Search Documents

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By O. U. Bradley

The utilization of casing-head gas in the manufacture of casing-head gasoline by both the absorption and the compression method is a most important factor in the conservation of our natural resources. Any industry connected with the oil business, in general, possesses particular attraction for a large number of people not conversant with its basic principles, for the reason that the large fortunes made in the production and utilization of petroleum and its products have been given undue prominence. The general impression of the public that enormous profits are to be realized in the casing-head gas industry with minimum expenditures of both capital and effort has, in a large measure, accounted for the phenomenal expansion of the industry in recent years and, likewise, has resulted in many mistakes and loss of investment funds. It is true that many installations have been very profitable, but such instances are always the result of careful planning, experienced judgment and conservative estimates. The inception and subsequent activity in the manufacture of casing-head gasoline, enabling the business to assume an important position in the petroleum industry, are of comparatively recent origin, as its greatest growth, particularly in Oklahoma, occurred during the years 1917 and 1918. Much information must yet be secured and systematized concerning the methods of manufacture of gasoline from high-yield casing-head gas, and a large field is still open for the application of accumulated experience and good engineering practice in devising better methods of extracting gasoline from casing-head gas of the poorer grades. The absorption process is coming into general use as a most efficient system of treating casing-head gas, and even so-called dry gas. In fact, there is a decided tendency toward the universal adoption of the absorption process as against compression methods. However, a general discussion of the relative merits of these two systems is not, within the scope of this article. A few of the facts that must be given 'consideration in arriving at a fair and impartial estimate of the actual investment value of the casing-head gas business are the quantity of gas available, the quality and

Jan 1, 1921

By R. B. Snow

Inclusions revealed by the ultrasonic inspection of forgings, slabs, and blooms cause costly diversion or rejection of the product. Most of those inclusions are so large that they should have floated out of the liquid steel soon after teeming and been removed when the top discard was taken from the ingot. To investigate the source of the relatively large inclusions found in the body portions of ingots, a large forging ingot was examined from top to bottom along the centerline, and special studies were made of open-hearth and BOP ingots. A study of the inclusion distribution in the as-cast 134-inch-diameter forging ingot revealed only a few inclusions larger than 15 microns in the body of the ingot. Larger inclusions may be formed by entrapment of rising inclusions in large falling dendrites rather than by the precipitation and agglomeration of oxides from the liquid steel-dendrite interface during solidification. The original top crust of the ingot investigated broke away from the hot top and sank to the bottom during the solidification process, as indicated by entrapped inclusions found in a band 12-1/2 inches above the stool. A change in the hot-top insulation practice on subsequent ingots to insure the integrity of the top crust has produced clean ingots. A ZrO2 tracer was added to the hot-topping compound and to the top surface of open-hearth and BOP ingots after teeming. The tracer was found in large inclusions in slabs and blooms from these ingots. Large inclusions in the body of ingots appear to be related to disturbances of the natural freezing and shrinkage processes in the hot- top region of the ingot.

Jan 1, 1972

By Howard Hughes

IN drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, . Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,000 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 3, 1915

By D. R. Walker, M. C. Shaw

THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger's law while other data would seem to support Kick's law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative property largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly de- pendent on size. Kick's law is found to hold very well for particles below 1 micron in size, while Rittinger's law holds approximately in the comminution of larger particles. While a physical origin of Kick's law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger's law.

Jan 3, 1954

By E. L. Bruce

GOLD occurs ill many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be confined to representative types of deposits, chiefly those of major importance; a few others, differing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwestern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubtedly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambrian gold deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By M. Gensamer

IN applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "Lüders"' lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiter1 though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By C. H. Jr. Herty

IRON oxide .(Fe0) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon, and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating. slags.

