Search Documents

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By Yang Tian-zu

Sodium pyroantimonate which is widely used as the clarifier in the glass industry and as the synergist in anti-flaming industry respectively has a production history of about 30 years in China. At present there is the production capacity of about 20,000 tons per year in China and China is chief producer of sodium pyroantimonate. In this work the production processes adopted by the producers of China, the operation conditions and the product qualities of sodium pyroantimonate prepared by different preparation methods have been summarized, and on the basis of comparing the advantages and disadvantages for each process the most advanced method - the air-oxidation method was introduced in detail. The production processes of sodium pyroantimonate mainly include the method of oxidation by sodium nitrate, the oxidation method of hydrogen peroxide, the potash salt method, the chlorination method and the air-oxidation method etc. The method of oxidation by sodium nitrate in which the crude antimony oxide, sodium carbonate and sodium nitrate are separately used as the raw material, the flux agent and the oxidant, has the advantage of short and simple technological process, but low grade quality of sodium pyroantimonate and bringing about serious environmental pollution are the disadvantages and this method has been substituted by other methods. Sodium pyroantimonate can be directly prepared by the hydrogen peroxide oxidation method with the advantages of simple technological process, high grade quality of the product and little environmental pollution. High grade quality of sodium pyroantimonate can be also synthesized by the potash salt method, in which industrial antimony white, the hydrogen peroxide, potassium hydroxide and sodium hydroxide are applied as the starting material. The disadvantages of these two preparation methods are high production cost and high requirements on the raw materials. The chlorination method with the crude antimony oxide, hydrochloric acid and chlorine as the raw material has the advantages of low production cost and high grade quality of the product. However complex process, high requirement of anti-corrosion for the equipments and producing plenty of waste water limit its application. The air-oxidation method with stibnite/jamesonite concentrate, sodium sulfide, and sodium hydroxide as the raw material and atmosphere as the oxidant is a newly developed method and its advantages are low production cost and the complex raw material can be treated by this method and its disadvantage is that the quality of sodium pyroantimonate is lower than that prepared by the oxidation method of hydrogen peroxide and the potash salt method.

Jan 1, 2006

By William James Middleton

The life-cycle assessment (LCA) approach can be an important tool for the quantification and evaluation of environmental impacts associated with metal production systems. At the conceptual phase of a new metals development project, LCA can: ? Aid project decision making by evaluating the environmental consequences of design decisions ? Support project permitting and reinforce site/process environmental impact assessment ? Allow environmental impact comparisons between alternate flow sheets For existing metals production systems, LCA has been used to aid targeted process improvements by monitoring recent historical trends in environmental performance, either through local or external (externalities) process improvements. This paper discusses the life- cycle assessment methodology, and its application as a supportive tool for environmental decision-making in process design and operation, and for site environmental impact assessment and permitting. Selected examples from a recent LCA performed on the Pressure Acid Leach Process for treating nickel Laterite ores are employed to demonstrate the usefulness of the tool.

Jan 1, 2004

By Yavuz Ali Topkaya, Aydin Rusen

"In this study, zinc and lead recovery from zinc plant leach residue obtained from Çinkur using hydrometallurgical methods have been investigated by laboratory scale experiments. Considering more than one million tons leach residue (LR) rich in Zn (12.43%) and Pb (15.51%) in the stockyard and environmentally hazardous, it is essentially necessary to process Çinkur LR. Zinc and lead have been recovered in two main stages. As a first step, Çinkur LR was releached by using hot sulphuric acid for zinc recovery. About 72 % Zn was recovered by using 150 g/l H2SO4 at 95 oC in 2 hours with a pulp density of 200 g/l. Secondly, for lead recovery brine (NaCl) leaching tests were performed on the secondary Çinkur LR obtained after acid leaching process. In brine leaching while lead recoveries up to 95 % could be attained at a low pulp density, the maximum recovery obtained was 84.9 % at a high pulp density (200 g/l) with 300 g/l NaCl concentration in 10 minutes at 95 oC. Introduction Zinc and lead have been known and used by humans since ancient times and also they are important nonferrous metals [1]. Zinc and lead have different properties thus they are used in various application areas, ranging from automobiles to construction, from batteries to textile. Zinc and lead deposits are widely distributed in the Earth’s crust. The principal ore mineral for zinc is zinc sulfide, Sphalerite (ZnS), and lead sulphide, Galena (PbS), is the main source of lead in the world [2].Although zinc is generally produced from sulphidic ores (ZnS) or concentrates by Roast – Leach – Electrowinning (RLE) in the world, in Turkey, zinc production is based on zinc carbonate ores (ZnCO3), and at the Çinkur plant zinc was produced from zinc carbonate from its establishment to 1997 due to high reserves of zinc carbonate in that region. Çinkur is the only plant in Turkey that produces Zn from primary ore containing ZnCO3 by Waelz – Leach - Electrowinning route [3]. However, due to depletion of local high grade ores, oxidized ore concentrates were imported from Iran after 1997, until this plant was shut down. Therefore, there are two different leach residues (LR) which are Turkish LR (TLR) and Iranian LR (ILR) in Çinkur stockpiles. It has been estimated that the total amount of leach residue is more than one million tons of which the major part is Turkish leach residue (TLR)."

