Search Documents

By T. Schmidt, J. Merza

"This study considers two lead/zinc/silver orebodies which have historically had a problem with pyrite, pyrrhotite and sphalerite contamination in the lead circuit. The problem was previously addressed with high dosages of sodium cyanide as the primary depressant. However, large amounts of cyanide led to environmental problems in the effluent, especially during winter months. The objective was to reduce cyanide consumption while maintaining or improving overall lead grade and recovery via the reduction of the undesirable sulphides.Extensive laboratory and mill testing was necessary to determine the optimal operating parameters for continuous plant application. Evaluation of data received from this testing has shown that selective addition and optimization of the dosage of Unimax SD100 to specific areas of the flotation and grinding circuits has resulted in improved Pb grade and recovery. Parameters such as pH control, regrind operation, the cyanide/Unimax ratio and sulphide mineral content may also affect the performance of the depressant. Each factor is discussed and optimal operating conditions were determined based on the testing.Results are presented for two case studies. Both indicate that Unimax SD100 improves the lead grade/recovery curve by increasing iron and zinc rejection while reducing cyanide consumption and the resulting environmental concerns. 1. Hart"

Jan 1, 1992

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Campbell Brown GA

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some inillioils of tons of rich, copper-gold ore, averaging about 45% to 50% silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux.were required. Unlimited quantities of cheap, limestone, were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting operations started, with one' furnace in January, 1906, using as flux low-grade sulphide ore fro:m. the mine, containing very little silica. When the second, furnace was blown in this was supplemented by ironstone from, small aeposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Eabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required viz, 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1912

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

Rheological Behaviour of Clay-Rich Gangue Mineral Dispersions During Hydrometallurgical Treatment Alumino-silicate minerals invariable may present an intractable challenge in hydrometallurgical operations employed in low grade nickel, copper and gold ore leaching or high level nuclear waste (HLNW) processing. The interactions and reactivity of alumino-silicate clay gangue minerals such as muscovite/sericite, chlorite, kaolinite and smectite under acidic (eg pH <3) or alkaline (pH >13) conditions can have a striking impact on the particle interactions. These may manifest in undesirable pulp rheology, poor extraction rates and challenges in the subsequent "handleability" and solid-liquid separation processes (eg dewatering). In the present work, a review of investigations involving the interfacial chemistry, interactions and rheological behaviour of aqueous dispersions of mica-group, layered alumino-silicate clay (muscovite / sericite) and chalcocite minerals as a function of pH in the range 2 - 9 and time at 25¦C, is presented. Particle zeta potential, reflecting interfacial chemistry, indicated a strong pH-history and particle volume fraction dependency. Pristine particles' zeta potentials measured from high to low pH indicated mineral-specific isoelectric point (iep) at pH range 2 - 5. Subsequent measurements from low to high pH showed pH-history dependency with iep shift to higher pH values, the extent of which also depended upon particle volume fraction and aging time. Pulp pH-mediated particle interactions revealed by shear yield stress analysis displayed a bifurcation behaviour and good compliance with DLVO theory. The maximum pulp yield values occurred at the iep whilst weak rheology was observed where the magnitude of the particle zeta potential was greatest. The pivotal role played by both pulp chemistry and suspension conditions in regulating the particle interactions and concomitant rheological behaviour is highlighted. The implications of the findings with regards to clay-base pulps' handleability and its control during aqueous processing are discussed.  

Sep 13, 2010

By Grant Loveday, Vincent Dieudonné, Andrew Jonkers

Bateman Minerals & Metals supplies the APIC Technologies which include the under-bed air-pulsed APIC jig and related technologies such as the JigScan controller and advanced mathematical models of the jig process. Bateman have developed a methodology for predicting process performance for jigs from simplified testing and modelling, based on batch equipment matched to industrial designs. Batch tests conducted on laboratory scale air-pulsed jigs can process small batches of material, such as those obtained from drill core samples. The novelty comes from using an advanced jig process model, ASTRAD, to link the results of batch and continuous jigs. The batch jig presented as a novelty in this paper has been designed to be hydraulically equivalent to the full-scale APIC Jig, allowing the generation of equivalent pulse shapes and using JigScan controller. Lump and fine ferrous ore material have been separated in this unit and any feed >1mm can be tested and extracted. The global test procedure and further modelling focus on the stratification of material, with emphasis on key aspects such as pulse shape, feed characteristics and residence time. The splitting of rejects from concentrates is itself more difficult to reproduce in batch jigging, however the ASTRAD model includes a separation imperfection module, and the APIC Technologies have extraction systems adapted to each type of material. Air pulsed batch jigs are available in several locations and are relocatable. They have been used to treat samples from Australia, South Africa and India as part of studies into ore processing using jigs. Each test layer is available for various physical testing procedures (density and chemical analyses). Test-work is performed on a case by case basis, and analysed using an advanced model ?now available over the internet. Some fundamentals of air-pulsed jigging are recapped along with some of the features of APIC jigs. The process of designing a ?hydraulically equivalent? batch jig test is then described. Some results from jigging tests are presented plus the results of the ASTRAD advanced jig model, which was first developed at the JKMRC with ferrous ores and coal and is now being supported and further developed and utilised by Bateman.

