Search Documents

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By Dave Marsh, John Goode, Niels Verbaan, Kevin Bradley, Henrie Notzl

The mineralogy of the Avalon Nechalacho deposit is complex with significant fractions of HREEs, Zr, and Nb found in refractory minerals such as zircon and fergusonite. Sulphuric acid baking followed by water leaching can be used to extract REEs from flotation concentrates, but acid baking does not completely "crack" the zircon and fergusonite, so the extractions of Zr, Nb, and HREEs are not high. An alternative flowsheet has been developed that is able to obtain significantly improved extractions of HREEs, Zr, and Nb from flotation concentrates or acid bake residues. This is accomplished by cracking the zircon and fergusonite minerals with caustic soda at high temperatures, followed by water washing to recover excess caustic soda and soluble sodium silicates and phosphates. REEs, Zr, and Nb in the solid residue can then be solubilized with HCl or H2SO4. This paper highlights some of the findings from an extensive laboratory program and discusses several flowsheet implications.

Jan 1, 2014

Greymouth River Dredge û Birchfield Minerals Ltd Blackwater Gold Mine û Macraes Mining Company Ltd Globe Progress Gold Mine û Macraes Mining Company Ltd

Jan 1, 1996

By Tanner A. C, Harraway D. H

Various circuits were tried at Mount Isa Mines during the period 1959 to 19G3 with the objective of improving the differential flotation of galena and sphalerite. Many benefits and disadvantages of the various circuits were revealed. An analysis' of ore characteristics and their effect on flotation was made -and resullted in the design of a proposed circuit which is currently in the process of installation.INTRODUCTIONSince 1936 when lead-zinc sulphide flotation commenced at Mount Isa, at least three types of ore have been encountered.Each ore has presented problems to flotation metallurgists.The three types of ore are,1. partially oxidized upper level sulphide ore,2. Black Star ore from the lower levels with its carbonaceous fraction, and3. Black Rock ore which is similar to 2, but more free milling.In retrospect a number of the metallurgical successes of the past were short lived. Often flowsheets or 0perating practices were designed to solve a single metallurgical problem associated with the current ore being treated. As the ore changed the problem would vanish and the method originally taken to counter the problem could become unnecessary or deleterious to the treatment of the new ore. The general lesson learnt from-the past-is-that thetreatment of Mount Isa lead-zinc ore involves a number of equally major problems...

Jan 1, 1963

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By Garth Howlett

In 1998 the Matanuska-Susitna Borough formed the new port district at Point MacKenzie, known as Port MacKenzie, located directly across the Knik Arm from Anchorage. In 1991 PND Engineers Inc. (PND), working with the Matanuska-Susitna Borough manager and port director, envisioned a fill structure at Port MacKenzie with a 500-foot-long Open Cell? sheet-pile bulkhead face extending to EL -20 feet Mean Lower Low Water (MLLW) at the face. Now under operation the fill created 5.5 acres of tideland property using local materials for fill. The fill is protected from 2- to-3 foot-thick ice pans and 9 feet per second (fps) tidal currents by an envelope of armor rock. Construction required working in water with 30 to 40 feet of tidal variation. Construction required placement of frozen fill in water depths possibly exceeding 50 feet, creating real concerns about soil consolidation and long-term maintenance issues. A plan was prepared to consolidate the soils using Vibracompaction. Soil Density and consolidation were monitored during the work. In 2003 the port district and NPI, a wood chip export company, formalized an agreement to construct a deep water port facility at Port MacKenzie for cape-class bulk carriers. PND provided planning, studies, geotechnical investigation, design documents and construction inspection for a 500-foot-long trestle with a platform dockhead and dolphins providing 1,100 feet of dock face in EL -70 MLLW as shown in Figure 1. Design included installation of large-diameter spin-fin piles driven on a 2V:1H batter. Also included was a 300-ton tension test of smaller spin-fin piles.

Jan 1, 2006

Development of Process for Beneficiation of Low-Grade Iron Ore Samples from Orissa, India The paper deals with the results of characterisation and beneficiations studies undertaken on two low-grade Indian iron ore samples (IO-1 and IO-2) with a view to develop process for beneficiation of composite of the two samples to a high-grade concentrate, suitable for iron making through pelletisation. Indian iron ores contain relatively high iron but cost effective reduction of alumina within the specified limits has been a challenging task. Characterisation of the samples revealed the ore to be laminated and fine grained with hematite as the major mineral. Clay is the dominating gangue in most of the ore pieces followed by silica. Occasionally goethite and quartz/jasper were recorded. Clay occurs either as patches within the hematite mass or as cavity/fracture fillings. Liberation studies on the representative samples crushed to 2 mm indicated that around 95 per cent of the grains are liberated below 105 micron. Beneficiation of the two individual samples and their composite based on gravity and magnetic separation techniques resulted in products with varying yield and grade of the products. The effects of various process parameters were studied. Granulometry of the feed was observed to be important for improving quality of concentrate. The results of bench-scale studies were validated through pilot-scale continuous trials. Based on the studies undertaken a suitable process was developed for beneficiation of the composite sample, comprising 60 per cent IO-1 and 40 per cent IO-2, to a high-grade product assaying over 65 per cent Fe and material balance was computed. A commercial plant for beneficiation of low-grade iron ore to produce DRI pellet grade concentrate is proposed to be installed.

