CTE) between the particles and aluminum base metal. It has been determined [1] that the dislocation density increases with increase in solutionizing time in the composites of 6061 aluminum alloys reinforced with 0.10, 0.15 and 0.20 VFAP. The improved bonding between particles and matrix can give rise to additional generation of dislocations due to curvature effects [1] with the result that the dislocation density continues to increase with increase in solutionizing time even after the CTE effect is considered to have been stabilized."

Jan 1, 1998

By J. N. Kondo, M. Hara, T. Smida, N. Ooto, K. Domen

"A porous material composed of two-dimensional anionic sheets of a layered perovskite, KSrNb30 10, was studied as photocatalyst for the production of Hz in the presence of alcohol sacrificial donors. Colloidal single and multi-layered HSr2Nb30 10 sheets were formed by intercalating ietra(n-buthylammonium) cations into the interlayeres of H+-exchanged KSr2Nb30 10 (HSr2Nb30 10), and addition of HN03 solution to the colloidal suspension precipitated the porous materials in which HSrNb30 10 sh~ets rand~mly stuck together. Original HSr2Nb30 10 before exfoliation had a BET surface area of 1 m2 g-1, whereas the surface area of a porous material prepared under optimal conditions exceeded 100 m2 g-1. The porous HSr2Nb30 10 had considerably higher photocatalytic'activitie8 for oxidation of 1-propanol and 1-buthanol than HSr2Nb39io, indicating that in the porous materials many niobate sheets are available for decomposition of these large alcohols.IntroductionQuite a research effort has gone into the design and study of porous materials. Such materials with large surface areas would have applications in highly efficient adsorbents or catalytic reactions.We have been studying photocatalytic reaction by cation-exchangeable layered metal oxides, where alkali metal cations are intercalated into the interlayers of inorganic sheets.[1,2] There are several advantages to using layered compounds rather than bulk powders for photocatalysis. Layered compound is rich in variety, in addition, modifications of them are easily performed by exchanging alkali metal cations in the inter layers for H + or other metal cations. The most important advantage is that some layered compounds have considerably high photocatalytic activities than bulk catalysts because the electrons and holes generated in each thin inorganic sheet readily reach interlayer spaces as reaction sites at the illterlayer spaces. It should be very important for further improvements· of layered photocatalysts to utilize two-dimensional inorganic sheets effectively."

Jan 1, 2000

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By K. P. V. Lei

The U.S. Bureau of Mines investigated a hydrothermal sulfidation procedure to recover lead and silver from plumbojarosite. The plumbojarosite, generated during pressure-oxidative leaching of zinc concentrate in a commercial operation, contained, in percent, 25.4 pb, 18.8 Fe, 1.4 Zn, 29.5 SO,2-, 3.2 s?, 13.4 total sulfur, and 7.4 oz/ton Ag. The sulfidation was conducted in an autoclave and converted the plumbojarosite to amorphous iron oxide and liberated the lead and silver as sulfides. The best operating conditions were using 50 9 of plumbojarosite and 7 pct s? (2.04 9 S? added) in 500 mL of 2.0 mol/L NH3, 150? C, and 1 h. The sulfidation product contained, in percent, 37 Pb, 28 Fe, 6 S2-, 2 SO,2-, and 11.2 oz/st Ag. Ferric chloride leaching extracted 98 pct Pb and 97 pct Ag from the sulfidation product.

Jan 1, 1990