Search Documents

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By P K. Smith, N G. Corner, R J. Ryan, D C. Arne, F P. Bierlein

The Reefton Goldfield has produced 67 t of gold from mesothermal vein gold deposits in metasedimentary rocks of the Greenland Group (Cambrian-Ordovician). The Globe-Progress deposit contributed 13.2 t (418,000 oz) of this total, predominantly from quartz veins. Recently a resource of 14 Mt at 1.96 g/t Au (27.5 t or 882,300 oz of contained gold) has been delineated at Globe-Progress in quartz vein remnants and disseminated within adjacent sedimentary rock, much of which has been locally brecciated. The breccias consist of quartz vein and sedimentary wall rock fragments set in a matrix of clay ærock flourÆ and sulphide (arsenopyrite plus minor pyrite and stibnite). Gold, closely associated with sulphide, is disseminated within the breccia. Disseminated gold also occurs in massive siltstone and sandstone adjacent to the quartz veins and breccias. Exploration drilling at Globe-Pogress, and several other Reefton prospects (e.g. Capleston, Merrijigs, Big River and Alexander River), has intersected zones of disseminated arsenopyrite carrying up to 20 g/t more gold. These mineralised sediments commonly have little or no megascopic quartz and or carbonate veining. There is little visible indication of former primary or secondary permeability for the passage of hydrothermal fluid and deposition of gold. However, porosity and permeability were formerly present in inter-granular pore spaces and microveinlets now filled with quartz, carbonate and K-mica. The Fosterville gold deposit in Victoria bears many similarities to the Globe-Progress deposit at Reefton, in terms of age, host rocks, hydrothermal alteration and mineralisation style. Many ofthe disseminated deposits in Nova Scotia, including deposits at North Brookfield and Moose River (Touquoy Zone), have similar characteristics to the Reefton disseminated mineralisation, but commonly have abundant pyrrhotite and some deposits have disseminated metal alloy grains of complex metallurgy.

Jan 1, 2000

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (') The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961

By G. Biles, K. Loughran, R. Anand

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralised zones, which are less economic or uneconomic as direct shipping ore. Test work demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and 150tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime’s shares and manages and operates the mine on Prime’s behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

An Ammonia Leaching-Solvent Extraction-Electrowinning-Flotation Process for Copper Oxidised Ore Treatment

Sep 13, 2010

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905