Jan 1, 2008

By T. A. Edison

A distinct hydrocarbon maturation anomaly coincides with the Gold Acres open pit, Nevada (Figure 1). Both atomic hydrogen to carbon (H-C) ratios and reflectance measurements of contained organic matter indicate significantly higher maturity in samples collected within the confines of the open pit than in samples from the surrounding region (not shown in Figure 1).

Jan 1, 1987

By Keizo Uematsu, Satoshi Tanaka, Zenji Kato, Nozomu Uchida

"A novel technique is developed and applied to evaluate the binder segregated at the· surface of granule. Compressive strength of each granule was measured directly with a micro-compressive instrument. The relation between compressive characteristics and the amount of binder was discussed quantitatively.IntroductionCharacterization of granules is essential in the production of ceramics, since they govern the structure of green compact and thus the structures and properties of ceramics. However, there is no research to clarify the relation between the strength of granules and structure of granules, especially of binder segregation at granule surface. We develop a novel technique to determine the binder concentration in the granules by the iodine method. In this study, we measure yield strength of granules directly and discuss the relevance between compressive characteristics and the concentration of binder.ExperimentalGranules were prepared by spray-drying of aqueous slurry of commercial alumina (AL160-SG1. Showa Denko, Tokyo, Japan) and PVA (PVA 105 Kurare, Japan). PVA. concentration in granules was 1.1, 1.5 and 2.3 wt%. The inlet and outer air temperatures were 200 and 95 °C , respectively. Iodine-potassium iodide solution was prepared by dissolving iodine (0.15mol) and potassium iodide (0.15mol) in diluted water (50ml). A saturated boric acid solution was prepared by mixing boric acid powder with a diluted water."

Jan 1, 2000

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By Hiroki Kumakura, Kotaro Seki, Takashi Nagai, Masahito Abe, Daiki Noguchi

A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. PGM in the catalyst are supported by ceramics for four-wheel vehicle or metals such as stainless steel for two-wheel ones. The recycling process of PGM from the metal-supported catalyst has not been developed, while the process for ceramic-supported catalyst was developed, such as Rose process. We designed a noble recycling process of PGM from metal-supported catalyst using complex oxides between PbO and PGM oxide. In this study, complex oxides, PbPt2O4, PbPdO2, PbRh2O4 and so on were synthesized at about 773–973 K. And the dissolution behavior of these compounds to hydrochloric acid was investigated. PbPt2O4 and PbPdO2 were dissolved to hydrochloric acid easily, but PbRh2O4 was not.

Mar 1, 2017

By Bernd Kos

The management of waste materials in the aluminum industry is as important as in other basic industries. Due to the high value of the-by products of the melting process and their toxic properties we took the challenge to develop a process technology to reduce the environmental impact and to help industry to get a better yield of their by products/raw materials. In melting operations metal losses due to oxidation are nearly unavoidable, the amount of such losses, however, can be controlled. Aluminum dross actually is a by product and any shop would like to get rid of it in the most economic way. This by product still contains up to 70% valuable metal! In the present work we describe possibilities to separate metal and residues for further processing. Recycling of metal concentrates, selling of dross and dumping of the residues have been the typical solutions up to now. But there are technologies available which are designed to reduce the waste to a minimum or even avoid it altogether. Such alternatives are processing of the dross into materials which can be reused in other industrial processes in order to avoid any dumping. This can be done by separating the metal and the residues by centrifuging and further use of the residues in the chemical or refractory industry. ECOCENT means economical and ecological recovery of aluminum by centrifuging of hot dross. This process, developed by FOCON Austria, is based on the idea of treating the hot dross as quick as possible in a single operation to avoid exothermic losses, intermediate storage and unnecessary handling as well as to save energy. In the ECOCENT process the hot dross is fed without any fluxing salt additions into a converter where the relevant parameters for separation, like temperature and viscosity, will be adjusted. Further big lumps of dross are ground into smaller pieces in order to improve the later separation of the metal. After homogenizing and adjusting the temperature, the hot dross is poured as quickly as possible into a centrifuge. In the ladle or alternatively the mould of the centrifuge the centrifugal forces are used for the separation of aluminum from aluminum oxide, the major constituents of dross. The separated pure metal can either be discharged liquid or as solidified aluminum ring. The design of the device for the production of liquid or solid metal is almost identical. As soon as the centrifuging is finished the liquid aluminum can be poured back into the furnace or can be used for ingot pouring. After the pouring of the metal the "dry" residues are removed just by turning the ladle. Alternatively the aluminum solidifies in the mould and is discharged as a compact ring. The separation of the residues from the aluminum ring is automatic. Due to the batchwise operation the composition of the metal is the same as in the skimmed furnace of origin. The complete treatment cycle needs about 40 minutes. The recovery rate of aluminum is better than 90% of pure metal. This technology is highly flexible by its nature and can easily accomodate various operational requirements. The consumption of energy is more than 50% lower compared to conventional dross processing as the ECOCENT process is using the inherent energy of the hot dross. These extremely good results are not dependent on the aluminum content of the dross even from very dry dross most of the metal can be recovered. The main advantages compared to conventional dross processing are the high recovery rate, the known analysis of the metal and the immediate reuse of the recovered aluminum. The high recovery rate and the pure metal result in a short amortization period. The compact ECOCENT unit needs a minimum of space since extensive handling can be avoided. The electronically controlled process needs no cooling water and is simple, safe and environmentally sound. The residues are free of fluxing salts, their content of metallic aluminum is low and the environmental problems are thus greatly reduced.

