Search Documents

By F. B. Richards

For the last five years the furnace-men drawing their oresupply from the Lake Superior districts have had to solve the problem of using the very fine Mesabi ores as part of their oremixture. It is not my purpope to dwell on the early experiences and the progressive development in the use of these ores up to this time, but to lay before the members of the Institute one prominent feature concerning them, namely, the frequent and sometimes very disastrous slips (?) or explosions (?) occurring at furnaces where these ores are used. The Transactions of the Institute contain very little on this subject. Mr. F. E. Bachman, in his discussion of Mr. 0. 0. Laudig's paper (Trans., xxvi., 1061), advances a theory as to the cause of these occurrences; but this is the only reference to the subject in the Transactions up to this time, so far as I can recall. Probably all the furnace-men running the harddriven coke-furnaces in the central West have had more or less experience with this trouble; and I believe the majority of

Jan 1, 1899

By H. C. Fiedler

THE development of the cube-on-edge secondary re-crystallization texture in Si-Fe strip depends upon the ability of inclusions to restrain normal grain growth. This ability is determined by the number and size of inclusions, which, for a given composition, is controlled by the thermal history of the material during the prior processing.' It has been shown2 that increasing the silicon content decreases the solubility of sulfur, and it is the purpose of this note to show the consequences of this decreased solubility for secondary recrystallization. Heats were made as previously described and cast into graphite molds.' The compositions are shown in Table I. Slabs 1 in. thick were cut from the ingots and either hot-rolled from 1000°C in the as-cast condition or after one of the heat treatments described later. The processing to the final gage of 12 mils followed the previous procedure.' To avoid cracking, the 5.2 pct Si alloy was cold-rolled at 150" to 200°C rather than at room temperature. The percent cube-on-edge texture developed by isothermal heat treatments was determined by dividing the maximum torque measured on disk sam-

Jan 1, 1968

By Jack Fox

It is some time since these columns have contained a report to the members on just what is doing in the Society of Mining Engineers. Accordingly, even though it is now a month and a half after the Annual Meeting in Denver, it seems that a report on what transpired at the SME Board Meeting there is in order. First off, I'd like to say that the Members of the Society of Mining Engineers can be justly proud of their representatives on the SME Board of Directors. Of 21 members and officers on the "Old" Board of Directors, 19 were present. President Brower Dellinger chaired the "Old" Board Meeting. Of the 21 members on the "New" Board of Directors, every single one was present. James Boyd, the outgoing AIME President, attended and expressed his appreciation of the support that the Society of Mining Engineers had given him during his year as President of AIME. Members Multiply Robert S. Shoemaker, Chairman of the SME Membership Committee, pointed out that based on figures available, the Society of Mining Engineers had a net gain of 523 members during 1969 while SPE had a 490 net gain and The Metallurgical Society a net loss of 159. This is probably the first time in the last 20 years that anyone has exceeded the SPE net gain in membership. While SME still has a way to go to surpass the Society of Petroleum Engineers in number of members, we did have, on December 1, 1969, 16,369 members. However, 419 were dropped at the end of that month leaving us with a net for the year of 15,950.

Jan 1, 1970

By Charles A. Colton

The results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company's furnace, Port Henry, New York, are given in Tables I and 11. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a 2 inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston," to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solutiou as he states in his description of the apparatus, as many as 50, and sometimes GO, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to canse any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge.

Jan 1, 1879

Prior to any detailed discussion, I'd like to say that Dr. Aplan has made direct hits on two important considerations: 1) The most demanding need in Fine Coal research is to develop improved methods of sulfur reduction. 2) The areas of particle (impurity) liberation and froth flotation hold real near-term promise as techniques for improved sulfur removal. Digressing for a moment, I thin kwe can all remember the time when the biggest problem facing coal research was simply defined - "No money!" In the mid 70's we suddenly found ourselves dealing with a product worth five to seven times the value it carried in the mid60's. All of a sudden, we're talking about a high-profile, high- value commodity. The coal industry still hasn't made the complete psychological adjustment - especially in the operating areas (prep plants included). We have a valuable material at hand which is, in' many cases still being processed as though it were a two or three dollar per ton item. Simply put, I think that while the industry has made some major strides during this transition, a stronger commitment of attitude (and finances) needs to be made toward deeper definition of beneficiation work. Back to specifics - Dr. Aplan has really highlighted three areas where strong research efforts are needed. 1) Liberation processes - not limited to mechanical comminution - must be more fully studied.The industry certainly needs a better handle on value returned (improved ability to beneficiate) for dollars spent on improved liberation. 2) Flotation processes probably hold the most promise for near- term improvement in fine coal beneficiation technology. Dr. Aplan’s.

