Search Documents

By K. H. G. Ashbee, J. W. Heavens

One consequence of the distribution in orientation of Bragg diffracting planes in an elastically bent foil is that simultaneous diffraction occurs from ±g pairs, where g is the reciprocal lattice vector to a diffracting plane. If such Bragg contour pairs are indexed, then the variation in orientation with respect to the incident electron beam is known. This note describes a construction by means of which Bragg contour pairs may be indexed by inspection. Referring to Fig. 1, the Ewald sphere radius is l/h, where is the wavelength of the electron beam, and the half spacing of first-order reciprocal lattice planes is l/d, where d is the corresponding spacing in direct space. The angle subtended by the zero and first-order planes at the center of the Ewald sphere is a = sin-' Thus, to represent a pair of first-order Bragg contours on a stereographic projection, measure ±a from, and along the normal to, the zero-order plane. The traces of the required Bragg contours pass through these points and parallel to the zero-order trace. In practice, it is desirable to enlarge a stereographic projection of the zero-order planes before making the construction. As an example, a stereographic projection of first-order Bragg contours up to line 27 for an fcc crystal is given in Fig. 2; if required, higher-order contours can easily be added. Fig. 2 is, of course, a map of first-order Brillouin zone boundaries. One use of this construction is the measurement of large elastic fields in electron microscope specimens. Fig. 3(a) shows a pattern of Bragg contour pairs due to lattice distortions near a large precipitate. This particular example is of a T-phase precipitate in Hidu-minium 54 (A1 + 6 wt pct Cu, 0.5 wt pct Mn). Foil buckling is produced by annealing during observation and may be evidence for evaporation from the precipitate.' Comparing Figs. 2 and 3(0), it is evident that the axis of high symmetry in Fig. 3(a) is [lll]. The strain in a bent foil is approxinlately t/2r, where / is the foil thickness and ? the radius to which the foil is bent. From the projections of grain boundaries and of helical dislocations, it was estimated that ( - 3000A, and values for ? were obtained from the

Jan 1, 1968

By Noel Stearn

OF THE many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. , In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself.

Jan 1, 1928

By John M. McAnerney

In 1955, the U.S. Army started to experiment in Greenland with tunneling in glacial ice and later in frozen glacial moraine. By 1960, long adits and experimental rooms had been successfully excavated. Full mechanization with coal-cutting machinery was most efficient in ice but drilling and blasting were necessary in bouldery moraine. In 1963, the U.S. Army Cold Regions Research and Engineering Laboratory, (USA CRREL; redesignated U.S. Army Terrestrial Sciences Center July 1, 1968) started a tunnel in the frozen silt of central Alaska near Fairbanks. The original adit of 360 ft (109 m) was successfully driven in the permafrost by a twin-rotor tunnel-boring machine, the Alkirk Cycle Miner. The workings were enlarged in 1966 and 1967 by standard mining techniques in which jackhammers, steam points, and augers were compared. A mechanical coal cutter was tried to supplement drilling and blasting. In 1968, airblasting techniques were used successfully for breaking out the frozen silt. All mine products were loaded mechanically and hauled by self-dumping shuttle car. Pneumatic methods of transport were tried for both dust removal and for conveying blast products up to 3-in. maximum size. Studies of the effects of natural winter ventilation through a shaft showed that tunnel closure could be reduced by lowering the adjacent ground temperature. It is concluded that underground openings in frozen ground should be cut and maintained at well below freezing temperatures to hold deformation to a minimum. HISTORICAL BACKGROUND This chapter deals with aspects of tunneling not previously discussed in the conference papers in this book. The chief differences are that the three tunnels lie entirely within frozen material and are relatively small, since they were constructed mainly for research. The primary objectives of the research were to develop underground shelters for military per-

Jan 1, 1970

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Frederick W. Bacorn

The paper of Reno H. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept. But Mr. Sales, for what seem to me to be insufficient reasons, has assumed that there is one deep central source of copper, relatively rich and small, from which all the solutions emanated. From this central source the solutions rose, through one channel or through a group of channels, to the surface, at and within a small area called the central copper zone,

Jan 1, 1915

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958

By Orson Shepard

THE term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 19341. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner:. . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1936

By Frank E. Hall

The needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. SO patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are adjusted so as to give the greatest strength. The fact that the addition of steel scrap, in varying percentages, is the means used to reduce the carbon, together with the fact that a considerable increase in strength results, is probably the explanation of the origin of the name semisteel. That ordinary grades of steel show from three to four times the tensile strength of cast iron is due to the fact that the crystals, or grains, of cast iron are interspersed with flakes of

