Search Documents

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By Jean-Philippe Houde

The Blast Furnace Campaign lifetime is highly depending on the wear progress of the hearth lining. This progress is monitored in general through single and double thermocouples at the cold side of the lining. This type of monitoring becomes ineffective as soon as heat resistance will be formed in the refractory lining. Paul Wurth’s monitoring system, consisting of MTP-Sensor and Heat Flux Probes, is able to identify such heat resistances to give a true hearth lining wear. Since last year Paul Wurth is also able to install safely those MTP-Sensor and Heat Flux Probes on running blast furnace without salamander tapping, thanks to a newly developed cooled core drilling device. Blast Furnaces that are equipped with Paul Wurth’s monitoring system have optimized their campaign lifetime as they received right information upon the true wear lining such as detection of heat flux transfer failure, detection and monitoring of brittle layer or detection of hot spot.

Aug 16, 2017

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Armando Vazquez

Steel Dynamics Inc. (SDI) and Tenova Goodfellow Inc. (TGI) have successfully commissioned the first hybrid extractive/laser system for continuous and full spectrum analysis (CO, CO2, O2, H2 and H2O vapor) on two twin shell furnaces at Butler, Indiana. NextGen® technology using off-gas analysis as a main tool for EAF practice optimization is a proven effective method for improving plant productivity. Significant benefits attributed to the NextGen® system are operational cost reductions through the use of real-time dynamic control of chemical energy and improved environmental conditions through reduced GHG emissions. Additionally, the implementation of Tenova’s Water Leak Detection Technology® has shown results as an effective tool for operators to identify in real-time the presence of water during both reducing and oxidizing conditions. This paper will include project details, trials and results and will also outline the latest hardware developments and multipoint capabilities

Oct 30, 2017

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Gabriel Andrade Medeiros, Christian Brugger, Paul Pennerstorfer, Daniel Fuchshuber, Reinhold Leitnerl

State-of-the-art automation technology enables digitalization of the continuous casting process that goes far beyond conventional automation of industrial production. Primetals Technologies provides a digital twin that combines an intelligent digital representation of a casting machine as well as the casting process and the slabs, blooms or billets that are produced. It allows metallurgists and process engineers to predict the behavior of the involved complex production process and optimize parameters before using them in real production. New steel grades or production processes can be evaluated off-line without any risks to process stability and product quality. Primetals Technologies installs the digital twin with every new installation of a continuous caster optimization system. This paper describes how the setup and simulation possibilities of the digital twin provide numerous benefits by modelling and simulating the casting process. It allows for example the calculation of material properties according to the actual composition, strand surface temperature profiles and dynamic soft reduction before the final point of solidification. An outstanding feature of the digital twin is the replay functionality provided for various models to analyze and further optimize real production situations. The paper also gives an example how usage of the digital twin optimized production at a customer.

Oct 1, 2019

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017