Search Documents

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." ' This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"' The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By Robert Henderson

Several very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. The Ore Body The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. Mining Systems For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the hanging wall. Between these laterals, at

Jan 1, 1946

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By Reno H. Sales, Charles Meyer

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By Lo-Ching Chang, J. Chipman

The perennial and increasing interest in the chemical behavior of steelmaking slags has led to numerous attempts to formulate the thermodynamic properties of these solutions. The classical view is that of a solution of the component oxides in which certain acidic oxides are more or less completely held in combination with basic or metallic oxides, the nature of the interoxide compounds being derivable from the chemical behavior of the slag or from the mineralogy of a solidified specimen. The known electrical conductivity of slags has pointed to the existence of ions in the solution and a number of attempts have been made to account for the observed facts of slag behavior on the basis of a theory of complete ionization of the solution. It is the purpose of this paper to examine, in the light of ionic theory, a number of recently published series of data on slag-metal and slag-gas equilibria, with the purpose of obtaining a more complete or more satisfactory generalization than has been possible on either of the single bases of simple compound formation or complete ionization. The attempt to formulate the ionic constitution of a complex solution is fraught with many uncertainties. An ion is not something that can be plucked from the solution and examined in detail, nor can its true formula be determined with certainty by any single experimental method. In attempting to express the composition of a slag by various ionic formulas it can be expected that alternative hypotheses of essentially equal merit will present themselves. In the present state of early development of the ionic theory of slags, it may be necessary to make some rather arbitrary choices of ionic formulas in the absence of su- cient information to yield complete certainty. Acids and Bases The classification of slag-forming oxides as acidic or basic apparently dates back into the days of Berzelius. It is difficult to see how the concept could have originated in the early twentieth century when it was fashionable to define an acid or a base as an aqueous solution containing hydrogen or hy-droxyl ions. It is, however, entirely consistent with the modern and more general theory of acids and bases. In this theory, as originally formulated by G. N. Lewis,' a basic molecule is one that has an electron pair which may enter the valence shell of another atom thus binding the two together by the electron-pair bond. An acid molecule is one which is capable of receiving such an electron pair into the shell of one of its atoms. The acid, the base, and the product of neutralization may be either ions or neutral molecules. The product of such a reaction may itself be a base or an acid if it is further capable of giving or accepting an electron pair. Thus a base is a donor of electrons, an acid, an acceptor. In oxide slags the typical and ever-present base is oxide ion, 0-—. In behavior and in importance it is analogous to hydroxyl ion, OH-, which is the typical base of aqueous solutions. There is nothing in the chemistry of slags which is quite analogous to the acid H30+ in aqueous solutions. This is not surprising for in slag systems there is nothing which can be designated as a solvent and no ubiquitous positive ion. The chemistry of slags is in fact more complex than the chemistry of aqueous solutions and the concepts which must be evoked in its study are correspondingly broader. In seeking a basis for a classification of slag-forming oxides as basic or acidic it must be remembered that these terms are not absolute but relative. A substance which acts as a base toward a second substance may act as an acid toward a third. This is less likely to happen among strong bases or acids than among the weak ones; there are numerous examples of weak acids which under the influence of a stronger acid behave as weak bases. Such substances are called amphoteric. A classification of the glass-forming oxides has been proposed by Sun and Silverman² and further developed by Sun3 in which the oxides are arranged in order of decreasing acidity or increasing basicity, each substance being potentially capable of acting as an acid toward substances below it in the list and as a base toward those above it. It is based upon the relative strengths of the metal-to-oxygen bond as determined by the energy required to dissociate the oxide into its component atoms.' Data are available for computation of this energy, at least approximately, for the oxides of slags and glasses. In general those oxides from which it is most difficult to remove the positive atom are the strong acids while those in which it is most loosely held are the strong bases. It is in the latter, of course, that formation of oxide ion occurs most readily as, for example, in CaO which in solution ionizes to form the weak acid Ca++ and the strong base O—. The order of arrangement found by Sun is shown in the first column of Table 1, to which have been added the data for

Jan 1, 1950

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By L. V. Gregor, C. F. Aliotta, P. Balk