Jan 1, 1979

By Charles E. Wait

In the analysis of a set of interesting furnace-products belonging to the metallurgical cabinet of the School of Mines, I placed in the hands of one of my students a sample of litharge which gave the results quoted below. The collection of specimens from which this was taken, represents the products obtained in the blast-furnace treatment of argentiferous lead ores, also samples from the zinc process, and those from the cupellation of the enriched lead. The sample, when received, was marked "bismuth litharge," and was that obtained during the last stages of cupellation. It gave upon analysis the following : Per cent. Lead,.......85.36 Antimony,.......06 Bismuth ,........20 Copper,.....49 Iron,...... 69 Zinc,......18 Nickel,.....01 Silver,....2.94 Lime,.....36 Magnesia,....03 Silica,.....12 Sulphuric anhydride,. .32 Carbonic anhydride,. 1.25 Water,.....24 Oxygen,..,.7.80 99.95 At present I wish merely to call attention to the large percetage of silver present (equal to 857 ounces Troy per ton of 2000 pounds avoirdupois), and also to note two or three determinations that I have recently made, with a view to ascertain, if possible, the condition in which this silver exists. If I mistake not, it is usually assumed that silver exists in litharge in the metallic state; and it is, indeed, in the analyses of litharge, rarely expressed otherwise. This method of reporting the silver is, no doubt, due to the accepted statements that the oxides of silver are reduced to the metallic state at a temperature of 300' C. or less. The following experiments lead me to believe that silver exists in litharge, not entirely in the metallic state :

Jan 1, 1887

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980

Wabush Mines is the largest single supplier of iron ore to the Canadian steel industry, with 42% of its 6 million tpy of iron ore production going to the company's two Canadian owners-The Steel Co. of Canada and Dominion Foundries and Steel Ltd. Six other companies hold interests in Wabush Iron Co. Ltd. These are Lykes-Youngstown, Inland Steel Co., Intrerlake Steel Corp., Wheeling-Pittsburgh Steel Co., Finsider of Italy and Pickands Mather & Co. Field work on Wabush began in mid-1957 when a long-range program of economic, geologic, and metallurgical investigations started. This work was followed in 1959 by the construction of a temporary camp and a 700-tpd pilot plant. At the same time, work was also started on a 38-mi railway connection to Ross Bay, Newfoundland.

Jan 1, 1970

By William E. Bonini, Eugene A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey1 for the purpose of delineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Passaic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum.

Jan 4, 1958

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By J. Wright, R. J. Tyler

Changes in the pore structure of hematite pellets during reduction to iron were investigated under a variety of experimental conditions. Pore structures were determined by a mercury penetration technique. The reduction temperature was found to be the major influence on structure, the pore system being bimodal below 7.50°C and unimodal above 900°C. Pore sizes ranging front 0.04 to 20 m were observed in complete metabolized pellets produced over the temperature range 650 - 1050°C. Gas composition and reduction rates also influenced the pore structure of the metabolized pellets, although to a lesser extent than the reduction temperature. An apparent activation energy of 24 kcal/mole was derived for the pore formation process.

Jan 1, 1979

By James Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manu-facturing puzzolan cement; three companies, Birmingham Slag Co., Woodstock Slag Co., and Swann Chemical Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive.

Jan 1, 1937

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

By Paul W. Jeran, Vladimir Adamek

Characteristics of surface deformations i.e., sub¬sidence, inclination, curvature and horizontal strains, are evaluated, based on information obtained by direct field measurements over three longwall panels in the Northern Appalachian Coalfield. Surface deformations have been precomputed using Bals' and Knothe's theories. The results have been compared with Bureau of Mines field data to evaluate the applicability of the two theories to the U.S. min¬ing conditions. Measured horizontal movements and the resulting horizontal strains differ as much as 300 percent from precomputed values. Topography has no detectable effect on vertical movements but appears to have substantial effect on the development of horizontal strains. The horizontal deformations computed from our field measurements generally exceed the limits used in other countries to protect surface structures.

