Search Documents

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By Ralph H. Sweetser

IN the recent world-wide deflation of commodity prices the coal industry, including both anthracite and bituminous coal, had reached a level where the actual delivered market prices received by the operators were usually less than the cost of production. Many steel companies and public utilities, operating their own "captive" mines, could have bought coal during the past three years for less money than the true cost of coal produced at their own properties. Competition within the coal industry itself was cruel to the point of profitless operation, and the competition of other forms of fuel was bearing heavily on the coal producers. They were thus forced into methods of production and utilization that they had hitherto ignored; there had been almost complete absence of any appreciation (by the bituminous operators especially) of the necessity of real research work in finding better methods of preparing coal for specific uses, and in finding new and profitable uses for different kinds and grades of coal.

Jan 1, 1933

By R. L. Minckler

PETROLEUM industry forecasts are constantly made and revised but are not in the nature of predictions. Particularly in the field of demand, many of the factors are far beyond control by the producing industry. Supply reacts on demand and demand reacts on supply. Competent economists in the oil business forecasted a year ago, on the basis of experience, that demand would now be at a much lower level than it is. This increased demand increased the price of crude oil and products, and in turn those increased prices have brought forth increased supply. A reduction in demand would lead to a reduction in supply. Shortages are now world-wide, and costs of secondary importance, so if there were extra supplies in California they would be moved into what are termed "unnatural markets." For example, Argentina is in the market today for California gasoline; that is an unnatural market because of the greater transportation distances from California to Argentina than from normal sources.

Jan 1, 1947

By W. D. BRENNAN

AS a rule the thoughts of engineers are more often directed toward the mechanical and physical conditions of mining practice than they are toward the disposition and the marketing of the product. This, I think, has been true of the coal industry to the present time not only among the engineering force but also generally true of operators. There has been a tendency to place the sales department in a rather secondary position; for a great many years there was a greater demand for coal than the supply would meet, so it was only necessary to increase production: either by expansion of operating mines, or opening new mines of greater capacity. While the production of coal is still a highly important phase of the industry, its enormous development throughout the country, the great advance in fuel, efficiency and economy, and the discovery of new reserves of competitive fuels have combined to create a buyers' market and force the present-day attention upon merchandising in modern ways. A buyers' market has a natural tendency to develop the keenest competition, frequently unscrupulous and nearly always profit-wrecking. Under such conditions bad practices are bound to grow and to extend until the industry is wrecked, or until wiser heads get together to reduce or eliminate unfair methods of competition. This is not so recent a condition as one might believe.

Jan 1, 1931

By H. C. Babbitt

The Effect of Arsenic.—A question involving the temperature of precipitation of ammonium phospho-molybdate, which was brought to my attention some time ago, led to the following experiment :*

Jan 1, 1893

By Herty, C. H.

One of the numerous requirements of many grades of present- day steel is that the steel shall be free from non-metallic inclusions. These inclusions may be composed of oxides, sulphides, complex oxy- sulphides, and nitrides, which enter the steel with the furnace charge, result from sulphur absorption from the furnace gases, or are formed in the steel during the deoxidation process. Although few' data are available which indicate in any quantitative manner the specific effects of inclusions in steel, there is a large mass of circumstantial evidence which points to the advisability of producing steel free from these impurities for many purposes. At the present time there is a growing feeling among metallurgists that non-metallic inclusions should be divided into two distinct types: (I) those readily visible under the microscope at ordinary magnifications; and (2) those in colloidal suspension or in solid solution. Both types are profoundly influenced by the character of the charge, the manipulation of the furnace slag, and the method of deoxidation. The work described in this bulletin deals primarily with inclusions visible under the microscope at ordinary magnifications, but the steels made by the various methods of deoxidation are being used LO study certain effects which may be ascribed to the second classification, named above. This latter work will be the subject of further bulletins on the effect of deoxidation practice on the physical properties of the steels involved.

Jan 1, 1957

By PAUL H. SHAEFF

THIS paper is presented with the idea of discussing only the basic open-hearth charge. The importance of the charging operation in producing steel is more clearly understood by dividing the principal components into four groups and discussing each separately, thereby becoming acquainted with what constitutes a charge. The significance of these components in the charge itself will then be taken up. Classification of the charge components is as follows: steel scrap; pig iron ; limestone ; refractories and coke. Steel Scarp The first component, steel scrap, according to size, analysis and cleanliness, may be classified as heavy, medium and light. Heavy melting scrap includes crop ends such as are produced in blooming ingots or the heavy crops from bar mills abovely in. in diameter; railroad scrap, which comprises rails, side-plates, car-frames, draw- bars, etc.; and such automobile forgings as axles, crank- shafts, gears, etc. This class of scrap should give a four-box charging-car (box dimension 24 by 18 by 72 in.) an average load of 10,000 to 20,000 lb.

Jan 1, 1926

By JAMES A. VEASEY

SINCE the World War, excepting for a few brief periods of relief, the American petroleum industry has been obliged to meet its important economic responsibility to this nation hampered by the maladjustment that inevitably follows a marked and unwholesome over-production of its raw material, crude oil. Despite the warnings of the Federal Oil Conservation Board and the endeavors of many of the leaders in the business to stem the flow of oil from the wells of the country, the evil ,not only persists but, at the moment, seems more malignant than ever before. Unless the local and temporary restraints on drilling and production now in effect in California, Wyoming, Texas, and Oklahoma are continued, and, indeed, unless stricter and more comprehensive measures of the same sort are imposed and adhered to by the industry in those States, over-production in the enterprise during the current year will be more pronounced than in any other period in history.

Jan 1, 1929

By Davenport, Edmund S.

