Search Documents

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)'s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

The use of mining by-products for beneficial use may face approval, and acceptance barriers. This paper described the use of a sustainability framework to assess the safety, effectiveness and economic value of modified bauxite residue (Alkaloam«) for use on agricultural land in the Peel-Harvey region of Western Australia. The results indicate the merit associated with using this by-product from a safety and, private, community and environmental value perspective. They may be used to indicate the worth of pursuing any future community acceptance and agency approval process.   The use of Alkaloam« for beneficial use on agricultural land in Western Australia was first investigated over 25 years ago. Efforts to gain regulatory approval and community acceptance of Alkaloam« have had a complicated and enduring history. Understanding and assessing the value of a by-product using social and economic considerations, in conjunction with an environmental assessment, provided a more complete evaluation to that previously used.

Jun 1, 2010

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By Keith Pucalik

Understanding Vibrations fr om Blasting focuses on explaining blast vibrations and their effects on people and homes while keeping an eye on the importance of the use and significance of explosives in our daily lives. Unlike many predecessors, this film will help blasting pro f e s s i o nals explain blast vibrations and address many of the layman’s most fre q u e n t l y asked questions. The film can be used in pubic hearings, given to homeowners during preblast surveys, or played at educational seminars for professionals. The film can also be used after blasting has begun and residents have already experienced vibration events.

Jan 1, 2004

Temperature Sensitive Polymers as Efficient and Selective Flotation Collectors

Sep 13, 2010

By J. Pinkley

DSI DYWI Rock Dust application is aiding in enhancing safety and productivity in underground coal mining. DSI DYWI Rock Dust combines wet dusting technology and polymers to allow for drying and lift characteristics for rock dusting. DSI DYWI Rock Dust typically dries within 24 to 48 hours depending upon the mine air velocity and humidity. The DSI DYWI Rock Dust Applicator Machine is a completely hydraulic unit. The DSI DYWI Rock Dust Applicator machine allows for batching of product and face spraying operations in permissible locations. The DSI DYWI Rock Dusting Applicator Machine fits in one half of a battery or diesel scoop bucket for ease of transport. It is completely hydraulically powered by the PTO circuit. The DSI DYWI Rock Dust Applicator unit requires a scoop operator, and a person to operate the spray wand, simple operation with two personnel. The first demonstration was at an underground continuous miner room and pillar coal mine which produced a pilot test period opportunity, which proved to be successful, and has now been in full launch mode with the US underground coal mining industry. A typical batch of operation allows for 250? of roof and rib (19? wide by 6? in height) coverage of DSI DYWI Rock Dust application. The DSI DYWI Rock Dust Applicator contains a hydraulic powered air compressor which allows for 30-50% more coverage per batch by improved dispersion of product via air assist spray nozzle. DSI DYWI Rock Dust will add approximately $0.02 to $0.04 per clean ton of coal cost to the mining operation over traditional rock dust cost depending upon mining height.

Jan 1, 2012

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By L. W. Bahney

MANY methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,1 or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,7 cement copper.8 4. Precipitating the silver by zinc dust held in a Hooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.10 6. Colorimetry.11

Jan 2, 1915

By Roberto Chambi

El presente texto describe las experiencias relacionadas al desarrollo e implantación del Sistema deTopografía para la mina subterránea de produccción polimetálica Raura. Para ello, se desarrolla la importancia de la topografía en el diseño y los proyectos mineros a través de un sistema de cálculo y dibujo topográfico. Los principales objetivos del sistema son: la gestión de la base de datos topográficos de la mina, la sustitución de las operaciones matemáticas “manuales” y la eliminación de sus errores inherentes, así como realizar automáticamente los dibujos de labores mineras a partir de la data recolectada y procesada, tanto en cálculos como en dibujo. De forma que se genera información procesada a los software especializados en geología y planificación.

May 25, 1998

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By Robert Hopler

Earthquakes, ground vibrations, seisms, or whatever you want to call the shaking of the earth, have been a fact of life throughout time. In spite of this, most people (except those unfortunate enough to live in seismicallyactive areas) have probably never felt this phenomenon, or if they have, only a very few times in their entire lifetime. However, when it does happen, nothing is more frightening than the sudden shaking of the earth beneath us - after all, we think of the ground we walk on as the unyielding, solid underpinning of our existence.

Jan 1, 2006

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By Ren G. Dong, John Z. Wu, Daniel E. Welcome, Kristine Krajnak

Although the exact mechanisms underlying vibration white finger (VWF) are not clear, it has been speculated that VWF is associated with variations of the blood flow patterns due to the physical damage and/or degeneration in neural and vascular tissue caused by vibration loading [1]. Excessive dynamic deformation of the soft tissues in the fingertip under vibration loading is believed to induce multiple occupation-related hand/finger disorders. However, the in vivo distributions of the dynamic stress/strain of the tissues in the fingertip under vibration conditions have not been studied because they cannot be measured experimentally to date. The goal of this study is to analyze, theoretically, the location and frequency-dependent dynamic deformation of the soft tissue in the fingertip during vibration exposures. [ ] Methods The fingertip considered in the model is the distal phalanx, the portion from the distal end of the fingertip to the distal interphalangeal (DIP) joint articulation (Fig. 1). The external shape of the fingertip was determined using a smooth mathematical surface fitting to the observed fingertip shapes. The fingertip surface was then scaled to the dimensions of a typical male index finger: length 25 mm, width 20 mm, and height 18 mm. The fingertip was approximated to be symmetric, such that only a half of the fingertip was considered in the FE modeling. The fingertip was assumed to be composed of outer and inner skin layers, subcutaneous tissue, bone, and nail. The soft tissues (inner skin layer and subcutaneous tissues) were assumed to be nonlinearly elastic and viscoelastic, while the bone, nail, and outer skin layer were considered as linearly elastic. The simulations were conducted using a displacement-controlled protocol in two stages. First, the fingertip was statically pre-compressed. The contact plate was first displaced towards the finger to achieve a predetermined value of tissue deformation (i.e., 0.5, 1.0, 1.5, and 2.0 mm). Second, the steady-state dynamics responses of the fingertip were analyzed using a linear perturbation procedure. The fingertip was subjected to a continuous harmonic excitation (magnitude 0.5 mm) from the contact interface. The dynamic analysis was performed in a frequency domain ranging from 16 to 2000 Hz. The frequency-dependent distributions of the vibration magnitude and dynamic strain magnitudes in the soft tissues are investigated. Results Typical simulation results for the frequency-dependent distributions of the vibration magnitude in the soft tissues are shown in Fig. 2 (figures show the results with a pre-compression of 2.0 mm). The vibration magnitude at the contact surface is 0.5 mm (specified) for all frequencies, while the vibration magnitudes in the soft tissues are location- and frequency-dependent. It is clear that the fingertip has a major resonance around 125 Hz, at which the vibration magnitudes in the soft tissues are over four times greater than that of the contact plate (0.5 mm). It is interesting to observe that, at this resonant frequency (125 Hz), the soft tissues at the tip has the maximal vibration magnitude while the regions near the contact

Jan 6, 2006

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993