Search Documents

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By Moorrees C, Koh P. T, Tsambourakis G

Calcination of samples from the Savage River region of Thsmania containing varying magnesite/dolomite ratios under conditions optimized for the magnesite component, followed by carbonic acid leaching at elevated pressures, leads to leachates of varying composition. For a 3 per cent solids slurry leached at 15.5°C and 700 k Pa carbon dioxide, the leachates have magnesium concentrations in the range 0.71 - 13.2 g/litre. The corresponding magnesium extraction data are 12.5 - 86.4 per cent. The variation in leachate composition would be unacceptable in terms of continuous processing, so that a feed of "constant" composition is essential. Selective mining and physical beneficiation to remove the bulk of the dolomite do not appear to be practical. It is concluded that the most appropriate method of feed preparation is to carry out extensive blending of the magnesite/dolomite ore and the resultant calcine.

Jan 1, 1987

By Enrui Dai, Weibing Chen, Bin Yang, Wenhui Ma, Haisheng Fang, Hui Wang

LiMn0.8Fe0.2PO4/C composite was prepared by an improved solid-state method and the effect of calcination temperature on properties of the obtained materials was investigated. The results showed that increasing calcination temperature from 600 to 700 oC improved the performance of the LiMn0.8Fe0.2PO4/C due to enhanced crystallinity and increased conductivity, but further increase in calcination temperature to 800 oC led to degraded performance due to particle growth and decrease in porosity. Therefore, the LiMn0.8Fe0.2PO4/C composite prepared at 700 oC exhibited the best electrochemical performance, and could deliver a high capacity of 152 mAh g−1 at 0.1 C, 147 mAh g−1 at 1 C and 114 mAh g−1 at 10 C. In addition, the performance of the LiMn0.8Fe0.2PO4/C and LiMn0.8Fe0.19Mg0.01PO4/C was compared when they were obtained at the optimum calcination temperature.

Jan 1, 2015

Norton Co., a manufacturer of abrasive products and diamond drilling and coring bits for oil and gas exploration, is building a $19.1 million addition, scheduled for completion in late 1980, to the Huntsville, AL. The plant makes alumina-zirconia abrasive grains used in grinding wheels and coated abrasives. ALUMINUM Martin Marietta Aluminum Inc. announced plans to expand production capacity of its 112,000-ton-per-year primary aluminum smelter at Goldendale, WA to 177,000 tons per year. The $125 million expansion was scheduled to come onstream in 1981. The Aluminum Company of America announced plans to restart a fourth potline during October at its 185,000-ton-per-year Point Comfort, TX primary aluminum smelter.

Jan 1, 1979

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

global mining boom and in-creased demand for iron ore has lead to a resurgence in the mining industry in Minnesota. At the combined 81st Annual Minnesota Section of SME Meeting and 69th Annual University of Minnesota Mining Symposium, April 15-16 in Duluth, MN, this resurgence was the hot topic as new mining projects were featured in the keynote session. The meeting attracted more than 400 mining industry professionals, including engineers, executives, mining managers and suppliers from around the world. This year?s theme was ?New Ventures in Mining.? The meeting included concurrent technical papers sessions, a keynote session that featured three distinguished speakers and a panel discussion that provided updates on new mining developments in the state. The Minnesota Section of SME technical papers were presented in concurrent sessions, one on mining and one on mineral processing. The mining session included papers on drilling, ore blending, slope stabilization, dust control and operations management. The mineral processing session included papers on plant-control technology, ball mills, pellet strength and fans. Also offered was an SME short course titled ?Simulation based pellet induration optimization.? The Minnesota Section of SME held its annual business meeting during the conference. The 69th Annual University of Minnesota Mining Symposium technical sessions were held on April 15 and also consisted of concurrent sessions on mining and mineral processing. Mining session topics included logistics management, real-time performance measurement, uses for taconite aggregate and environmental issues. The mineral processing session included papers on ore liberation characteristics, zeta potential studies, induration modeling, fuel optimization and conveyor belts. The combined conference included a tradeshow with more than 80 booth spaces featuring vendors offering products and services to Minnesota?s booming mining industry. More than 900 people, including conference registrants and special invited guests of the vendors, at-tended the tradeshow opening reception. This was the largest trade show in many years ? an indication of the vitality of the mining industry in Minnesota.