Jan 1, 1928

By John F. Blandy

Every new mining district has had its own peculiar experiences in inventing and experimenting upon new methods for the various operations of mining, and more particularly in the processes of crushing and dressing ores. As a matter of course, during this period many old things have been reinvented, patented, and cast aside, there to remain until at a future day other geniuses shall bring them forth again as new. In this respect the Copper Region of Michigan has not been behind other mining centres, and probably in no other part of the country has more money been expended in devising new machines and improvements upon old ones for the crushing of the rock. The appliances for washing the sand have not been so varied, simply for the reason that, having but one mineral, or rather metal, of high specific gravity to separate from rock material which varies but little in its character in any one mine, it requires much less care than is necessary in most mining centres of the world. At the beginning of operations in that district most of the work was in the control of Cornish miners, who introduced the simplest of Cornish mills, namely, wooden stem pestles, with wooden shafts and cams. These were well suited to the small mines, and particularly to the limited means of transporting more expensive machinery. As these facilities improved, they were enabled to change to iron, and to vary their patterns of rods, shafts, cams, and mortars. The most approved pattern, finally obtained, is the square or round stem, with collar adjustable by means of keys. In its present form it is a bar of cold rolled shafting, an eye in the top, an adjustable collar with key-plate and keys, the head and a shoe of chilled iron. The stem is fitted into the head by a slight taper. The battery has heretofore been of wood, lined with chilled cast plates, and bed-plate of the same, but within the past year the California pattern has been introduced. The screens are of sheet-steel, drilled with 16 holes to the inch. During this period of trial and gradual improvement in the pestle stamps, in the years 1855-6, the Ball steam-stamps were introduced, and after years of labor and expense, have been made the most efficient and powerful machines ever yet used for the purpose. It is ostensibly the Nasmyth steam-hammer, and yet the

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides; polysul-fides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced. are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

By Horace H. Emerich

PrePatory Note.—The first part of this paper was sent to me by Mr. Emrich nearly nine months ago; and I held it, waiting for the second part, which he had promised to forward soon, so that I might submit the whole to some of his former professional associates, and advise him of their criticisms and suggestions before off'ering his work to the Institute. But, five days before the second part reached me, I received by telegraph the news of Mr. Emrich's sudden death. The paper has therefore not had the benefit of such a revision by the author as might have made it ill some respects clearer and more cornplete. Nevertheless, I believe that experts in the branch of metallurgy with which it deals will find it both original and suggestive.—A. Eilers. I. Partial ReFining iN the ANode-Furnace. During my connection with one of the large New Jersey copper-refineries, and probably before that period, from 15 to 30 per cent. of the copper-bullion received was the very foul, leady blister-copper produced from lead blast-furuace matte. It had been customary to mix a small part of this blister with each charge of purer pig-copper, in the effort to dilute it as much as possible before casting into anodes; but tank-house conditions were such that I was led to try making entire furnace-charges of this blister, and refining it as much as possible in the furnace—afterwards casting to anodes and refining elec-trolytically, in tanks and solution separate from the main bulk of the purer copper. In making this experiment, notes were made, for several furnace-charges, of everything thought to have a bearing on the question, and some interesting facts were brought out, both in the furnace-working and afterwards in the tanks.

Jan 1, 1913

By C. W. Hall

Owing to its isolation and comparatively small tonnage, the Yoquivo district is not widely known; though financially important and, geologically, quite interesting. San Francisco dc Yoquivo, the center of the mining district, is in the western part of the state of Chihuahua, Mexico; about 35 miles west of. San Juanito, on the Kansas City, Mexico & Orient R. R. The town can be reached from the railroad by a good trail over a rugged country. The elevation of Yoquivo is 6500 ft., and peaks surrounding the town are 2000 ft. higher. The mining towns of Concheno and Ocampo are 25 miles northwest, and Uruachic is 20 miles southwest. The climate, temperate and healthful, is almost ideal. The rainy season begins in July and ends the latter part of September. There is usually, though not always, some precipitation in all months except April, May, and June: The mountains are covered with pine and scrub oak. Water, wood and lumber are plentiful for all ordinary purposes, and hydroelectric power is available for. about six months of the year, when wood for steam, power is utilized as an expedient. The district has been worked: recurrently for over 60 years. The Yoquivo province lies on the steep western-slope of the Tara-humara division of the Sierra Madre range of mountains. The province is traversed by many deep canyons, most of which flow west. The town is situated on the San Francisco arroyo, which makes a confluence with the Huevachic stream 212 m. southwest; the Huevachic in turn joins the Candemeña river farther down and these two drain the western flank of the Tarahumara mountains and form the headwaters of the Mayo river. The claims of the Yoquivo Development Co., which, is the only organization in the district with a record of any considerable production,: lie within an area roughly 112 m. square. The area extends from the, San Francisco arroyo north, and from the Dolores arroyo west, and is confined to the andesitc formation.

