Search Documents

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

By Anthony D. Barley

Over 60,000 multiple anchors have been used internationally since their introduction in the early 1990s, including 1000 in the United States. The multiple anchor system comprises a "multiple" of "unit" anchors installed within a single borehole - each unit anchor being staggered within the borehole length to mobilize its own capacity independently of the other unit anchors. These systems offer higher capacity than conventional anchors with identical bond lengths due to superior load transfer efficiency. The use of higher capacity anchors may allow reduction in the number of anchors required on a project, which results in time and cost benefits to the anchor installer, contractor, and the owner. Fully removable temporary multiple anchors are available, and have been used with consistent success. Three case histories are discussed highlighting the use of these systems

Jan 1, 2002

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By Gualberto Salas Torrelly

El avance tecnológico en los sistemas de iniciación en voladura abarca desde el sistema convencional (Mecha de Seguridad y Fulminantes hasta el sistema de iniciación electrónica, donde a través de un control de vibraciones se controla la energía liberada en un disparo, optimizando la fragmentación y disminuyendo el daño a las paredes del pit. En ese sentido, el sistema de iniciación con detonadores electrónicos, fija con claridad los conceptos de precisión, flexibilidad y seguridad. Por ello, el presente trabajo señala el uso de detonadores electrónicos por la Sociedad Minera Cerro Verde con la finalidad de evaluar sus resultados en seguridad, precisión, fragmentación, vibraciones, y control de daño a las paredes de la mina. Los resultados fueron óptimos -en tanto mejoró la fragmentación, el proceso de carguío y se incrementó el flujo en chancado primario.

Sep 12, 2005

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By G. Chi, A. Solomon, J. Lai

"The Buffalo gold deposit is a small deposit consisting of auriferous quartz-tourmaline veins within a granodiorite stock in the Red Lake greenstone belt. This study aims to characterize the mineralizing fluids through fluid inclusion and stable isotope analyses and to compare them with those of the world-class Campbell- Red Lake deposit. Four types of fluid inclusions were recognized, including carbonic, aqueous-carbonic, aqueous, and halite-bearing aqueous, with the carbonic type being the most abundant. Raman analyses indicate that the carbonic phase mainly consists of CO2, with minor amounts of N2 and CH4, and rarely detectable H2S. The homogenization temperatures of the carbonic inclusions range from -41.7° to 30.9°C. The homogenization temperatures and salinities of the aqueous, halite-bearing aqueous, and aqueous-carbonic inclusions are 130° to 276°C and 9.7 to 23.6 wt.% NaCl equiv., 155° to 207°C and 32.9 to 42.3 wt.% NaCl equiv., and 215° to 357°C and 8.3 to 19.7 wt.% NaCl equiv., respectively. The d18OVSMOW values of tourmaline range from 8.2‰ to 9.0‰, and those of quartz from 11.4‰ to 11.9‰, with estimated fluid temperatures from 323° to 399°C based on the quartz-tourmaline isotopic geothermometer. It is postulated that separate CO2-dominated and aqueous fluids intermittently invaded the fracture/vein system in response to fluid pressure fluctuations, with limited mixing. The CO2-dominated fluid, previously recognized in Campbell-Red Lake as the main mineralizing fluid, is inferred to have been derived from deeper parts of the crust. This deep CO2-dominated fluid reservoir might have been a common source for gold mineralization in the Red Lake greenstone belt. Le gîte aurifère Buffalo est un petit dépôt composée de veines de quartz-tourmaline à l’intérieur d’un stock de granodiorite dans la ceinture de roches vertes de Red Lake. Cette étude vise à caractériser les fluides impliqués dans la minéralisation par les inclusions fluides et par les isotopes stables ainsi que de les comparer avec ceux du gîte de classe mondiale de Campbell-Red Lake. Quatre types d’inclusions ont été notes, incluant des inclusions carboniques, aqueuses-carboniques, aqueuses et aqueuses avec halite, les inclusions carboniques étant la variété la plus abondante. Les analyses par spectroscopie Raman indiquent que la phase carbonique consiste principalement en CO2, avec des quantités mineures de N2 et de CH4, et rarement avec des quantités mesurables de H2S. Les températures d’homogénéisation des inclusions carboniques vont de -41.7° to 30.9°C. Les températures d’homogénéisation et les salinités des inclusions aqueuses, aqueuses avec halite et aqueuses-carboniques sont varient de 130° à 276°C et de 9.7 à 23.6 poids.% NaCl équiv., 155° à 207°C et 32.9 à 42.3 poids.% NaCl équiv., et de 215° à 357°C et 8.3 à 19.7 poids.% NaCl équiv., respectivement. Les valeurs de d18OVSMOW pour la tourmaline vont de 8.2 à 9.0‰, et celles du quartz de 11.4 à 11.9‰, avec une température estimée du fluide entre 323° et 399°C sur la base du géothermomètre isotopique quartz-tourmaline. Il est postulé qu’un fluide riche en CO2 et un fluide aqueux distinct ont envahi le système de fractures/veines par intermittence en réponse à des variations dans la pression des fluides, et qu’il y a eu peu de mélange. Le fluide riche en CO2 est également observé à Campbell-Red Lake ou il est le fluide minéralisant principal, il est présumé être dérivé de portions plus profondes de la croûte. Ce réservoir profond de fluides riches en CO2 pourrait être la source commune des minéralisations aurifères de la ceinture de roches vertes de Red Lake."

Jan 1, 2009

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958

By A. W. Bester

Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Eng.) Cullinan Diamond Mine currently handles 3.2 million tons of run of ore per annum. This is done by means of an underground train system, which is located at 763 metre level. Four trains, one in each quarter of the pipe, collect ore from passes and transport it to centrally located tips in the north and south of the pipe. The ore is then split into coarse and fine fractions. The coarse fraction proceeds to the primary crushers in the north and south. Historically, mining has been performed in such a manner that an equal amount of ore has reported to each quarter of the pipe. However, the tonnage profile of the mine will change such that the ore will no longer be split equally. For approximately five years the majority of ore will report to the east and thereafter most of the ore will report to the western portion of the mine. This will continue for the remainder of the current infrastructure level?s operational life. Coupled with this is the fact that the mine is aiming to increase its annual production to 3.8 million tons. The result is that the current ground handling system cannot accommodate the additional tons and therefore alternative ground handling options have been investigated. The continued existence of Cullinan Diamond Mine relies on finding a system that can economically handle the additional tonnage. Three options were investigated. Firstly, a train option, which would be an upgrade of the current system, was investigated. Two truck options were also investigated, the first of which was a conventional truck option. The second truck option was more interesting and involved an unfamiliar Combi truck system. The truck options were investigated primarily due to the fact that the block height of the BA West (a new production block) can be increased by 15 meters if a truck option is decided upon. This would create a significant increase in revenue for the BA West project. Each of the options was assessed in terms of its physical and financial feasibility. In terms of the physical constraints, it was found that all three systems could work. Detailed financial analysis indicated that either of the two truck options would be a suitable solution. However, due to the limited information regarding the Combi truck option, it should be further investigated. This applies particularly to the actual running and maintenance costs for the equipment.

Jan 1, 2005

By Frederic P. Dewey

The Bureau of the Mint of the United States Treasury maintains 13 ofEces for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, nine tables of comparative results, taken from the regular work of the service, are given..These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement in the assay-results, and follow through decreasing gold fineness and increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the agreement of the assay-results ; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these ire added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion,2

Jan 1, 1910