Search Documents

By Arthur G. Hunt

Smelting using the direct-to-blister process commenced at Olympic Dam on 31 July 1988. The unique nature of the Olympic Dam ore body led to the selection of the direct to blister smelting process. Significant improvement in the design of the furnace and the understanding of the fundamentals of the process and its operation has occurred in the 10 years of operation. The paper will discuss the operation of the #1 Smelter and the design, preparation for start up and early operating experience of the #2 Smelter.

Jan 1, 1999

By Kazuki Morita

Dissolution mechanism and solubility of chlorine in the oxide melts, such as CaO-SiO2-Al2O3 (-Na2O), Na2O-SiO2-Al2O3 and CaO-SiO2-FeO systems, have been equilibrium technique was employed with controlled Po2 and PCl2, (Po2 = 10-6 -10 19 atm, PCl2 10-6 -10-13 atm at 1673-1748 K). The solubility of chlorine in the 40mass%CaO-40mass%SiO2- 20mass%Al2O3, slag was found to vary in proportion to Pb2/ w and pc/z/p' which proved that chlorine dissolved in the melts as C1 anion. Hence, the chloride capacity (CCI-), indicating the ability of molten oxide to absorb chlorine, has been defined as; The Ccl value was observed to increase with increasing slag basicity and temperature, and showed a reasonable relationship with that Of CS2-. Based on the result obtained in the present study, chlorine distribution during incineration with slags was predicted quantitatively.

Jan 1, 2003

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By Youn-Bae Kang

Evaporation mechanism of S from liquid Fe–C–S alloys at 1873 K was proposed by analyzing available experimental data. It has been known that increasing C content in liquid alloy increases activity coefficient of S ðfSÞ, and it could raise driving force for the evaporation reaction S = S(g). However, experimental data of the evaporation of S in the Fe–C–S alloys could not be accounted for only by considering the increases of fS. In the present study, formation of carbosulfides, CS(g) and CS2(g), was additionally taken into account in order to explain role of C for the accelerated S evaporation. Surface adsorption of S was also taken into account, which retards the evaporation rate of S. An evaporation model equation was formulated. It can be applied to calculate the evaporation rate of S over wider C content (from zero to its saturation to liquid alloy).

By M. Firdaus, M. A. H. Shuva, M. A. Rhamdhani, G. A. Brooks, S. Masood, M. A. Reuter

Declining grade of primary ores and resource efficiency have led us to process more alternative metal resources such as e-waste. One of the processing routes for extracting valuable metals from e-waste is through the black copper smelting. However, the underlying knowledge of the thermodynamics behaviour of the valuable metals contained in e-waste during smelting are limited which prevent us from developing an optimised process to recover all the metals. These different metals clearly will have different favourable conditions for their extraction. To illustrate this, the distribution behaviour of germanium (Ge) and palladium (Pd) between liquid copper and ferrous-calcium-silicate slag during black copper smelting was analysed. It was demonstrated that oxygen partial pressure and slag composition affect the partitioning of these metals to the copper phase and the favourable slag chemistry for recovering these metals is opposing. Considering the available thermodynamic data of these metals, an analysis for the optimum conditions is presented.

Mar 1, 2017

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997

By Darrin Wikoff

"The data, compiled by the Department of Energy (DOE), indicates that the average industrial plant could reduce its total energy cost by 14.8% by implementing effective Life Cycle Asset Management processes. The actual savings varies by industrial classification, but in all cases the potential is substantial and could have a marked impact on the operating profit of the company.Improvements geared towards improving equipment reliability have distinctive linkages to environmental performance, such as reducing the amount of product and raw material waste through routine monitoring of system parameters through predictive technologies, and preventing interruptions to production cycles with a focus on Overall Equipment Effectiveness (OEE).Alcoa successfully reduced solvent disposal costs by more than 40% and GE reduced greenhouse gas emissions by more than 250,000 metric tons. This presentation will show you how companies have successfully reduced energy and disposal costs through a focused effort on manufacturing process reliability.IntroductionSmelter in the ParkThe quaint town of Portland, Victoria protrudes outward towards Antarctica from Australia’s southeastern coastline. Portland is a quiet rural community surrounded by agriculture that draws tourists by the thousands to the southernmost edge of Victoria by way of breathtaking cliff top views of the majestic Southern Ocean, the intrigue of shipwreck coves along the Great Ocean Road, and what most will call the eighth wonder of the modern world, the “Smelter in the Park”. Integrated within Portland’s beautiful landscape is a 356,000 ton/year aluminum smelter that stands as a symbol of collaboration between nature and industry. Nestled atop a ridge which faces “Sail Rock”, a popular destination of local and visiting fisherman, the smelter is engulfed in a mix of brush and wetland preserves that are home to many of Australia’s feathered and fourlegged natives. Also within its interior you’ll find parks and natural landscapes abundant where man and machines coexist with the native inhabitants."

