Search Documents

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By P. J. Williams, A. R. Foster

Petrographic studies, assay records, and laser ablation-inductively coupled plasma-mass spectrometer (LA-ICP-MS) analyses of major sulfides suggest nearly all of the gold at the Ernest Henry Cu-Au deposit occurs in the form of native gold or electrum (95-65 wt.% Au); sylvanite and dissolved gold in cobaltite, chalcopyrite, and pyrite make only minor contributions. LA-ICP-MS analyses of the gold contents of chalcopyrite gave from 8 to 139 ppb (mean = 56 ppb), more than an order of magnitude lower than those experimentally determined in chalcopyrite in equilibrium with native gold at the estimated mineralization temperatures (350°-450°C). Gold content is more variable in pyrite (1-400 ppb, mean = 77 ppb) and highest in narrow growth zones of a subordinate type of complexly zoned pyrite wherein it is associated with elevated As, Ag, Sn, Sb, Te, and Bi. Deposition of gold-electrum was closely associated with, but preceded some of the chalcopyrite deposition, as indicated by microtextures and lower bulk Au:Cu ratios in late-stage chalcopyrite-rich veins. Gold grains have maximum dimensions from <1 to 50 micrometers, and are heterogeneously distributed with most occurring in microscale clusters. Fifty-five out of 76 grains recorded in polished sections are in contact with both chalcopyrite and pyrite, and many of the rest are in sites where such a relationship could exist in the third dimension. The dominant textural sites are intergrowths with chalcopyrite in microveinlets cutting pyrite, and on faces of pyrite grains in contact with chalcopyrite. Scanning electron microscopy, electron microprobe analysis, and proton induced X-ray emission studies show that pyrite associated with gold includes complexly zoned, weakly zoned, arsenian, and arsenic-poor types. The textures are compatible with the possibility that most gold was deposited electrochemically as native metal on pyrite surfaces. The textural distribution of gold has important metallurgical implications given that the ore processing circuits at Ernest Henry and most other sulfide copper mines are designed to exclude pyrite (and arsenic) from concentrates.

Jan 1, 2007

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By J. M. Richards

For most of the 20th century optical petrography has been the primary petrological and mineralogical tool used to characterize coal. The development of quantitative SEM-based techniques, e.g. QEMSCAN®, for coal began only about a decade ago. The application of these techniques for coal lagged behind other commodities, but they are currently being developed with the aim to provide ?one complete analysis? for coal. Quantitative SEM-based techniques are supplemented by quantitative X-ray diffraction (XRD). Recent indications are that these more modern techniques cannot replace the ?standard? petrographic and chemical evaluations, but rather complement them where and when required. The great advantage of quantitative SEM-based techniques is that they are very rapid, with the result that large volumes of samples can be processed on a routine basis. This is ideal for coal type identification, since the results can be used in the creation of ?intelligent? composites. This can lead to the more speedy evaluation of coal deposits by reducing the number of samples on which detailed metallurgical and characterization test work is required, without an increase in the overall statistical error of the resource model. Coal petrography, however, remains important for the prediction of the coking characteristics of certain coals and coal products. As a consequence it is therefore important that any coal laboratory be able to produce data with confidence. This requires strict quality control and assurance protocols that adhere to international standards. Keywords coal petrography, coking strength, scanning electron microscopy, QEMSCAN®.

Nov 1, 2013

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well&#183;known and justly notorious anticlinal, or, as they are more commonly known, &quot; saddle&quot; reefs of Bendigo, comparatively little noticehas been given to the synclinal or &quot;inverted saddle &quot;reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

Generating short- and long-term mine production schedules in isolation and independently from each other means that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and long-term activities simultaneously. This paper addresses the task of integrating short- and long-term production plans by combining the short-term objective of minimising deviation to targeted mill feed grade with the long-term objective of maximising net present value (NPV) into a single mathematical model. A case study is presented which compares the present values of the same stope data set scheduled via separate long and short-term models and than by the proposed integrated model which applies a predetermined penalty for each tonne of metal deviation to target for the respective ore tonnage being processed. This allows an operation to obtain a globally optimal scheduling regime when taking into consideration the cost and loss of value resulting from fluctuations in grade to the mill over the short-term.

Dec 6, 2010

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about I part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for &quot;Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.,&quot; as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no. 1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc.

Jan 1, 2009

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions. &nbsp;

Jan 1, 1995

By A. T. Robles, L. Buckingham

"When certain gold ores containing pyrite, graphite, humates and fumates or other organic compounds which are possibly adsorbed on clay minerals are treated with aqueous solution of alkali metal cyanide, the aurocyanide complex which forms is adsorbed by these ""pregrobbing"" species in the ore. Dissolution of gold proceeds until chemical equilibrium is attained between the cyanide complex adsorbed by the ore and in solution.Sodium lauryl sulfate (SLS) may be used to decrease the adsorptive activity of the prerobbing species in the ore. It has successfully improved recovery at Holt-McDermott Mine and is highly biodegradable.INTRODUCTION Precious metal-bearing ores containing preg-robbing species are poorly amenable to standard cyanidation techniques. The ""preg-robbing"" impurities with which they are associated tend to adsorb the gold cyanide complexes and carry them through the circuit to the tailings. Also, gold may be associated with these impurities in the ore and not be leached by the cyanide complexing agents used in conventional cyanidation techniques.Methods for dealing with the problem of preg-robbinq impurities in gold ores are:Carbon-in-Leach (CIL), in which granular activated carbon is added to compete with preg-robbing species for the gold cyanide complexes. This process can improve gold recovery in mildly preg-robbing ores especially when fine carbons with very high activities are used. However, with severely graphitic ore, the carbon associated with the rock may outperform the granular activated charcoal.Chemical Oxidation, in which the ore is subjected to preliminary chemical oxidation techniques to oxidize carbonaceous materials using such diverse reagents including ozone, sodium hypochlorite, calcium hypochlorite, chlorine gas, permanganates, perchlorates, chlorates and oxygen prior to subjecting the oxidized ore to standard cyanidation treatment to extract gold. This is generally a costly method and will not prove economical on a low-grade ore."

Jan 1, 1992

By F. J. Brenner

The Slippery Rock Watershed Coalition was organized to restore a 70 km2 portion of the headwaters of the Slippery Rock Watershed in northwest Pennsylvania. Thirteen passive treatment systems have been installed with engineering and funding provided by private industries, county government and the Commonwealth of Pennsylvania. In addition, experimental systems have been installed at the Jennings Environmental Education Center which, in addition to monitoring the systems installed within the watershed, provide an array of educational and research opportunities for secondary, college and university students. The coalition sponsors an annual seminar for students to present the results of their research and field trips for public officials and private citizens to learn how public and private partnerships work together to restore the Slippery Rock Creek watershed.

Jan 1, 2002

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992