The structure of silicon surfaces, thermally oxi&zed in dry oxygen and in steam, was studied using the electron microscope. It was found that the structure on the original (etched) surface is retained at the outer surface of the oxide, whereas the oxide-silicon interface is smoothed out considerably. This supports the idea that, both in oxygen and in steam, the oxidation reaction occurs at the oxide-silicon interface. Mechanical damage of the original silicon surface affects the rate of oxidation. It also changes the chemical properties of the oxide, as shown by the enhanced rate of etching in buffered HF at the locations of damage. However, the oxide at the originally damaged surfaces still exhibits a high electrical breakdown strength. Exposure of thermal oxides to P205 or BzOs vapor, which will yieldphospho- or borosilicate layers, results in complete annihilation of all fine structure on the surface. Reaction of silicon with C02 gives a surface film which probably does not consist of pure SiO,. THERMAL oxidation of silicon yields uniform and strongly adhering oxide films which are normally amorphous and continuous. Contamination and surface imperfections have been reported to cause local crystallization and the formation of pinholes."' The parabolic-rate law of film growth observed by several workers for the oxidation both in steam and in dry oxygen at higher temperatures suggests that diffusion of one or more reactants through the oxide is the rate-deter mining step. One of the dif-fusants is an oxygen species and oxide is continuously formed at the oxide-silicon interface. This was concluded for high-pressure steam oxidation by Ligenza and spitzer5 from an infrared-absorption study of the isotopic exchange of oxygen. Jorgensen arrived at the same conclusion for the oxidation in dry oxygen by measuring during oxidation the resistance change between silicon and a porous platinum marker electrode in the oxide. Recently, Pliskin and Gnall' reported similar conclusions concerning the growth mechanism from controlled etch studies using a phosphosilicate marker. The work communicated in the present paper was aimed at studying oxide growth on locally damaged silicon substrates and relating it to the chemical behavior and electrical breakdown properties of the films. Since etched and oxidized silicon surfaces normally appear to be very smooth when examined by optical microscopy except for some occasional pits, it was decided to use the electron microscope as a tool. In this way, the detection of surface roughness and damage on a scale comparable to or smaller than the thickness of the film is possible. Also, the microstructure of the original substrate surface constitutes a built-in marker which represents a minimum of perturbation to the growing oxide layer, and no foreign material is introduced. Thus information on surface reactions and additional evidence on the location of oxide formation in steam and in oxygen could be obtained. EXPERIMENTAL Electron micrographs7 were obtained using a Philips EM100 electron microscope. Collodion surface replication was used since this is a nondestructive technique and thus permits replicating the same surface at different stages of processing. In order to establish the effect of different treatments it was found essential to make successive observations of the same area by using a reference point. Reference points were conveniently provided by scribing a small v mark on the original surface with a silicon carbide tip. This procedure yields damaged and damage-free areas near the reference point. Upon replication, the samples were thoroughly cleaned before subjecting them to the next process step. Mechanically lapped silicon wafers (Dow-Corning, 100 ohm-cm p-type, cut perpendicular to the (111) direction) were chemically polished in a rotating beaker with a mixture of 1 part HF (48 pct), 2 parts glacial acetic acid, and 3 parts HNO3 (70 pct) by volume. This procedure yields a smooth surface with a faint "orange peel'' structure due to a "ripple" less than 20002i deep. Oxidation in steam or oxygen was carried out in an Electroglas tube furnace. Steam oxidations were always preceded and followed by a brief exposure to oxygen at the same temperattre. The thicknesses of the oxide films under 3000A were determined with a Rudolph Model 436-2003 ellipsometer,' whereas those over 3000A were measured using the VAMFO technique. In the present study, a solution of 300 g of N&F in 25 ml HF (48 pct) and 450 ml water was used to detect areas of increased chemical reactivity in the

Jan 1, 1965

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By D. E. Coates, G. R. Purdy, S. V. Subramanian