Jan 1, 2009

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By B. Farouk, D. Apelian

"A numerical model has been developed to predict the temperature history of particles injected in a low pressure d.c. plasma jet. The temperature and velocity fields of the plasma jet are predicted as a free jet by solving the parabolized compressible Navier-Stokes equations using a spatial marching scheme. Particle trojectories and heat transfer characteristics are calculated using the predicted plasma jet temperature and velocity fields. Correction factors have been introduced to take into account non-continuum effects encountered in the low pressure environment. The plasma jet profiles as well as the particle/plasma interactions under different jet pressure ratios (from underexpanded to overexpanded) have been investigated.I. IntroductionIn the plasma spraying process a d.c. plasma jet is used as a heat source to melt and accelerate powder particles which subsequently impinge and solidify on a given substrate. During low pressure plasma deposition (LPPD) prooess, the plasma jet is expanded into a low pressure environment (40-80 Corr) which results in high plasma jet velocities with Mach numbers ranging from 2 to 3. Previous efforts to predict heat transfer and fluid flow in plasmas have made use of incompressible flow formulation employing turbulence models [1-3] for atmospheric plasma spraying. However, these theoretical calculations have been limited to the subsonic flow regime; hence, the compressibility effects and viscous heat dissipation were neglected. In the LPPD process, the plasma jet is operated at the supersonic flow regime, therefore, the compressibility effects and viscous heat dissipation are no longer negligible. This is the main motivation of this work.In addition, production of high quality dense deposits requires that a large fraction of the injected particles be in a molten state when they impact the substrate. An additional motivation for this work is that it is important to understand the plasma/particle heat and momentum transfer since these phenomena dictate both the particle thermal history and particle trajectory.Early computational works in supersonic nozzle field flow [4,5,6] consisted of patching methods that divided the flow field into an invisoid free stream and a viscous boundary and. mixing layers. Each was analyzed independently and coupled through appropriate boundary conditions. Later schemes [7,8] involved solving time-dependent, compressible Navier-Stokes equations over the entire computational domain. These schemes show a great promise in predicting flows with complex structure, and where the viscous effects became prevalent."

Jan 1, 1986

By Corby G. Anderson

Laboratory testing, interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid optimization of laboratory testing and operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing, this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.

Jan 1, 2006

By Rauf Hurman Eric

In this review paper the effect of composition and temperature on electrical conductivity and viscosity of the slags encountered in electric smelting of PGM-containing sulfide concentrates is described along with their liquidus temperatures. Optimization of slag composition is attempted on the basis of opposite trends of viscosity and electrical conductivity. Metal losses to slag, matte-slag separation and matte settling are also discussed in conjunction with interfacial and surface tension concepts. The electrode immersed in the slag phase is the main factor in the design and operation of the furnace. The most important electrode parameters are the size and the positioning in the slag phase which are determined by the slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles within the slag phase which in turn affects the flow conditions. Thus the flow of slag is discussed together with furnace geometry, stirring action, buoyancy and electromagnetic effects and the action of the electric furnace as a settler is emphasized. A discussion on the design d production capacity of the furnace is provided which are based on considerations derived mainly from slag properties.

Jan 1, 2006

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

At the present time, cyanide is the most widely used reagent to extract gold from its ores and concentrates. However, its use in mining has become the focus of intense attack by various groups throughout the world; as a consequence, a renewed effort has been launched to find suitable alternative lixiviants to recover gold. Chlorination was the most popular process to extract gold, before it was rendered obsolete with the advent of the cyanidation process at the turn of the last century, not least because it required the use of potentially hazardous and costly chlorine to oxidize/complex the gold. The PLASTOL® process, originally designed to recover the platinum group metals (PGM?s) from their ores and concentrates, provides an alternative to cyanide for gold ores. The process generates oxidizing conditions in the autoclave capable of forming the AuIII ion, and gold chloro-complexes result from the addition of small quantities (~5-10 g/L) of sodium chloride to the autoclave. The principles of the PLASTOL® process are briefly described, and several applications of the process to gold concentrates are presented. Various options available to recover gold from PLASTOL® leach solutions are also discussed.

Jan 1, 2003

By Sergio Demetrio

Based on the current reality of the copper smelters industry, besides the advances that have been and are expected for the next few years, the authors present a futurist vision of the processing of copper concentrates and copper smelters in the years 2000. Outlined new development strategies and ways of improvement in this business, including research, development and management of the works that today posses characteristics of a profitable operation, as well as the changes expected with respect to the entry of new actors and the creation of new products The authors finally bet for small or tailor-made smelters with ad hoc technology for their raw materials and few units to coordinate -devoted to specific concentrates using high technology and low manpower. Considering the in-situ hydrometallurgical route, as well as the pyrometallurgical route in works or conversion facilities that buy or process white metal and produce copper and other metals associated with this such as gold and silver, besides sulfuric acid, plants which should be strategically located in zones with high sulfuric acid price to make this a product which contributes to the profitability of the business.