Jan 2, 1926

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.' Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By H. J. Rahilly

MINE FIRES, in the Butte District, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the top of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "Horsetail Ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 2, 1922

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By Robert B. Hoy

To maintain a competitive position in the world market in spite of higher domestic labor costs, the U.S. has been forced to the forefront in developing labor saving devices. This has resulted in automation in our factories, mechanization in our mines, and development of faster and more economical methods of transportation. Since World War II the domestic mining industry has suffered perhaps more than any other sector of our economy. When we assisted our allies-and our enemies-to get back on their feet following the ravages of war we were perhaps overly generous in providing funds and technical assistance to develop foreign mining industries that have since become thorns in the side of our own industry. It has become imperative that domestic industry exert its vigor to meet the challenge of foreign competition. While the domestic industry can meet this challenge of foreign competition in part by protective tariffs, quotas and governmental aid, the most effective way is to maintain technological superiority that will reduce manpower requirements and costs and increase productivity. There is this opportunity both in mineral processing and in mining.

Jan 9, 1962

By Francis L. Sperry

Up to within a few years, the consumption of nickel has been more directly dependent upon the available supply than that of any of the other useful metals. The Gap mine, in Lancaster county, Pennsylvania,* has been, for the last quarter of a century, the only property in this country furnishing nickel in paying quantities. Its yearly output was about 300,000 pounds of metallic nickel, or nearly half the amount used annually in the United States. Foreign nickel from mines on the New Caledonia islands, in the South Pacific, found entrance into our markets as the production of the Gap mine fell off. The price of nickel was constantly maintained, and no special effort was made to extend its use. Over-production was cautiously guarded against, and all surplus metal was held by the banking-houses of the Rothschilds, who assumed the bonded indebtedness of the Sociètè le Nickel. The opening of the Ontario nickel-mines has, however, brought about a radical change; and nickel from the Sudbury district can be delivered in New York within four days, and in European markets within two weeks, as against two months consumed in transporting South Pacific ores. Former prices have been irretrievably smashed, and European trade-journals comment favorably on the influence which Canadian nickel has had in making lower prices, and breaking the backbone of the " nickel trust." Production and Costs. The quantity of nickel produced and the prices which it commanded may be briefly summarized as follows: The total production of the world from 1840 to 1860 was about 100 to 250 tons yearly of metallic nickel; from 1860 to

Jan 1, 1896

By E. Goldin, H. J. Juretschke

THE electrical properties of porous conductors have been studied ever since such materials, usually prepared by pressing and sintering of metallic powders, obtained practical importance. In most cases, however, the results have not been easy to interpret because of the great number of independent variables such as powder size, pressure, pressing rate and temperature, subsequent thermal history, porosity, and so on, which enter into the fabrication of industrially desirable materials. In recent years an interpretation of these properties has become of interest because the electrical properties of many new substances, prepared as fine powders by crystallization from the vapor phase or by reactions in the solid state at high temperatures, have to be determined on porous samples formed from the powder. Since theoretically significant information must refer to the fully dense state of the material, it is important to relate the electrical properties measured on such porous samples to those expected for a sample of 100 per cent density. A simple theory for the porosity dependence of the electrical conductivity and the Hall effect was recently proposed by Juretschke, Landauer, and Swanson.' Their model, assuming a distribution of pores of equal size and shape, sufficiently far apart so that each pore is embedded in a region of uni-

Jan 1, 1959