Jan 1, 2006

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

By J. W. Jamieson, J. Escartin, A. Steinführer

Evidence of hydrothermal activity on two Mid-Atlantic Ridge oceanic core complexes (OCCs), at 13º30’N (the Semyenov 1 through 5 fields) and 13º20’N (the Irinovskoe field) (Fig. 1) were studied using CTD casts, dredges, TV-grabs and SP surveys during previous research cruises to these sites (Cherkashev et al., 2013, McLeod et al., 2009). In late 2013, the Semyenov and Irinovskoe fields were revisited, this time with an autonomous underwater vehicle (AUV) and a remotely-operated vehicle (ROV) during the ODEMAR (Oceanic Detachments at the Mid-Atlantic Ridge) cruise on the French research vessel "Pourqoui Pas ?". Here we present the first visual surveys and direct sampling of these vent sites. High-resolution (~2 m) bathymetry of the 13º30’N and 13º20’N OCCs and their associated vent fields was collected during 4 and 5 AUV dives, respectively, using the GEOMAR AUV "ABYSS" (Fig. 1). These surveys were flown between 70 m and 100 m above the seafloor, typically at a constant height to reduce vehicle movement. The AUV was equipped with Eh, turbidity, and temperature sensors in order to detect active hydrothermal venting. Over twenty ROV dives with the ROV "VICTOR 6000" allowed for the visual exploration of the OCCs and collection of 59 hydrothermal rock samples from the vent fields. As a result of these exploration activities, the first robust estimates of the size of the deposits, and the geologic controls on sulfide accumulation at these sites can be determined.

Sep 1, 2014

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By P. G. Gresse

The Orange-Vaal River system is known to be the primary secondary source for alluvial diamond deposits in the northern Cape and along the west coast of Namaqualand. The higher order sources for diamonds contained within this system are still not defined entirely to satisfaction, but certainly include kimberlite pipes exposed in the catchment regions of these rivers. The focus of alluvial diamond mining along the Orange-Vaal system recently changed from the traditional areas in the upper catchment regions?the Barkly West, Christiana, Bloemhof, Wolmaranstad, Schweizer-Reineke region, and the lower regions near the mouth of the Orange River at Baken, Alexander Bay and Oranjemund, to the area between Douglas and Prieska?the so-called mid-Orange region (Figure 1).

Jan 1, 2003

By Lamont G

The significance of blasthole stemming in determining blasting efficiency has been extensively studied for small diameter holes using gelignite explosives. Recent developments in blasting technology with the use of large diameter holes and low cost blasting agents have not included studies of the effectiveness of different types of stemming materials. A review of previous measurement techniques and the relevance of these earlier results to present stemming practice is presented in this paper. A survey of operating mines in Australia provided information for this analysis. The value of stemming in reducing blast noise and improving blasting efficiency is generally accepted but the use of bulk-loaded explosives in underground operations has resulted in the practice of eliminating the use of stemming material.In surface operations drill cuttings are used for stemming on the basis of availability rather than efficiency in providing resistance to movement. The development of laboratory testing techniques, based on noise level and borehole pressure measurements, to evaluate the relative efficiency of different types of stemming materials is described. The results of an extensive series of tests with ANFO explosive showed similar trends tothose obtained from earlier published results with gelignite type explosives. Conclusive quantitative results on the relative effectiveness of different stemming materials will require minor modifications to the existingequipment. Observations and the results of pressure measurements indicated the presence of shock wave effects which caused the ejection of the top section of the stemming column when using coarsely fragmented material.

Jan 1, 1979