Search Documents

By J. P. Zannaras

If we assume that testing of the model started at time t1, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. I), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t2 after time t2 motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made. It can therefore be stated that all conclusions and observations of the author from the photographs are applicable only to his small-scale experiments and not to actual mine roofs. Without investigation of the true stresses or the combined maximum stress induced in the beds it has been assumed by the author that failure occurred solely due to bending stress caused by loading of the beds. (The author states that D was taken to be the theoretical strain given by elementary beam theory.) Fig. 1 shows that the beds were clamped together. This clamping was necessary to prevent slipping of the beds due to the horizontal shear. However, this clamping caused an uncontrolled and undertermined com-pressive stress S at the end of the beds, and this com-pressive stress caused a true tensile stress ?S (? PoiS-son ratio). This true tensile stress combined with the tensile stress produced at the end of the beds due to loading (fixed beam uniformly loaded), and the horizontal shear which is maximum at the end appears to be the most probable maximum stress produced in the beds. It is therefore evident that the author in performing this experiment has introduced stresses in the model not existing or dissimilar to actual mine roofs, and therefore his conclusions may be applicable to his small-scale experiments but inapplicable to actual mine roofs. Louis A. Panek (author's reply)—The discusser's difficulty is related to mechanics of materials rather than similitude. The effect of time did not enter into the tests in any way, being simply excluded from consideration in this study, because all quantitative results entering into the design equations are based on measured (between time t1 and time t2) bending strains that are well below the breaking strain (i.e., in the elastic range) for the model material. Time does not become a significant factor until the rock stress reaches 80 to 90 pct of the breaking stress." The objective of this investigation was not to predict that bolted roof will fail after time t, but was instead to develop a safe roof, that is, roof in which the bending strain is much less than (say less than 50 pct of) the breaking strain. The models tested to failure had no direct bearing on the design equations. Although for some rocks time may influence the magnitude of stress or strain at which fracture occurs, breaking stress or breaking strain values were not employed for any purpose in this investigation. Tests to failure were made only to obtain additional evidence regarding the behavior of the bolted laminae' as evinced by the locations of the cracks. As stated in the last paragraph of the paper, if one wishes to predict the time or stress conditions for which the roof will fail, additional information is required. The reason for clamping the laminae is to make them behave liked clamped beams, which closely approximate the clamped-plate condition of the actual mine roof beds (Ref. 5, p. 1; Ref. 6). The writer has previously demonstrated that the bending stresses induced by centrifugal loading in a clamped model beam are in agreement with those predicted by theory;' hence clamping has no significant effect on the bending ,trains measured during a test. Moreover, actual ,in, roof beds are likewise subject to a clamping effect due to weight of superincumbent strata carried by the pillars or ribs on each side of the opening. It is emphasized that this study was restricted to evaluating only the reinforcing effect produced by the bolts. Procedures employed in the experiments and in the data analysis were such as to deliberately exclude the effects of other factors. The objections offered are therefore invalid,

Jan 1, 1957

By Hollis Peacock

THE Bingham area in the West Mountain mining district on the eastern slope of the Oquirrh range, some 28 miles southwest of Salt Lake City, has been the most consistent producer for the United States Smelting Refining and Mining Company, production having been continuous, except for minor interruptions, since the organization of the United States Mining Co. in 1899. This production has come from fissures and mantos largely within limestone members aggregating something less than 10 per cent of a thick quartzite sequence of Pennsylvanian age which has been warped into an open syncline plunging northwesterly. Bedding on the easterly limb dips 10°-45° but steep-ens to 90° and even overturns on the westerly limb. Ore bodies cluster about the more northerly of two elongate interconnecting stocks of monzonite which have risen in an axial position within this syncline. Largely within the more northerly of these stocks is the low-grade copper ore body exploited in the Utah Copper open cut of the Kennecott Copper Corp. The values, in seams, minute fracture fillings, and disseminations of pyrite and silica, pervade not only the stock but adjacent sediments, and form a nebulous, sprawling mass which both mineralogically and geographically is the center of the district. The more southerly of the twin stocks appears to be comparatively inert and without obvious relation to mineralization. which

Jan 1, 1948

By Herty, C. H.