Jan 1, 2008

By A. Philipp, A. S. Middleton, G. A. Harron, A. B. Durham

"Basal till sampling techniques were used to search for gold mineralization in the Timmins, Ontario area. During 1978 and 1979, approximately 90 overburden sampling drill holes were completed in Murphy and Hoyle Townships to test specific geophysically defined target areas. A conventional tricone dual tube drill system, and a unique retractable tricone/rock coring system were used to various advantages.First pass till sampling at 800 to 1200 ft intervals perpendicular to ice transport direction yielded anomalous gold values in till and carbonatized quartz pyrite-rich bedrock chips, and lateritic soil. Subsequent induced polarization-resistivity surveys defined the areal extent of a pyritic carbonate alteration zone. A second pass till sampling/limited rock coring program evaluated the gold mineralization potential of the alteration zone. Diamond drilling has substantiated the till and bedrock gold anomalies. Further evaluation of this mineralization is currently in progress. IntroductionThis paper describes an integrated geochemical/geophysical gold mineralization discovery case history in Hoyle Township. This discovery is on a property jointly owned (I983) by Canamax Resources Inc. and Du Pont of Canada Exploration Limited. Exploration of the property began in 1978 by Rosario Resources Canada Ltd. and in 1979 a joint venture agreement was signed with Du Pont of Canada Exploration Limited. Rosario Resources Canada Ltd. was taken over by Amax Minerals Exploration in 1981, which became Canamax Resources Inc. in 1982.The work described in this paper deals with a gold mineralization discovery located three-quarters of a mile northwest of the gold deposit currently being readied for underground exploration and development. Further drilling is required to investigate the economic potential of the gold mineralization herein described."

Jan 1, 1987

By Javier A. Llano

GPS, wireless communications and on-board and off-board computing capabilities provide today’s mining companies with unprecedented process improvement and cost reduction opportunities. All aspects of the operation from engineering, surveying, drilling, loading, hauling and support can benefit from products like CAES and Drill Monitor. These technologies, which have been working at world class mines around the world in some cases for over three years, are helping customers achieve new lows in cost per ton. Manually intensive and time-consuming processes like in field surveying are replaced by timely mine status information wirelessly transmitted from the machines to the office.

Jul 17, 2000

By Mahmut Yavuz

to in Old Uighur Turkish as Tolay kopugu, in Ottoman Turkish as Derya kopugu, and in modern Turkish as Luletasi. Scientifically known as sepiolite, it is represented by the formula Si12Mg8O30(OH)4(H2O)4(8H2O). Sepiolite is a natural clay mineral composed of hydrous magnesium silicate, characterized by a structure of alternating blocks and tunnels that develop in the direction of the fiber. Each structural block contains two silica tetrahedral sheets surrounding a central layer of magnesium oxide- hydroxide. Sepiolite exists in two distinct forms in nature: alpha-sepiolite and beta-sepiolite. Alpha- sepiolite is amorphous, compact, and resembles pellets that look like sea froth, hence its Turkish name Luletasi. In contrast, beta-sepiolite appears as amorphous aggregates or small, flat, round particles. These two forms exhibit different physical properties. Meerschaum was also studied by Brauner and Preisinger in 1958, who agreed that it primarily consists of sepiolite (2MgO·3SiO2·nH2O). According to these researchers, water is present in its mineral, zeolitic, crystal, and structural forms. Meerschaum is commonly used for adsorbing various liquids, as an ion exchanger, and for dispersing and insulating paraffin in the chemical industry (Gokdemir and Dogan, 2011). Sepiolite deposits of the meerschaum type are primarily found in Turkey, Somalia, Tanzania, Kenya, and Mexico. Alongside high-quality, low-density, and highly porous meerschaum, Somalia also has sedimentary sepiolite formations. The total reserves of these deposits are estimated at around 50–100 million tons (Sariiz and Isik, 1995). Meerschaum, also known as “white gold” or “sepiolite,” is a unique mineral highly prized for its lightness, heat- resistant properties, and ability to be carved into intricate designs. Found predominantly in Eskisehir, Turkiye, meerschaum mining and processing have become significant contributors to the local economy and cultural heritage. This paper explores the history, economic importance, mining practices, and environmental impacts of meerschaum mining in Eskisehir and discusses the challenges and opportunities faced by the industry.