The morphological stability of the planar solid-liquid interface in dilute ternary alloys, undergoing steady-state unidirectional solidification, is analyzed in terms of both the constitutional supercooling principle and the perturbation methods recently developed by Mullins and Sekerka. First, various steady-state solutions for the two solute distributions ahead of a planar interface are examined. The nature of the solutions depends on the size and concentration dependence of the off-diagonal diffusion coefficients. W~thin the framework of the constitutional supercooling principle, a cumulative contribution to instability frorn the two solutes is found to exist in the absence of diffusional interaction. It is shown that the latter can produce a further enhancement of instability or can have a stabilizing influence, depending on the form of the liquidus surface and on the sign of the solute-solute interaction. A perturbation analysis, which ignores diffusional interaction, verifies the cumulative influence of lhe solute fields and demonstrates that the Mullins-Sekerka stability criterion for binary systems (with capillarity accounted for) can be readily extended for application to ternary systems. SOME time ago, Tiller et al.' calculated the solute concentration distribution ahead of the planar solid-liquid interface of binary alloys undergoing steady-state unidirectional solidification. An earlier qualitative proposal that the transition from planar to nonplanar growth morphologies is associated solely with the onset of constitutional supercooling in the liquid layer ahead of the moving interface2 was used in conjunction with this calculation to put the now well-known constitutional supercooling (C-S) stability criterion into quantitative terms. Mullins and Sekerka,3 in a recent and very elegant analysis, established a more complete criterion (hereafter referred to as the M-S criterion). Interfacial stability was investigated by determining the time derivative of the amplitude of a sinusoidal perturbation of infinitesimal amplitude which had been introduced into the originally planar shape of the moving interface. Of particular importance is the fact that capillarity was included in the boundary conditions of their calculation. The purpose of the present paper is to extend all of this earlier work on dilute binary systems for application to dilute ternary alloy solidification. The analysis is divided into three sections. In the first the two solute distributions ahead of a moving planar interface are considered. Mathematical solutions are de- termined for situations in which: a) diffusional interaction is negligible, 6) diffusional interaction must be considered but circumstances permit use of constant diffusion coefficients, and c) the concentration dependence of off-diagonal diffusion coefficients can be described by first-order dilute solution approximations. In the next section, a stability criterion analogous to the C-S criterion is developed and the influence of diffusional interaction on interface stability is analyzed. Finally, the perturbation formalism of Mullins and Sekerka, with capillarity included in the boundary conditions, is extended for analysis of ternary systems in which diffusional interaction is negligible. The study of interface stability in binary systems usually commences with the assumption that the equilibrium distribution coefficient and the slope of the liquidus line are constant at values corresponding to infinite dilution. Similar assumptions have not been introduced into the present treatment; that is, we do not assume planar solidus and liquidus surfaces joined by tie lines which yield constant distribution coefficients. The latter involves the assumption of no ther-modynamic interaction between solute species in both the solid and liquid. We consider a ternary phase diagram for which the solidus and liquidus surfaces are, in general, nonplanar and of course pass through the corresponding binary solidus and liquidus lines. These lines are not assumed to have constant slope. In the dilute regions we are concerned with, the following assumptions are made: i) The solidus and liquidus surfaces are of a form such that both the solidus and liquidus temperatures are monotonically varying functions of each solute concentration. ii) The tie lines are such that the equilibrium distribution coefficient of a given solute is greater than unity for every point on the solidus (or liquidus) surface or it is less than unity for every point. STEADY-STATE SOLUTE DISTRIBUTIONS IN THE LIQUID As will be demonstrated in the next section, a knowledge of the steady-state solute profiles is not a necessary prerequisite for the formulation of a ternary C-S stability criterion. However, in that details, such as the complete description of the equilibrium liquidus temperature profile, require an evaluation of the solute distributions, the overall treatment is enhanced if these distributions are determined. Consider a ternary system (solvent plus solutes 1 and 2) for which a planar solid-liquid interface is in unidirectional motion at constant velocity V. At this stage it is unnecessary to limit ourselves to dilute solutions. For a stationary frame of reference the generalized forms of Fick's equations are:

Jan 1, 1969

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By W. E. D. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail- way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews. According to the U. S. Geological Survey, commercial firms photographed 16,291 square miles during 1935, while the Government compiled from aerial photographs by the Geological Survey in the United States 85,544 square miles. It was found that information could be determined in a fraction of the time required by surface methods. However, sounding a word of caution, a Commonwealth of Australia government report on aerial survey operations had this to say: It is necessary to repeat ad nauseam that aerial photographic survey is in no sense a substitute for geological investigation, though it is a very valuable adjunct thereto, and greatly facilitates and accelerates geological mapping. There are many details

