Search Documents

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By R J. Merchant

The Hauraki goldfield is located east of Auckland in the North Island of New Zealand. It includes Great Barrier Island, the Coromandel Peninsula and the Coromandel and Kaimai Ranges as far south as the town of Te Aroha and south east to Te Puke. It has a total north-south extent of about 180 km and an area of 3000 km2. The goldfield is the most productive in New Zealand, and while production at present is negligible, the area has undergone continuous exploration over the last seven years.

Jan 1, 1984

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By Neil T. Davie, Thomas K. Blanchat, Thomas C. Togami, Joe R. Weatherby, Dale S. Preece, Robert A. Benham, James J. Calderone

"Geotechnical structures ,such as underground bunkers, tunnels, and building foundations aresubjected to stress fields produced by..the gravity load on the structure and/or any overlyingstrata. These stress fields may be.. reproduced on a scaled model of the structure byproportionally increasing the gravity field through the use of a centrifuge. This technology canthen be used to assess the vulnerability of various geotechnical structures to explosive loading.Applications of this technology include assessing the effectiveness of earth penetrating weapons,evaluating the vulnerability of various structures, counter-terrorism, and model validation. Thisdocument describes the development of expertise in scale model explosive testing ongeotechnical structures using Sandia’s large scale centrifuge facility. This study focused onburied structures such as hardened storage bunkers or tunnels. Data from this study was used toevaluate the predictive capabilities oft existing hydrocodes and structural dynamics codesdeveloped at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA)."

Jan 1, 1998

There are no large rivers in Western Australia capable of supplying water for processing magnetite ores. If sea water is used there are severe corrosion issues and the requirement to wash the concentrates with potable water. If groundwater is used there is a need to treat the water and sustainability is an issue for large projects because of potential drawdown of the aquifer.If sea water is desalinated the cost of the water is high because of the power requirement. At the same time the necessity to conserve water has lead to flow sheets where all of the tailings have to be filtered to minimise the water requirement.Managing the various water qualities and optimising water recovery and quality has resulted in optimising the water balance and issues meeting environmental obligations. Reverse flotation is a critical final step in reducing the silica level in the final concentrate and requires good quality water.

Jan 1, 2009

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By D C. McPhail, S L. Rogers, J Brugger

Using iron- and sulfur-oxidising bacteria to catalyse the breakdown of sulfides that host the gold is an important biological method for the pretreatment of refractory gold ores. Following this biological treatment a combination of chemical and physical methods are used for leaching (such as the cyanide process) and concentration (such as carbon-in-pulp or electrowinning) of gold. Although these methods are well accepted by industry, they harbour limitations in the processing of low-grade refractory ores, and regulatory agency/public acceptance of cyanide use. Thus, it is beneficial to industry to develop environmentally friendly, cost-efficient leaching and concentration techniques that are based on micro-organisms. This may soon be possible by adapting the results of recent regolith geoscience research, which has shown that micro- organisms are capable of driving a biogeochemical cycle of gold dispersion, transport and reconcentration in the supergene environment. The indigenous microbiota in biologically active soil microcosms from a number of Australian sites are capable of solubilising up to 80 wt per cent of the gold contained in these materials during 50 days of incubation. Studies using molecular microbial techniques have shown that a metallophilic bacterium, Ralstonia metallidurans, is present in biofilms on gold grains from a number of Australian sites. R metallidurans is capable of actively accumulating gold from solution, suggesting that the bacterium may contribute to the formation of secondary gold grains and nuggets. Identifying the biochemical and physiological pathways that lead to the dispersion and accumulation of gold in regolith, and quantifying the reaction kinetics of these processes may thus lead to the development of industrial bio-processing capacities for gold-containing ores.

Jan 1, 2007

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

By E. Stoetzer

In all known deep mixing processes the existing soil is mixed with self hardening slurry by mixing tools that rotate about a vertical axis (augers, mixing paddles). Wall panels are constructed using sets of multiple mixing tools combined into a single unit. These techniques have been developed on the principle of the rotary drilling technology. In contrast, the new Cutter Soil Mixing or CSM technique is derived from the cutter technology. The soil is loosened and broken down by cutter wheels, then mixed in-situ by the rotating cutter wheels with the self-hardening slurry - introduced into the ground between the two wheels - to form a soil-slurry mortar. The main area of application lies in the construction of cut-off and retaining walls.

Jan 1, 2006

By Nicol S. K, Swanson A. R

The poor flotation response of many coals has in the past been attributed to such factors as differences in rank, differences in degree of oxidation, differences in petrographic composition, or slime coatings. The present work shows that while all these factors undoubtedly influence flotation, the size distribution of the feed may override these. Evidence is presented which shows how this factor can lead to substantial losses of coarse coal (>250 µm)from a coal which would normally be considered amenable to flotation. Reasons for this loss of flotation response are suggested together with means of overcoming the problem.

Jan 1, 1978

By J Youngson

Gold placers can be difficult to locate in areas where tectonic activity and paleogeography have changed significantly since placer formation. Existing placer exploration models are useful in areas that have a relatively simple geological history, identifiable relationships with parent sources, or a history of placer mining. However, exploration becomes increasingly difficult in areas where tectonic activity and sedimentary recycling repeatedly redistribute the gold. Gold placers in the Waitaki River catchment, North Otago, New Zealand have no primary source within the catchment. During the Eocene placer gold was transported by a river ('Buster River') that flowed in a northeast direction from Central Otago toward a coastline at Maerewhenua, North Otago. This river and coastal system was inundated by marine transgression during the middle Tertiary. Since the Miocene its placer deposits have been uplifted and eroded and any links with parent sources have been severed. Changes in paleogeography resulted in local reconcentration and local dilution of placer gold in different areas in the Waitaki catchment. Thin veneers of old Waitaki River gravels (Kurow Gravels), containing gold recycled from the older placers, have been deposited unconformably on strath surfaces cut into Tertiary or older rocks. These gravels along with remnant Eocene fluvial and shallow marine strata provide potential placer exploration targets. Uplift and erosion of non-auriferous rocks in the Waitaki catchment to the west and north of the study area has resulted in considerable dilution of potential placer deposits downstream, especially in areas of gravel aggradation. We present a placer exploration model that is founded on answering fundamental questions pertaining to the paleogeography and geological history of the sediments associated with the placers.

Jan 1, 1999

By S Yuen, T Rana, S Khan

Many open pit mines require dewatering or need aquifer depressurisation systems to manage mine water inflow and/or mine floor stability. In many instances these mining operations impact on regional groundwater resources and therefore access to these resources by other users.As such potential exists for mine development to be hindered or even blocked by groundwater legislation that aims to prevent declining groundwater levels and demonstrate equitable use of a regional groundwater resource.There is a need to manage aquifer systems during and after the mining operations, and in some cases stresses on the aquifers and associated ecosystems may be elastic and can be managed with minimum impacts or reversed once the mine ceases to operate.This paper uses the Gippsland sedimentary basin, with a history of declining groundwater levels and mining and petroleum production, as a case study to pose the question: Should period of mining operation, aquiferÆs storage capacity and its ability to recharge be concurrently considered when granting groundwater abstraction and mining licenses for prospective mine development?It further examines that by utilising an aquiferÆs storage capacity and demonstrating an understanding of aquifer system hydrodynamics during and beyond the life of the mine (time), the approval process for groundwater abstraction and associated cost of statutory monitoring may be made less onerous.

Jan 1, 2009