Jan 1, 1922

By R. A. Walker, R. G. Bradburn, B. C. Flintoff

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit testwork combined with an analysis of operating data showed that (1) metallurgical personnel at times could increase production rates by as much as 10% over that achieved by grinding operators; (2) the chosen data base required an increase of 2% or more to be statistically significant; and (3) for a 2% increase there would be a significant rate of return of investment in computer installation. Consequently one grinding circuit was fully instrumented, and a rented computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long-term objectives. The short-term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been successfully met as described in this paper. Statistically significant increases in excess of 2% have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long-term objectives are (1) off-line analysis of the circuit using mathematical models of process units; (2) on-line experiments to study alternative control tactics; and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1978

By B. Fernow

(Read at the Philadelphia Meeting, February, 1878.) THE question of preserving the forests in this country is an important one, not only to trades using wood but to the whole nation, and though agitated for many years has not received that general consideration which its broad bearing demands. Those who are interested in and working for reform in the treatment of American forests are looking to the government for help, suggesting the creation of a commission to study the conditions of forests at home and abroad, and hope that a sound system of managing the woodlands will be thereby inaugurated. This reform will cost time and money, all the more because the government can bring to bear upon private owners hardly any power but that of good example and encouragement. There is, however, another aspect of the question to which I wish to draw your attention, namely; the more economical use of the valuable material which our forests offer, a more careful and exhaustive utilization of its constituents in all cases where wood or its products are applied. The wasteful consumption of wood in the United States is in every way so enormous as to justify the statement that by merely adopting an economical husbandry in this particular the destruction of forests might be delayed for many years, while the neglect of this imperatively needed and immediately practicable reform deprives legislative remedies of much of their value. In this regard I wish to draw the attention of metallurgists, especially those who are interested in the manufacture of charcoal iron, to a more economical and profitable use of wood in iron manufacture. For thousands of years of human history wood was the main, nay, the only material used for fuel. Mineral coal came into use only in the fourteenth century, and it is only recently that it has largely displaced its less carbonaceous predecessor as fuel. The art of concentrating carbon in the form of charcoal for easier transportation and readier use in distant places was, according to Pliny, known to the ancients long before Christ, and was practiced in all countries, especially in connection with the iron- manufacture.

Jan 1, 1878

By E. C. Dominguez, H. B. Scharf

THE Sparrows Point plant of Bethlehem Steel Co., southeast of Baltimore, is the largest Bethlehem plant, with an annual rated capacity of 6.2 million ingot tons. There is considerable diversity of product, but a high percentage is sheet, tin plate, galvanized sheets, and rod and wire. The large amount of light-weight end product requires a number of pickling installations that necessarily consume large quantities of sulfuric acid. In the coking operations sulfuric acid is also consumed in recovery of ammonia as ammonium sulfate and in treatment of recovered light oil derivatives. Total sulfuric acid consumption in the plant is currently approaching 10,000 tons per month, of which 55 to 60 pct is required for pickling. In 1951 the acute sulfur shortage caused grave concern as to future sulfuric acid supply for the Sparrows Point plant. Raw materials for acid making were already at hand in the form of hydrogen sulfide and pyrites sufficient to produce nearly half the sulfuric acid required at that time. It was also known that the Bethlehem mining activities would produce additional pyrites in the future. Late in 1951 Bethlehem management decided to build a 250-ton sulfuric acid plant at Sparrows Point to utilize these raw materials. The plant was built and put in operation in May 1953. The steel plant has expanded considerably since 1951, and it is now necessary to operate the acid plant far over rated capacity in order to supply plant demand. Production of acid in 1954 amounted to 93,000 tons. Raw Materials for Acid Making: Coking operations at Sparrows Point produce a residual fuel gas in large quantity which has a net heating value of 525 to 545 Btu. Prior to 1950, plant surplus coke oven gas was sold to the local utility company. In

Jan 1, 1957

By Eugene McAuliffe

IT is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the "do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co. has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as "extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go.

Jan 1, 1938

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

By Barry K. McMahon

The fundamental problem in rock mechanics is accounting for the discontinuous and anisotropic nature of the jointed rock mass. It is this problem that makes rock mechanics distinct from the mechanics of steel, glass, or concrete. Existing mathematical models explain much of the behavior of rock cores in the laboratory but, in civil engineering at least, the rocks that matter are the ones that are already broken. On the other hand, the basically descriptive methods now used in engineering geology do not lend themselves easily to mathematical analysis. A set of indices of geological properties related to the strength and deformation characteristics of jointed rock is needed. Like the index properties used in soil mechanics these will probably not have precise mathematical meaning, but once correlations are established with large scale tests they can form a basis for the transfer of test results, obtained in one area under one set of conditions, to the prediction of rock behavior in another area under another set of conditions. Indices of rock properties are even more important in rock mechanics than in soil mechanics as the cost of testing is much higher. To be useful, these indices must be easily and quickly measured and give reproducible results when measurements are made by different people. In this paper the word "joint" means all naturally occurring rock fractures with less than 3 in. of clay or other soft coating material. EXISTING INDICES OF ROCK PROPERTIES A comprehensive review of indices of rock properties for intact rock is given by Deere and Miller.' They provide charts ". . . for estimating the strength or modulus properties for intact rock from the numerical indices obtained by either the Schmidt hammer, the Shore Scleroscope,

