Search Documents

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Tobias Krull

The characterisation of iron ore from a materials handling point of view is paramount in order to provide the best possible design for the desired application and maximise equipment uptime at the lowest possible capital and operational expenditure. Problematic issues in materials handling applications often arise in the iron ore industry due to the high density of the ore as well as the abrasive nature of the product. One of the key issues encountered during the handling of iron ore is excessive wear due to either impact or sliding abrasion. The applications and equipment typically affected by accelerated wear issues are mass flow hoppers, transfer chutes and conveyor belts. These wear issues often result in unplanned down times and loss in production which can lead to a considerable loss in revenue. This paper provides an overview of the best practises in the materials handling characterisation of iron ore and discusses available techniques for the modelling of iron ore in applications where accelerated wear is experienced. The application is illustrated through a number of industry relevant case studies for which engineering design work was undertaken to successfully reduce the wear rates of different materials handling equipment.

Aug 1, 2018

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Armando Vazquez Arredondo

Tenova Goodfellow Inc. has successfully installed the proprietary EFSOP® (Expert Furnace System Optimization Process) system in over 80 installations worldwide. For over 15 years, the EFSOP® System has successfully achieved its main objective of improving performance and operating costs through the reduction of electricity, oxygen, methane, injected and charge carbon use. Using the off-gas information provided by the EFSOP® System, Tenova Goodfellow Inc. has now developed a solution for detecting abnormal water events within the EAF steelmaking process. When water form enters the EAF, it immediately forms into water vapor (H2Ogas) and a proportion of the resulting water vapour will further react and dissociate to H2. Effective water detection technology must be capable of detecting BOTH forms of water; H2Ogas & H2. Tenova Goodfellow has the technology to measure in real time and simultaneously H2Ogas & H2. This paper will provide a summary on how the EFSOP Water Detection Technology® is used during the EAF operation. Details regarding the technology, software, alarm rate and information on sensibility water trial tests will be provided within this paper.

Aug 16, 2017

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Jorge Madias

Los hornos eléctricos de arco han sido motivo de una aplicación dinámica de nuevas tecnologías en lo que va de este siglo. La preparación de la chatarra y el uso de materiales de carga alternativos han dado lugar a la concepción de nuevos equipamientos y experiencias en todo el mundo. Surgen nuevos conceptos para el precalentamiento de la chatarra, superando las limitaciones de mantenimiento y ambientales de los conceptos iniciales y mejorando su performance energética. El aporte de energía química para la fusión supera sus límites año a año, requiriendo el desarrollo de equipamiento capaz de una acción rápida y precisa con grandes caudales de gases y sólidos inyectados. Existen nuevas herramientas para eliminar los riesgos de seguridad en la plataforma del horno, haciendo uso de sistemas de enfriamiento más seguros y duraderos, robots, automación de la operación del agujero de colado, y puertas de escoria controladas desde el púlpito.

Aug 17, 2017

By Valeria Romina Stricker

Acerbrag es una empresa Argentina siderúrgica de 50 años de trayectoria, desde el año 2007 pertenece al grupo Votorantim de origen Brasilero. Se dedica a la elaboración de aceros largos para la construcción. La planta industrial cuenta con un proceso de acería integrado, horno eléctrico, horno cuchara y máquina de colada continua. La materia prima es 100% chatarra, característica que la diferencia del resto de las acerías del país. Debido a esto el enfoque principal de este proyecto es reducir el costo de fabricación mediante un “empobrecimiento” de la carga metálica a partir de la flexibilización de los límites de especificación. Esto implica un mayor control del desempeño de los procesos a fin de detectar posibles desvíos, para ello fue necesario implementar la utilización de herramientas estadísticas y gráficas para su monitoreo. La modificación en el mix de fabricación no muestra una alteración significativa en la composición química y propiedades mecánicas de los productos terminados, situación favorable para la continuidad del proyecto. Se observa además, de la reducción de costo esperada, una ventaja en la operación del patio de chatarra y el proceso de acería y en la utilización de chatarras con altos niveles de residuales tales como Cr – Ni.

Aug 16, 2017