Search Documents

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Frederick Felder

The paper point out the Angostura deposit is located in Colombia. The Angostura deposit, located within the Eastern Cordillera of Colombia is hosted by Triassic-Jurassic quartz monzonite and quartz diorite porphyries emplaced into Precambrian gneisses of the Bucaramanga Group. Silicification, pyritization, sericitization, alunite and pyrophyllite and other alteration and indicator minerals suggest a high sulfidation origin for the strong hydrothermal alteration. Major faults and shear zones occur in the area with NE, E-NE, E-W, WNW, NW and N-S directions. Analysis of geological results and structural modeling has also demonstrated that there is potential for additional high-grade ore shoots within the presently known mineralized structures. Delineating these structures should result in an increase of overall grade and contained ounces.

Apr 22, 2003

IT is not intended that this paper should be regarded as an account of the geology of the Lyell district. It is merely a synopsis of some of the conclusions recently arrived at in regard to the stratigraphic and structural geology, compiled to act as a guide to those members of the Australasian Institute of Mining and Metallurgy attending the Queenstown meeting who are interested in economic geology. The attempt has been made to present certain salient features, omitting a mass of detail, which, although important in the complete investigation and understanding of the economic geology, yet would be confusing to a group of geologists making a short visit. The location of some of the significant occurrences bearing on the main problems and conclusions are indicated in the text in order to enable members to plan the location and direction of their excursions...

Jan 1, 1927

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

The recent paper by Dr. Edwards upon the copper deposits of Australia furnishes a perspective upon that portion of the Commonwealth's mineral deposits which is the more welcome because it has been long overdue. The paper yields in compressed form and in handy arrangement for reference the more relevant data to end of 1938 for all of Australia's important copper deposits 'past"and. present, and for many of the lesser ones. The information supplied 'obviously' has 15een collected' painstakingly and compiled with discrimination.Such published surveys of a national character have been far too few.The Mineral Resources Survey branch of the Department of Supply and Shipping at Canberra has been engaged for several years upon comprehensive compilations of data concerning each of the more important minerals used in industry. Presumably the results will be published after the war. The group will constitute an impressive and valuable series.As yet the work has not been completed, and, for security reasons, much of that which has been finalized is not publicly available. This makes the paper by Dr. Edwards the more timely.In the compilation of data by those not acquainted at first hand with many of the districts involved it is inevitable that, from reading of the literature alone, certain misconceptions will arise relationships become confused; and some of the more recently acquired information unavoidably fail to be taken into account. One need only compare his own impressions of a district, gained from reading the published literature prior to inspection, with the impressions later arrived at following a visit, to realize the difficulties in appraising the various features,in their proper relationships.On the whole, Dr. Edwards has, kept such misinterpretations at a minimum, which is a tribute to the care he must have exercised in analysing the vast fund of data perused. A few errors of statement, mainly concerning, Queensland deposits, have been noted. None is vital, but in the interests of accuracy it seems well to point them out.QUEENSLANDMount IsaOn page 108 Mount Isa's prospective output of 12,000 tons of copper per year is stated as coming from the Doherty section (O'Doherty, Black Rock mine, R.B.),- the copper ore-body is said to occur in dolomitic limestone (-Page 110)-, and Mount Isa's copper output for 1938 from that source is given as 22 tons. On page 145 the same prospective copper output is stated as coming from a body lying out in the hanging-wall of the silver-lead-zinc...

Jan 1, 1943

By William M. Knuth

This study involved a review of bonding and bond release practices in the states of the Eastern and Midwestern Coal Provinces. Data was collected from regulatory authorities and site visits to document the bonding and release procedures in the states related to achieving successful reclamation. The regulations related to PL95-87 were reviewed. The analysis included suggested modified or new bond release criteria, a review of applicable bond release inspection techniques was prepared, a conceptual graduated bonding system and incentive procedures for reclamation of surface mine sites to alternative or higher land uses. A number of conclusions and recommendations for further research were included. A detailed bibliography and a glossary are included in the report.

Jan 1, 1978

By BUREAU OF MINES

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its prin- cipal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctua- tions, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic informa- tion and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that produc- tion rates and reserves have a proportionate relationship.