Sep 13, 2010

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

The notes from which this paper has been prepared were set down at the time of the author's departure from Australia in 1935. Mr. Frank Forman, Government Geologist of Western Australia, who has very kindly read the paper in manuscript, affirms that the views here set forth are now accepted by most geologists. Thus, Forman's recent presidential address before the Royal Society of Western Australia (1937) mentions sediments in the Kalgoorlie Series "including banded jaspers and jaspilites."While it may, therefore, be superfluous to belabour the question further at this time, Mr. Forman has encouraged the author to publish this paper as a summary or both past and present views.To those specially interested in the subject of the paper, a study of pertinent Plates attached to Western Australian Geological Survey Bulletin No. 71, 1917, is suggested.The type of rock which is variously called "jasper bar," jaspilite, or "ferruginous quartzite" is familiar to all mining men who have worked in the West Australian goldfields.In its typical form it is a "striped" rock consisting of alternate layers of white or pinkish silica with red to brown bands of iron-bearing silica.In the course of geological work in many parts of Western Australia I studied exposures of jasper bar and was repeatedly impressed with the similarity of much of the material to the sedimentary "banded iron formation" of Canada. It was, therefore, a surprise to learn that the jasper bars were not generally regarded in Australia as sedimentary horizons. It is true that Honman offered convincing evidence of the sedimentary origin of the jaspers...

Jan 1, 1939

By Pooley F. D

The coal measures of the South Wales coalfield contain at least 50 horizons at which coal seams are known, to occur. More than 300 samples of coal were collected from these coal measures and this paper outlines thefindings of an investigation of the pattern and distribution of 12 trace elements in South Wales coals. A comparison of trace element contents of the South Wales coals is made with trace element values found elsewhereand an attempt was made to establish the organic affinity of the elements in different seams and in the coalfield 'as a whole. An important function of such an analysis is to determine the order of abundance of trace elements and this was performed for individual seams and for the whole coalfield.The interrelationship of certain elements in some seams is also examined with a view to understanding the effectiveness of such an approach to seam correlation.Ranges of values are quoted together with the mean values of the various elements. Variations of elemental values within a seam section and over the coalfield as a whole are discussed.

Jan 1, 1977

By C J. Kruger, E le Roux

Anglo American Platinum has adopted a strategy of Best Practice Principles (BPP) for sampling, mass measurement, analysis and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned.The design called for the high-grade material to be crushed to 95 per cent passing 2 mm and the design allowed for a single cutter primary Vezin sampler, increments taken from a gravity flowing stream at regular intervals, whilst filling a tanker for the pneumatic offload at our base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from our smelting complex and the input to our refineries. In addition, the design incorporated the functionality to collect increments in an ‘interleaved’ fashion from the Vezin sampler for internal precision checks.The metal accounting strategy for Anglo Platinum is the ongoing measurement of all inputs, outputs and stock levels for all our operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February every year, across the smelters and refineries (at least the base metal refinery). A trend was developing in the accounting period immediately following the introduction of the new crushing and sampling facility, whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter (sender) showed an increase in physical stock compared to the theoretical stock and the base metal refinery (receiver) showed that their theoretical stock increased against their physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question and it was confirmed through the physical stock measurement results, that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream.This paper showcases parts of the process that took place to explain the poor accountabilities for the respective sites. Previous results from the sampler ratification process (of the interleaved sampling design) were analysed again, a physical inspection was carried out on the sampling system again and the sampler performance was monitored (quality control parameters) for the period.From these investigations, it was found that airflows present inside the Vezin introduced the sampling bias and a change in sampling protocol was introduced as well as physical changes to the sampling equipment were made to eliminate the airflow and thus the bias conditions significantly. The accounting period which followed, after a phased upgrading process, showed that the accounting between our smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below five per cent relative to theoretical stock).CITATION:Kruger, C J and le Roux, E, 2017. Pitfalls in Vezin sampling for finely crushed materials, in Proceedings Eighth World Conference on Sampling and Blending , pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003