Iron oxide (FeO) plays an extremely important part in the manufacture of iron and steel. In the three major processes- blast-furnace, open-hearth, and Bessemer converter-iron oxide is the chemically predominant compound and controls to a large ex- tent the operation of the furnaces and the composition and quality of their respective products. In order to emphasize the importance of iron oxide in each process, they will be considered individually in some detail. THE OPEN-HEARTH FURNACE. Iron oxide is introduced into the open-hearth furnace in four ways : 1. The scrap charged into the open hearth is oxidized by the furnace gases, the amount of oxide formed depending primarily on the amount and type of scrap charged. It has been found' that with large scrap, 1.7 Ib. of FeO is formed per 100 Ib. of scrap charged, whereas with scrap of medium size about 5.3 Ib. of FeO is formed per 100 Ib. of scrap charged, when the period between the charging of the scrap and the addition of hot metal is 3 hours. 2. The decomposition of the limestone sets free CO, by the reaction

Jan 1, 1957

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

By Oliver Bowles

A HEAVY gel of bentonite clay has been proposed as an effective lubricant to speed down the ways to sea, river, or lake, the mighty cargo ships now hitting the water at the rate of about three a day. Another unusual application of a nonmetallic mineral is in food conservation, for the claim has been made that the next new item on the menu for poultry and rabbits will be vitamin tablets prepared from mont-morillonite clay. These uses have minor importance but illustrate not only the diversity in utilization, but the notable trend in 1942 toward mobilizing nonmetallic minerals for the war program. Although occupying less headline space than iron, steel, copper, aluminum, magnesium, and other metals, the nonmetallics are filling important emergency needs. Mica and quartz crystal are essential to communication; asbestos is urgently needed in fireproof heat and electrical insulation; and strontium minerals are utilized in the manufacture of signal flares and tracer bullets.

Jan 1, 1943

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine cool by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 1, 1950

By F. C. Kelley, L. L. Wyman

In order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess binder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the ' contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350" C.

Jan 1, 1931

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere' that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By J. G. Thompson

IRON, iron everywhere, but hardly a particle of pure unadulterated iron for the metallurgist to use as a base for the protean characteristics that he develops in the alloys of iron-the modern steels. Iron, next to aluminum the most abundant metal in the crust of the earth; one of the oldest metals known to man and serving him as the most indispensable metal in both war and peace; yet man's knowledge of its properties is based on specimens that are not pure and hence probably differ considerably in their properties from the truly pure metal. Purification of iron has brought about startling changes in its electrical and magnetic properties and has modified its behavior in changing its crystal form with temperature, the basis of the heat-treatment of iron. So both the research metallurgist and the metallurgist of the steel plant are intrigued by the possibilities that might unfold were 100 per cent pure iron available in sufficient quantities to determine its properties.

Jan 1, 1940

By Charles S. Barrett

NUMEROUS determinations1-7 of the tex-ture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Wever1 and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the roll-ing direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist.

Jan 1, 1940

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the. class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may, at the special request of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, transfer such Member or Associate to the class of Senior Member; and in special cases may waive either the requirement as to age or as to the number of years for which dues have been paid. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified -through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. .SEC. 8. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Affiliate: Upon appropriate action by the Board of Directors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1940