Jan 1, 1937

By C. E. Lundin, D. T. Klodt

The binary alloy systems, Y-Ti, Y-Zr, and Y-Hf, have been investigated throughout their entire composition regions. There is no compound formation in any of the systems, and each system is characterized by a single eutectic reaction. The eutectic compositions and temperatures are as follows: A eutectoid reaction pct Y and 870°C occurs in the Y-Ti system, whereas a peritectoid reaction,: pct Y and 880°C occurs in the Y-Zr system. Peri-tectic-type reactions at temperatures above the eutectic levels are postulated for the yttrium and hafnium transfovmations. The development of the technology of yttrium has been given considerable attention during the past few years, and studies of binary phase equilibria have, of course, taken a prominent position in this development. In many respects yttrium, in the third group of metals of the periodic table, is similar to the adjacent group of metals, titanium, zirconium, and hafnium, and the knowledge of the phase relationships of yttrium with these metals is basic to their technology. MATERIALS AND EXPERIMENTAL PROCEDURES Materials. The metals for this investigation were supplied by the General Electric Co., Aircraft Nuclear Propulsion Department. The yttrium was in the form of an arc-melted ingot, and the other metals were in the form of high-purity, iodide-Process crystal bar. Table I lists the purities of these materials. Alloy Preparation. Melting was done by conventional techniques in a nonconsumable electrode arc furnace in an atmosphere of purified argon. Melting conditions for each binary system were the same. Each alloy button was inverted and remelted several times to assure homogeneity. Accurate weights of the charges and resultant alloy buttons were obtained to indicate deviations from intended compositions. No chemical analyses were obtained since melting weight losses were consistently in the range of 0.1 to 0.2 pct of the total weight. 10- or 20-g buttons for each 5.0 wt pct composition increment were melted to survey the three individual alloy systems. Additional alloys differing in composition by 1.0 or 0.1 wt pct increments were also melted to study selected regions of the systems. Metallograpllic Techniques. Standard metallo-graphic techniques were followed for mounting and rough grinding. Preliminary polishing was accomplished using 6-u diamond paste as an abrasive on a Metcloth Lap. Final polishing was done on a Microcloth-covered wheel using 1-u diamond abrasive paste. Purified kerosene was used as a lubricant for both polishing stages. • sothermal- Annealing. Alloys were sectioned for as-cast structlure examinations and then homogenized in preparation for isothermal-annealing treatments. Homo{:enization was accomplished by cold pressing the alloy buttons followed by 72-hr anneals at 1100c. The alloys were encapsulated in Vycor or quartz for the homogenization treatments or for isothermal anneals. Resistance-wound or resistance-element tube furnaces were used for the annealing treatments. The homogenized alloy buttons were cold rolled until cracking occurred or until a -in. specimen thickness was obtained. Small -in. square) specimens for the isothermal anneals were then sawed from the alloys. Each specimen was wrapped in tantalum foil before being sealed in the capsule. Temperatures during the anneals were controlled The time at temperature necessary to equilibrate the structures during the anneals was determined for each alloy system by holding triplicate specimens of alloys at a constant temperature for three different periotls. The specimens were quenched and examined microscopically to determine the number and amounts of phases present in the micro-structure as a function of time. Melting Studies. Eutectic temperatures of the three alloy systems were established from the results of incipient-melting studies conducted on as-cast alloys. Specimens to be melted were suspended on a tungsten wire inside a graphite cylinder placed in a glass vacuum chamber. An optical pyrometer was used to follow the temperature of the specimen as it was inductively heated in a high vacuum. The temperatures were corrected for emissivity losses by standardizing the pyrometer with known-melting-point metals. Accuracy of the temperature measurements is estimated to be + 10°C. The melting point of the yttrium was determined to be 1550°C by this technique. The invariant-temperature levels were also checked by an anneal-quench technique. This technique consists of annealing a series of

Jan 1, 1962

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By Carle R. Hayward

This work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-MiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.l At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages. Preparation of Cu2S.—A piece of cathode' copper from the Buffalo plant of the Calumet & Hecla Co. was cut into shavings by a shaper and converted into sulphide by heating in boiling sulphur. A porcelain casserole was used for the purpose, the heat being furnished by a Bunsen burner. It was found that after boiling in the sulphur for an hour the copper shavings were completely converted into sulphide. The liquid sulphur was then poured off, leaving the solid sulphide in the casserole in

Jan 1, 1915

By John T. Norton, Robert J. Anderson

The purpose of this paper is to report evidence, regarding metal structures, that is contradictory to the amorphous-metal hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby's explanation, is well known and does not require discussion here, but it is advisable to seek the precise meaning of the term "amorphous." According to Beilby, "amorphous means non-crystalline in the most intimate sense of the word; the molecules arc not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when the crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved. The evidence offered here that amorphous metal probably does not exist is of a direct nature and is afforded by x-ray diffraction effects given by a number of metals and alloys when polished, cold-worked, and annealed. Considerable of the experimental work was carried out with substantially pure aluminum and the aluminum alloy duralumin, but many of the observations made on these materials were checked by similar observations on copper, iron, tin, zinc, lead, mild steels, and

Jan 1, 1925

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.' Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.' Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.'. The same condition exists in such sand-tones as the Jones Sand at Shuler' and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955