Jan 1, 1968

By C. T. Bischoff

This paper describes the results of testing with colorimetric methods, using "dithizone", soil samples taken over various known copper and zinc deposits covered by glacial till. Variation in results is shown for different depths and types of overburden as well as grade and type of deposit. Limiting factors for the practical application of this work are discussed. The method has proved successful for copper and zinc deposits under clay and fine sand with depths up to at least 30 ft but fails in coarse sand and gravel unless depths are very shallow. Swamps require penetration to the underlying subsoil for sample material. DURING the past few years geochemical testing for traces of heavy metals in water, soil, rock, and vegetation has aroused increasing interest. Various techniques for field and laboratory determinations have been described in the literature, as have some of the results of application. However, little information has been published regarding application to glacial terrain. Over 90 pct of the Canadian Shield is overburdened, resulting in high costs for mineral exploration once the outcropping ore deposits have been found. This has been largely responsible for the widespread application of mining geophysics in Canada, permitting concentration of effort on area or zones considered most favorable. However, geophysical interpretation has its limitations, since at least 90 pct of the structures indicated thereby contain no valuable minerals. A more direct approach is therefore highly desirable. If underlying base metal mineralization can be detected by sampling soil or vegetation at moderate cost this should prove of great help in locating new discoveries or extending known ones. A large proportion of Canadian ore deposits contain appreciable copper or zinc, even where these are not the principal economic metals. Consequently the field of application is a broad one. This paper deals with investigations along these lines with particular emphasis on soil sampling. The problems involved from the start were: 1—Which types of glacial soil, if any, would best lend themselves to testing, and conversely which types might be considered relatively hopeless? 2—Through what depths of overburden could significant mineralization be detected? 3—What sampling techniques would prove economically applicable? This included minimum depth of sample and maximum spacing that could be allowed.

Jan 1, 1955

By L. C. Graton

INTRODUCTION CLEAR recognition by Lindgren1 of the important control exerted by physical conditions on the formation of ores laid the foundation for that long-sought attainment, a classification? of mineral deposits based consistently on origin. In probably no other portion of the realm of mineral deposition has the importance of physical influences been so manifest or the validity of Lindgren's genetic classification been so well proved as in that extremely important family of ore deposits which are now universally classed as hydrothermal and generally regarded as of magmatic derivation. While many varieties of deposits, some of them possessing great scientific interest and economic importance, fall outside the limits of this hydrothermal group, inclusion within it of most of the veins and a vast number of the replacement deposits of the world gives to this grand genetic class at once a dominating importance and a powerful scientific appeal. Nowhere are these vein and replacement deposits of hydro- thermal lineage more generously distributed, more extensively exploited or more thoroughly known than in the Cordilleran province of the United States. One of the respects in which these hydrothermal deposits command the interest of both geologists and mine operators is in their relation to depth: the great vertical range through which many of them have already been developed, the disappointing failure of others at relatively shallow levels, and the noteworthy downward changes in character and tenor exhibited by still others. In this hydrothermal category (if the Rand be granted place here) are included the ores of all the very deep mines of the world, ranging from 5,000 to nearly 8,000 ft., as well as of many other mines undoubtedly destined in time to attain corresponding depths.

Jan 1, 1933

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

In the examination of an undeveloped prospect a decision must be arrived at from an inspection of the outcrops and the exposures in a few shallow pits. Prospects that are offered for sale rarely expose any important quantity of good ore, work having usually been stopped when the immediate exploration no longer yielded favorable results. It should be borne in mind, furthermore, that a great majority of prospects have been examined many times, and if of conspicuous promise, would have been acquired-for development. In most cases the problem for the engineer, therefore, is to discover the traces of a valuable mineralization that has disappeared through solution, or the conditions that indicate the possibility, or probability, of underlying secondary enrichments. The available data being meager, every feature should be the subject of careful study-the condition of the outcrop, the structural relationships, the associations of minerals, the alterations of wall rocks, the chances for underlying enrichments, and so forth, as well as the actual assay value of the material exposed. It is frequently advisable to spend the time and money necessary to have trenches dug at various significant points along a promising outcrop; such exposures, even if the depth attained is slight, often disclose conditions that are not apparent at the actual surface, as for example, the existence of soft minerals and the distribution of the various minerals through the mass of the deposit. Trenches also permit samples to be taken from points that were not accessible during former examinations. Strong, persistent outcrops of uniform width may be taken to indicate the probable size and character of the underlying vein,

Jan 1, 1932