Search Documents

By Ren G. Dong, Jay Kim, Daniel E. Welcome, Won Joon Song, Charles Hayden

Prolonged, extensive exposure to hand-transmitted vibration could cause a series of vibration-induced disorders in the vascular, sensorineural, and musculoskeletal structures of the human hand-arm system, which have been collectively called hand-arm vibration syndrome (HAVS).1 To assess the risk of HAVS the international standard ISO 5349-1 (2001)1 recommends using the root-mean-square (rms) acceleration of the measured vibration with a frequency weighting. While a few epidemiological studies have reported results consistent with the predictions made according to the recommendation, many other studies have reported results with large discrepancies.2 This may be partially attributed to the time-averaging effect involved in calculation of the frequency components, especially for impact type tools. Because the spectral characteristics of impact tools change dramatically with time, a time-frequency (T-F) analysis can provide better characterizations of such highly transient vibrations. The analytic wavelet transform (AWT) is an ideal T-F analysis tool because it possesses the advantages of both the Fourier transform and the wavelet transform.3 The objective of this study was to explore the application of the AWT method for characterizing the impact tool vibrations and assessing their exposure risk. Methods Five tools (two chipping hammers, two riveting hammers, and one concrete cutting saw) were used in this study. The saw vibration was measured when it was used to cut a section of road pavement during a repair. The vibrations on the other tools were measured by the procedure specified in ISO 8662-2 (1992).4 A sampling rate of 16,386 Hz was used in the measurement. The AWT and Fourier analysis were applied to these signals and to identify their characteristics. Results Figure 1 compares the T-F characteristics of the accelerations measured from the relatively steady concrete saw and a riveting hammer. The frequency weighting specified in ISO 5349-11 was applied in the calculations. The comparison clearly shows that the two tools have completely different T-F characteristics.

Jan 6, 2006

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk. Keywords platinum, mining, community, socio-economic impact, stakeholders, conflict, labour unrest, social licence to operate, investment, Africa.

Mar 1, 2013

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

Removal of Arsenic in Fluorite Ore by Simultaneous Grinding-Leaching with NaHS Generally speaking, a high-grade fluorite ore is converted into hydrogen fluoride (HF), which is essential for the semiconductor manufacturing. With the continuous depletion of resources, novel technologies for processing low-grade fluorite ores are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, a low-grade fluorite ore was upgraded by removing arsenic, which is difficult to remove by conventional method. The mechano-chemical leaching of fluorite ore (i.e. the sample was ground in presence of NaHS, using a beads mill) was carried out to investigate the removal of arsenic from the low-grade fluorite. Experimental results showed that the arsenic concentration was reduced to 73.2 mg/kg.

Sep 13, 2010

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By M. van Schoor

The bulk of the world?s platinum production originates from the Merensky and UG2 reefs within the Bushveld Complex, South Africa. Both the Merensky and UG2 reefs are disrupted by faults, dykes, potholes and iron-rich ultramafic pegmatite bodies (IRUPs)?features that impact negatively on production, planning and safety. It is therefore advantageous to know of their presence and geometry ahead of mining. To date, no geophysical technique has been successfully applied to the routine mapping of mine-scale potholes and IRUPs. These disruptive features may vary from a few metres to several tens of metres in diameter. In this paper the applicability of in-mine electrical resistance tomography (ERT) to map potholes and other disruptions to the continuity of the Merensky and UG2 reefs ahead of mining is demonstrated using two case studies.

Jan 1, 2005

A model was developed of a CIL/CIP circuit for recovery of gold and silver. The model uses a simple two rate representation of the leaching kinetics. Parameters for the leaching kinetics may be simply obtained by sampling the feed to a circuit and the tailings from each tank and assaying the solids for both gold and silver to obtain the assay profiles of the solids down the tanks. The parameters in such a leaching model would be expected to be a function of the ore type, the grind, whether oxygen was used and the general chemical environment. These parameters are primary inputs to the model for any simulation. Standard power law relationships are used to express the practical equilibrium between the gold and silver cyanides adsorbed on the active carbon and the tenor of the solutions. The parameters for this may be derived from solution and carbon assays for the same set of samples. The model is constructed by writing a mass balance for gold and silver in and out of each tank in the train and for the circuit overall. Other inputs to a simulation are the feed rate of ore, per cent solids of the slurry in the tanks, gold and silver loadings of the input æbarrenÆ carbon and the rate of movement of carbon through the circuit counter-current to the slurry. With appropriate practical parameters the simulation is able to reproduce typical tank profiles.

Jan 1, 2004

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li20-A1203-4Si02), a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Hills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade deposits in forth Carolina. The theoretical lithia (Li20) content of spodumene is 9.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of 'standard' hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

Low displacement fault zones often comprise a mesh of interlinked faults, extensional-shear and purely extensional vein fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major through going faults. Mesh formation generally involves hydrofracturing (Pf > s3, at least locally) and the condition Pf ~ s3 to be maintained for the mesh to remain a high permeability conduit, requiring fluid over pressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc. Fluid redistribution in the crust is influenced by maximum hydraulic gradient (not necessarily vertical), by existing permeability anisotropy arising from bedding and other forms of crustal layering, and by structural permeability developed under the prevailing stress field. Strong directional permeability develops in the s2 direction, parallel to fault-fracture intersections within the mesh and orthogonal to fault slip vectors. In particular tectonic settings, stress-controlled permeability allows strongly focused flow through fault-fracture meshes with high potential for mineralisation. Favoured localities for mesh development include short-lived link structures along large-displacement fault zones such as dilational jogs, lateral ramps, and transfer faults.

Jan 1, 1995

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

The pellet plant, built by Dravo Corp, in Groveland, Mich., for the Hanna Mining Co., is now in full operation. Although using jasper, a type of iron ore with low iron content (approximately 28% Fe), the plant has a rated capacity of 1,250,000 tans of pellets per year. In its four years of existence, the nearby concentrating plant has seen its capacity increase from 700,000 tons to 1,500,000 tons a year as part of a major expansion program at Groveland. Utilizing the Dravo-Lurgi continuous grate process, the pellet plant produces %a-in. pellets of more than 60% iron content. The fully-hooded pelletizing grate, largest in the U.S., is 9 ft. 10% in. wide and 223 ft. 1% in. tong over 34 windboxes, with an effective hearth area of 2195 sq. ft. Drying, firing, and cooling functions are all carried out on this single piece of equipment.

Jan 4, 1964

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.