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned t for long periods in lamps. In these cases it was noted that the grain bound aries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits arc actually small voids between the grains. The purpose of this paper is to, present the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting is frequently associated with poor performance of filaments in lamps.

Jan 1, 1927

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By E. L. Tucker

PREVIOUS investigations of E. L. Tucker and R. E. Head' related in particular to the effect of cyanogen compounds on galena, sphalerite, and pyrite, and their behavior in the presence of such com- pounds. The present contribution deals with the float- ability of the copper minerals and of pyrite. All experiments were performed on minus 200-mesh material, the method of preparation being the same as that described in the previous article. Flotation tests were made in a small mechanically agitated machine of 50-g. capacity designed in this laboratory by Gates and Jacobsen." General Naval Stores pine oil No. 5 and potassium xanthate were used in constant amount in all of the experiments; these agents were selected because of their present wide use in the flotation of copper minerals. Lime additions were varied to secure four 'final hydrogen ion concentrations, namely, neutral, 0.0005 per cent CaO, 0.003 per cent CaO, and 0.02 per cent CaO. The variation in lime addition was introduced to include the range of alkalinities employed in actual flotation practice.

Jan 1, 1926

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By Cleveland Dodge

THE present organization of Copper Queen employ-ees, known as the Employees' Conference Com-mittee, is really an outgrowth of the former Grievance Committee, which, in turn, had developed from the original Hospital Committee. The relatively small membership of these older organizations, the practical limitation of their activities to the presenting of grievances, and their lack of initiating powers, were the principal defects which the plan now in operation seeks to overcome. A somewhat parallel scheme was instituted in our Sacramento Hill division about four years ago; this gradually developed into the Ways and Means Committee, which, in addition to providing a forum for the discussion of operating problems, was instrumental in establishing an excellent and mutually satisfactory bonus system. Before recommending adoption of the plan now in force, we made extensive inquiries among those who have had any experience in such matters, and ended by proposing a modification of a scheme developed by John Leitch,1 which was characterized by its similarity to the constitution of the Federal Government. As finally remodeled, the. plan was submitted to vote of the entire working forces at the Copper Queen mines, and was adopted by them in May, 1920. Mining opera-tions since that date have been so interrupted that it is scarcely possible to state exactly what the results have been. The following quotations are from a printed pamphlet containing the constitution of the organization, as finally adopted. The first extract is from a letter addressed by the management to the employees: The plan submitted for your approval and adoption is modeled after the constitution of our own country, under which every individual is given an opportunity for advancement, according to his ability and determination, and every citizen is given a voice in the laws that shall govern him. So it is to encourage the individual employee in advancement, and to give him a voice in making the rules that shall govern his conduct, that we favor the adoption of the proposed constitution.

Jan 1, 1923

By J. E. Lamar

THAT Illinois is an important mineral producing state is well known. A value of over $237,000,000 for the mineral products in 1926 indicates the magnitude of the industries. Coal mining is the largest mineral industry, and the value of its product was about 63 per cent of the total mineral production of the state. Oil and gas constituted about 8 per cent and the non-metallic minerals about 29 per cent. This 29 per cent represents the production of a varied group of mineral industries of wide geographic distribution through the state.

Jan 1, 1929

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

By W. D. B. Motter

DURING the early development of blasting with liquid oxygen explosives the trend of experimentation was towards increasing the effectiveness of the explosive. Its characteristic of becoming inert after evaporation of the oxygen content made a strong appeal from the standpoint of safety, especially with missed holes. It later became apparent, however, with practical use of this explosive, that LOX lacked certain other safety characteristics. As its effectiveness was increased, it became more subject to detonation by impact. The object of this paper is to show the steps taken by one operating company to achieve greater safety in the large-scale handling of liquid oxygen explosives.

Jan 1, 1933

By Eugene McAuliffe

The management of The Union Pacific Coal Co., which operates a group of coal mines in Southern Wyoming, believes in the value of applied psychology as a productive factor in the work of getting out coal. Operating almost wholly through the medium of mechanical loading machinery, the company has for some years paid a bonus, equivalent to one-half the labor saving made above a determined average output per shift worked, on a given machine. No penalty is attached where the established output is not obtained, but in 1933 the men on one class of machines earned an average premium of $0.633 per shift on 56.4 per cent of the tonnage loaded. On another class of machine, the men earned an average premium of $0.686 per shift on 28.4 per cent of the tonnage loaded An increase of 36 per cent in tons loaded per man-shift has resulted since the program was instituted. This coal company has also been very successful in reducing mine accidents through prizes awarded in an unusual way. At the close of the year, every man whose particular mine section passes through the year without a lost-time accident is given a ticket entitling him to participate in a safety drawing where an automobile is awarded as first prim.. There are also a number of cash safety prizes which are similarly awarded. Some 1500 persons attend the drawing, which excites much interest and attention. The particular plan employed, the payment of production bonus awards and safety prizes, is foundationed upon collective. rather than individual effort, and, once gotten under way, has proved to be substantlally self-cnforcing.

Jan 1, 1934

By H. C. Rickaby

BY August 1944 Canada expects to be shipping 56 percent hematite ore from its new Steep Rock iron mine, via Port Arthur on Lake Superior, to the steelmaking centers in Canada and the United States. This is indeed welcome news to steel men, especially if they operate open hearth furnaces, as the Steep Rock ore is a high-grade lump and will be valuable as charge and feed ore. But better news is the fact that this first big producer of high-grade hematite ore in Canada, since the exhaustion of the Helen mine in the Michipicoten area north of Lake Superior in 1918, has a proved ore body of 16,757,000 long tons and a probable ore body of 14,000,000 long tons, thus giving an over-all total of 30,757,000 long tons and assuring production for a number of years to come.

Jan 1, 1943