Feb 1, 2025

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

In 1953, Dr. N. H. Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from the Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of the Institute appointed a Committee consisting of H. H. Dunkin, Associate, Professor of Mining Engineering, University of Melbourne (Convenor), E. A. Rudd, Professor of Economic Geology, University of Adelaide, I. N. Campbell, Chief Geologist of Western Mining Corporation; and the writer to consider and report on this supject.In December 1953, the Committee submitted its first report to the council and this report (reproduced here as an Appendix) was widely circulated among member companies, and engineers, with an invitation to comment on the proposal. A large number of, replies was received and studied.After studying the replies the Committee issued a second report in part as follows:-From these replies we have learned that the suggestions made in the first teport of the Committee are unacceptable to most of those interested, on one or all, of the following grounds;-(a) number of categories,(b) definition of categories;(c) nomenclature.

Jan 1, 1955

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By P G. Self, M D. Raven, R A. Eggleton

Investigation of an abandoned quarry near Rowland Flat in South Australia identified asbestiform antigorite as the fibrous serpentine mineral mined during the 1940s to 1978 for filler applications, not amphibole asbestos or chrysotile as reported in earlier investigations. Scanning and transmission electron microscopy (SEM and TEM) and selected area electron diffraction (SAED) of individual fibres were used to confirm the identification. Chrysotile is widely regarded as the only asbestos mineral in the serpentine group. Further work was done therefore, on the geology and mineralogy of the occurrence, and the health implications were reviewed. A zone of antigorite alteration, with associated talc, is traceable for 750 m along strike of recrystallised dolomitic siltstone within Woolshed Flat Shale of Neoproterozoic age. The antigorite formed, in part, by replacement of prismatic crystals of probable tremolitic amphibole. The deposit is proximal to the Williamstown Fault and the serpentine-talc alteration is possibly due to fluids expelled along the fault during late-stage deformation in the Early Palaeozoic Delamerian Orogeny. The antigorite comprises white to pale green bundles of lath-shaped fibres that occur either as randomly- arranged equant patches after amphibole or as cross-fibre veins, both intimately mixed with calcite. Highly fibrous product was mined from the weathered zone where calcite was leached during weathering. Gentle grinding releases fibres with a high aspect ratio (>10:1) that show a wide range of fibre thickness, including a significant proportion of fibres <0.25 ¦m width. Toxicological studies on fibrous antigorite from Poland and Italy indicate that the carcinogenic potential of this form of serpentine is similar to amphibole asbestos. X-ray diffraction (XRD) and fourier-transform infrared (FTIR) techniques readily distinguish antigorite from chrysotile. Determination of asbestiform habit and confirmation of antigorite mineralogy is most reliably done using electron microscopy, preferably with SAED capability.

Jan 1, 2008

By Louis D. Huntoon

AFTER the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public assayers, but this practice did not prove satisfactory. It was not only difficult to secure a sufficiently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present., small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements

Nov 1, 1909

By Philip Thompson

Many new evaluation tools have been developed since the early 1990’s to aid the minerals processing test engineer. The areas of comminution, gravity concentration, flotation, and process mineralogy have received particular attention. This paper will describe new laboratory procedures in the areas of SAG mill testing, gravity concentration, and flotation testing. Computer assisted mineralogical examination equipment, new generations of mass balancing programs, and simulation programs will also be discussed.

Sep 12, 2005

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014