Jul 1, 1964

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

A new mine has begun production of antimony ore and concentrates in Serbia, Yugoslavia. The mine is operated by the mining and metallurgical enterprise "Aajaca." Initial production is running at approximately 45 thousand tons of ore per year, yielding about 1,500 tons of concentrate. The mine is located on the mountain Kopaonik-Raiceyoj Gori. It is planned to expand production eventually to approach the level of 300,000 tons of ore per year. This level will be a significant addition to the world supply of antimony and will place Yugoslavia among the world's major producers. Currently the United States produces only about 6 percent of its primary requirement for antimony. COBALT -Anglo American Corporation, Ltd. reportedly is considering restarting the Tenke-Fungurume copper-cobalt project in Zaire. Construction on the project was suspended in January because of inadequate financing and political uncertainties. Technical feasibility and financing on a smaller scale than previously envisioned are now being considered. However, an increased copper price may be necessary before any decision to proceed is made.

Jan 1, 1976

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By Ian Gordon Hall

El presente texto describe el proceso de recuperación de las partículas ultrafinas de casiterita en los relaves de la mina San Rafael a través de diversas pruebas metalúrgicas, donde se usaron dos tipos de concentradores centrífugos, los cuales indicaron la posibilidad de una recuperación de 50%, produciendo concentrados de 50% Sn. Asímismo, se instala una planta piloto donde se verifica el proceso de las distintas configuraciones y combinación de equipos, como el efecto de las cargas circulantes. Paralelo a ello, se realizan pruebas para aumentar la ley de los concentrados primarios y así obtener concentrados finales a través de concentración gravimétrica.

Sep 12, 2005

One of the biggest challenges for the mining industry is, quite literally, how to the keep the equipment rolling. There is a limited amount of companies that manufacture the 4.2-m- (14-ft-) tall, 5,670-kg (12,500-lb-) tires needed for the haul trucks that are approaching the 362 t (400 st) pay-load class, such as Terex?s MT6300-AC and Caterpillar?s 797F. And, while these might be the most impressive tires, they are not the only ones that are in short supply. The shortage of tires has affected just about every kind of machine, and the demand for those tires has been extremely high for more than five years with no end to the shortage in site. American Tire Corp. (www.americantire.us) is one of the companies working to supply tires to the mining industry. It announced that the demand for its 1.6-m (63-in.) tires that have a zero failure history globally is great and that the company signed contracts worth more than $500 million at MinExpo. A relatively new player in the field of large tires for mining equipment is Titan Tire Corp., (www.titan-intl.com), a subsidiary of Titan International Inc. It shipped its first 1.6 m (63 in.) off-the-

Jan 1, 2008

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By Joe Pezo

Desde 1999 se desarrollaron pruebas de lixiviación de concentrados en la planta LESDE de Toquepala con el propósito de evaluar las recuperaciones y los tiempos de procesamiento. Las recuperaciones a nivel laboratorio indican que la promoción de la actividad bacteriana es uno de los factores para acelerar el proceso de solubilización del cobre calcopiritico del concentrado. La actividad bacteriana se define como la capacidad de adaptación que tienen las bacterias en medios lixiviantes para elevar la velocidad de oxidación del ión ferroso y convertirlo en férrico y es el mecanismo para la lixiviación del sulfuro primario o calcopirita, el resultado de la interacción de las bacterias ferrooxidantes, el oxígeno y el control de ácido que mantienen un pH por debajo de 2.1. En ese sentido, el presente texto señala las pruebas de lixiviación de concentrados que incluyen estos últimos conceptos, con el objetivo de evaluar la factibilidad técnica y económica de obtener licores de cobre que puedan ser aprovechados utilizando la capacidad existente de extracción por solventes y electrodepositación de la planta LESDE Toquepala.

Sep 12, 2005

By Bobby B. Gillenwater

This report presents recommended guidelines and regulatory changes applicable to electrical installations in underground oil shale mines. These recommendations are based on information gathered from oil shale operators, government agencies, and other knowledgeable sources familiar with existing plans for mining systems and electrical installations, and on present understanding of the problems and hazards associated with oil shale mining. Additional discussions of specific electrical problems related to oil shale mining are also presented. These specific problems include: ? Ground fault current levels ? Permissible electric wheel motors ? Permissible batteries and electric starting systems ? Intrinsically safe instrumentation and applicability of existing test standards.

Jan 1, 1983

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009