Jan 1, 1995

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By Lichao Ding, Chunhua Liu, Yunnen Chen

"In this paper the simulated acid magenta dye discoloring the reaction process was researched. The results showed that it attained highest decolorization efficiency for acidic magenta simulation dye wastewater when pH 9 and reaction time 10 min. With the initial dye wastewater concentration increased, the decolored rate decreased. The decolored rate in general kept a tendency to increase with the temperature increased. Kinetics researches showed that when pH 9, reaction temperature 20 and 35 ?, the decoloring reaction process for the dyes accorded with the First-order dynamic equation. The decoloring reaction rate constant was influenced by initial concentration of dye wastewater and temperature.1. IntroductionIn China, textile printing and dyeing industry is one of industrial departments which using more water and discharging more wastewater. There is about 7 billion tons of waste water discharge each year, of which 80% from the process of printing and dyeing. Being complex ingredients, high chroma, more toxic substances and severe environment pollution, the treatment of printing and dyeing wastewater becomes problem urgent to be resolved. The traditional treatment methods such as adsorption [1], coagulation [2], biochemical method [3,4], which has advantages of simple equipment, simple operation and mature process, but they can cause waste accumulation and secondary pollution [5,6].Magenta is a kind of organic compounds, which classified into acid and alkaline magenta. Considering the advantages of simple operation, low cost, simple experiment equipment and friendly to environment, acid magenta dyes wastewater was chose as object in this paper. Some parameters such as pH, contact time, temperature and the initial concentration on of simulative acid magenta dyes wastewater were studied."

Jan 1, 2012

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Larry B. Fiske

Elimination of dust and processing of fines for both thermal and metallurgical coals is addressed. The efficiency of treatment with lignosulfonates compares favorably to oil in thermal coal. Effect of treatment with various lignosulfonates upon cokability of metallurgical coal was determined by Free Swelling Index, Gieseler Plasticity and Arnu Dilatation.

Jan 1, 1992

By Roger Agnew

Sulphide ores mined by Inco Limited in the Sudbury District contain small quantities of cobalt. During beneficiation, cobalt distribution to various streams is similar to nickel. After smelting, nickel is selectively extracted by carbonyl refining and the cobalt remains in the carbonylation residue. This residue is processed in a specialized hydrometallurgical plant to produce precious metal residues, copper cathodes, and a nickel- cobalt carbonate intermediate product. The nickel-cobalt is shipped to Port Colborne where the cobalt is separated as cobaltic hydroxide and refined to metallic cobalt. This paper deals specifically with the recently constructed Electro Cobalt Refinery. The cobaltic hydroxide is dissolved and residual zinc, copper and nickel are removed by ion exchange and organics by a carbon column. The purified cobalt solution is fed to the electrowinning circuit where cobalt rounds are produced on stainless steel mandrels. In the design and construction of the refinery, special attention was directed to materials of construction both for the process equipment and the physical plant, operating control and flexibility, and the quality of the working environment. The end result is an efficient and clean operation which yields a product of excellent quality.

Jan 1, 1988

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By Thomas Niehoff

"Oxyfuel combustion systems are state of the art for many melting operations. Airfuel systems have been stepwise modified to oxygen enrichment, oxygen lancing and oxyfuel. Every change of the melting process will have consequences with regards to emissions and energy usage. The uniqueness of many operations requires unique skills to resolve potential issues. This paper will give some examples of how airfuel systems can successfully be converted to oxyfuel.IntroductionOxyfuel technology – meaning the combustion of fossil fuels such as natural gas, oil or coal with technical oxygen instead of air for industrial melting or heating processes is widely used in many industries these days. Even though oxygen production, storage and handling has been state of the art for decades other opinions exist. Often oxyfuel is regarded with fear and potential hazards like: “Oxygen makes the process too hot.”, “Oxygen will melt away the refractory.”, Liquid oxygen is dangerous.”, “Oxygen will cause explosions.”, ……etc.Typically a more detailed discussion about a specific industrial process and how oxygen can be applied in a safe and economic way the seeming issues go away."

Jan 1, 2010

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012