Jan 1, 1999

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By P. A. Rusin

Many manganiferous silver deposits remain undeveloped because standard chemical extraction methods yield poor recoveries or are ' environmentally unacceptable. Biotreatment of such ore deposits in our laboratory resulted in manganese and silver recoveries of greater than 90%. Ore and sediment samples were collected from mining sites in Colorado and Arizona. Portions of samples were incubated in a semi-solid mineral salts medium amended with 20 mM glucose mid manganese dioxide (Mn medium). The cultures were incubated at 3(fC until manganese reduction was detected by a .color change fr:om .black to clear. Bacteria from these cultures were purified on Tryptic Soy Agar and individual isolates were retested for Mn reduction by an agar overlay method. Bacteria were identified according to Bergefs Manual ?of Systematic . Bacteriology. Most of the Mn-reducing bacteria are Bacillus species. Bacterial manganese reduction kinetic experiments were performed in 52 ml mineral salts broth supplemented with manganiferous silver ore instead of manganese dioiide. These cultures were incubated with agitation for 16 d. Aliquots were removed periodically and analyzed for solubilized manganese by atoniic absorption (AA). Cyanide (1,0 M) Vias added to the remaining ore-medium mixture for a 24 h bottle roll. The supernatant was analyzed for soluble silver by AA. Similar experiments were conducted on a larger scale using 15% pulp density. After bfotreatment of the ore, standard bottle rolls were performed. The pregnant solutions and the residues were analyzed for manganese and silver?using AA or fire assay as appropriate. In sterile. controls-which received no biotreatment, manganese and silver recoveries were 0.3% and 10% respectively; During biotreatment, total manganese solubilizatiori was as high as 99.8%. The reduced manganese could . be stripped from ?the growth medium using hydrometallurgical techniques. Silver recovery vaned from 70% to 92.5%. Microbial treatment of refractory mangairlferous ores can result in high recoveries of manganese and silver. Retention time varies depending upon the relative concentrations of manganese, silver, and other metals in the ore with only two days required in some cases, The biotreatment of ore is environmentally' acceptable while the use. of chemicals such as sulfur dioxide is less so.

Jan 1, 1991

By Varadajan Seshadri

Torpedo cars have been extensively used for pig iron desulfurization although its geometry is not considered to be ideal as far as mixing and mass transfer are concerned. Complications arise from scaffolds formed through aggregation of flux, slag and pig iron during operation. Following industry demand a 1:6 torpedo car physical model was operated to assess the optimum refining conditions for pig iron desulfurization. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation, presence of scaffold were evaluated. Mixing times were found to be shorter than regular desulfurization time and also not very sensitive to scaffold presence. Scaffold contributes to the reduction of the useful volume only. Mass transfer at the permanent reactor is more effective when the torpedo is operated at its full capacity. The experiments also highlight the dominance of the transitory reactor as compared with the permanent reactor.

Jan 1, 2006

By P. S. Arthur

The ISASMELT? process is a submerged lance smelting technology operating in smelters in Australia, the USA, Belgium, India, Germany, Malaysia and China. Further plants are under construction in Peru and Zambia. Following the invention of the Sirosmelt lance technology Mount Isa Mines recognised the commercial potential in the novel top blown bath smelting process and embarked on a development program that has lasted more than 25 years. After successful operation of pilot plants and demonstration plants producing copper and lead, Mount Isa Mines decided to license the technology to external companies. Since the purchase of Mount Isa Mines by Xstrata in 2003, Xstrata Technology has assumed responsibility for transferring the technology to ISASMELT? licensees. In the 15 years since the first commercial furnaces started operation plants have been constructed (or are under construction) with a combined annual smelting capacity of more than six million tonnes of concentrates or secondary raw materials. Process development continues on the commercial scale plants at Mount Isa and elsewhere. Many of the improvements implemented by plant operators have been passed on to, and adopted by, other licensees. Exchange of ideas and technical improvements occurs through ad hoc visits to fellow licensee sites and through regular licensee workshops arranged by Xstrata Technology. This paper updates the reader on the status of various ISASMELT? plants either operating or under construction. It highlights the important role that the technology provider?s operational experience plays in ensuring that new smelting plants ramp up quickly to nameplate capacity.

Jan 1, 2006

By Jose Carlos D'Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano

The production and consumption of Direct Reduced Iron (DRI) are continuously increasing, as a consequence of the impact of shale gas extraction technology on the Natural Gas (NG) market. Considering this context, DRI may improve the Blast Furnace (BF), Electric arc Furnace (EAF) and LD converter ’s productivities and consequently their competitiveness. In this work the results of a cooperative research conducted by PUC-Rio University and a Brazilian mining company are presented. Laboratory-scale simulation tests, using DR commercial pellets and typical industrial operational parameters of a benchmarked DR shaft furnace, were conducted and planned using statistical and factorial analysis. In the simulated experiments, the following three regions of the DR shaft furnace were considered: Reduction Zone (RZ), Transition Zone (TZ) and Cooling Zone (CZ). Three stages were considered in the research development: (i) the reactions and equations concerning pellet metallization and Carbon precipitation were analyzed; (ii) experiments focused on the de finition of the carburization kinetic equations occurring in the Transition and Cooling zones, and finally, (iii) aimed to develop the “METCARB” model, a computational program conceived to simulate mathe- matically the metallization and carbonization reactions along the height of the furnace. In conclusion, a comparison is made with industrial results in order to validate the resulting “METCARB” model.

Mar 1, 2018