Jan 1, 1982

By V. Lessels, W. A. Hamilton

White Pine Copper Co. is a wholly owned subsidiary of the Copper Range Co. The property of White Pine is about 5 miles south of Lake Superior in Carp Lake Township, Ontonagon County, Mich. The new town of White Pine, adjacent to the company plant, is 18 miles south and west of the town of Ontonagon, and about 55 miles north and east of Ironwood, Mich. A diamond drilling program begun in 1937 to develop the orebody was carried on until 1950. During this period a test shaft, known as the Schacht shaft, was sunk on the orebody and approximately 8000 ft of development drift were driven. In an effort to solve the ore beneficiation problems, considerable metallurgical test work was done on ore extracted through the mine development. This work was conducted in a small pilot plant located in the mill of the Copper Range Co. at Freda, Mich.

May 1, 1956

By Persifor Frazer

IT was my intention to have directed the attention of the members of the Institute to a complete series of rocks representing the older and middle formations represented in Pennsylvania, but time has been insufficient for the purpose, and I have been unable, in the first attempts to reduce the sections of those rocks, which I have brought with me to this meeting, to the requisite thinness necessary for exhibiting the peculiarities of their constituent minerals. The rocks represented here belong to the various horizons already mentioned, and include gneiss, ferruginous gneiss, chlorite slate, quartzites, and hydro-mica slates, limestones, dolomites, ferruginous conglomerates, quartz conglomerates, "Potomac marble" (nether member of the Mesozoic series), dolerites, and a syenite. The order in which these are named is, roughly, the order -of geographical position in a section line from southeast to northwest, commencing at the intersection of the Northern Central Railroad with the Maryland line, and ending a few miles from the town of York, and a short distance within the marginal outcrop of Mesozoic red sandstone. In such a geographical section all the rocks above mentioned would be encountered in the given order except syenite, about which a few words are to be said in a moment. (But this is far from representing the rocks in their geological sequence.) There is nothing of unusual interest to present to your notice in these slates and quartzites. The limestones were carefully searched under 450 diameters microscopic power, but they show no signs of organic remains. One section of a fine-grained Triassic sandstone contains a very beau¬tifully banded plate of quartz. But the objects of greatest interest at present are the specimens of trap. The more fine-grained and compact traps were collected from

Jan 1, 1875

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By E. A. Stevens

IT has been ascertained in recent years that certain rocktypes, geological formations and structural conditions may be used as fairly reliable guides, when prospecting in recognized mineral belts or mining districts, with a reasonable certainty of discovering "pay-ore;" and that such is considered as a practically established conclusion may be inferred from a perusal of the recent reports of the U. S. Geological Survey and the literature of the several scientific societies discussing minim, geology, and kindred subjects. Cripple Creek is no exception to this conclusion, and the rock-type or association, rather than the structural condition, is the most infallible guide.† These guides consist of four, possibly five, dike-rocks, three of which are extremely basic, while the fourth is an acid rock of an entirely dissimilar character. The basic rocks are nepheline-basalt, limburgite, feldspar-basalt and tephrite. There are grounds, however, for believing that the two latter are subdivisions of one type, and therefore will be described under one head. The acid rock is quartz-porphyry. Nepheline-basalt is-a rock encountered in but few localities elsewhere on this continent, and occurs in narrow dikes cutting various formations. When typical‡ it is composed of

Jan 1, 1913

S. LE FEVRE, Forest Glen, N. Y. (communication to the Secretary*).¬F. L. Nason thinks I could not have studied Mr. Witherbee's paper and doubts the arithmetic used, but in his discussion arrives at practically the same conclusion. He says 10 ft. thickness of ore over a square mile should give 27,878,400 tons, allowing 10 cu. ft. per ton of ore. This is correct, but if he reads carefully he will see that this depth of ore was figured as covering one-tenth of the surface, which reduces the figures to those used by Mr. Nason. I did not say, however, that there were 2,300,000,000 tons of ore in New Jersey, but that applying the same method of computation as used by Mr. Nason, to the area of the iron ore-bearing gneisses in New Jersey, we would get a total of 2,300,000,000. I did say, "In this area are located 366 magnetite mines that have been worked more or less. These lenses may easily be capable of producing (on an average) 1,000,000 tons each, and there are probably double the number listed not opened up." Thus my estimate for New Jersey, as far as any was made, would be: Probable ore 366,000,000 Possible ore in addition 732,000,000 1,098,000,000 Mr. Nason's final conclusion of his personal estimate was one-half of what he erroneously read to be the estimate given in the paper, or half of 2,300,000,000, which equals 1,150,000,000. So the two estimates seem to differ less than 5 per cent., and we have the two sister States of New York and New Jersey on an equal footing of productive possibilities in magnetic ore.

Jan 6, 1917