By B. C. Allen, R. I. Jaffee, D. J. Maykuth

Wrought unalloyed iodide chromium, containing 39 to 95 ppm total interstitials, has a tensile transition temperature of —15°C. Re crystallizing at 1100°C causes the transition to rise to 90° to 390°C, depending on the purity, grain size, and cooling rate after annealing. At about the 100 ppm level, individual additions of carbon or nitrogen raise the transition of both wrought and recrystallized chromium by as much as 210°C, while oxygen has a lesser effect, and sulfur essentially no effect. High transitzon temperatures are exhibited by recrystallized and quenched chromium, and appear to be associated with the amount and distribution of inter-stitials. The latter cm be either in solid solution or in the form of precipitates within the grains or at the grain boundaries. Quench hardening in chromium is primarily caused by nitrogen. The hardness, re crystallization, and grain growth behavior of chromium with and without impurity additions were also investigated. BECAUSE of low density and good oxidation resistance, chromium-base alloys are potentially useful for elevated-temperature applications. The main deterrent to the use of chromium in structural applications is its lack of low-temperature ductility, especially in the recrystallized condition. Accumulated evidence has shown that the ductility of chromium is sensitive to purity. The objective of the current study was to determine the effect of common nonmetallic impurities on the tensile properties of high purity chromium. The separate effects of carbon, oxygen, nitrogen, and sulfur additions on the ductile-to-brittle transition were evaluated for wrought and recrystallized material after various cooling rates. EXPERIMENTAL WORK Unalloyed iodide chromium and seven impurity alloys containing individual carbon, oxygen, nitrogen, or sulfur additions were prepared in rod form. Nominal additions were 100 ppm C, N, and S, and 100 to 500 ppm O. The additions were about a factor of ten greater than the residual amounts in the unalloyed material. The seven alloys and two unalloyed compositions were consolidated into four-pound ingots by conventional consumable arc melting of pressed and welded electrodes under 0.5 atm of helium. Impurity additions were made to the electrode in the form of crushed master alloys. The impurity alloys were double melted to improve homogeneity. The ingots were broken down by extrusion at 1200°C in evacuated steel cans at a reduction ratio of 18 :1, using a molten borosilicate glass lubricant and a ram speed of 80 in. per min. The cans were removed by acid pickling, and the chromium core ground free of surface undulations. Cut lengths were sheathed in mild steel and swaged at 900°C until the core was about 1/4 in. in diam. Two additional 15-lb ingots of unalloyed chromium (ICr-3, ICr-4) were prepared by arc melting and broken down by 26:1 extrusion at 1250°C without a steel can. The billet was lubricated and protected from contamination by a coating of molten glass. The resulting extrusion was then sheath swaged as described previously. Representative chemical analyses of each of the materials, after removal of a 10-mil surface layer

Jan 1, 1963

J. W. Tomlison—It seems probable that the author's conclusion, that the conductivity of the slags decreases with increasing content of FeO, is erroneous due to the method of plotting the data. Thus, the results of other workers2,3,13,15 show that the conductivity of molten oxide slags increase with increasing temperature, indicating that the trend of the curve shown by the authors is due to the fact that the data for the slags containing relatively small amounts of FeO are at higher temperatures than those for the slags containing relatively large amounts of this oxide. In this connection the work of Wejnarth2 may be mentioned in which in an investigation of a series of iron silicate slags, the conductivity was found to increase with increasing content of FeO; the fact that the author's slags contained TiO2 probably does not affect the issue since it has been shown15,16 that, at least as far as conductivity is concerned, this oxide behaves essentially the same as silica and that mixtures of the oxide with silica have a very low conductivity of the order of 10-4 mhos at 1750°C. In connection with the experimental technique it may be noted that bubbles of carbon monoxide would probably be produced at the surface of the graphite electrodes in contact with the melts thus rendering the accuracy of the measurements somewhat open to question. J. L. Wyatt (author's reply)—Dr. Tomlinson makes reference to works by Martin and Derge, which indicate that slag systems containing no TiO2 are characterized by an increase in conductivity with an increase in temperature. Further, I have cited his examples, which indicate a drastic increase with small temperature change. The results of Dr. Derge's work have no bearing whatsoever on the results of this paper, since the slags under study here contained up to 70 pct TiO2 One cannot generalize on slag systems as a whole on the basis of any one family, for there are definite compounds of ionic nature formed in each system, and the ionic mobilization of these is something that cannot be determined without actual experimentation. Dr. Tomlinson makes reference to an unpublished work which, he claims, shows that titanium dioxide behaves the same as silica in regard to conductivity. Since I have not had 'an opportunity to see the paper I cannot make any comments, but unless the same slag system was studied there can be no specific comparison of results. If the decrease in conductivity of the slag was due entirely to temperature phenomena, as Dr. Tomlinson indicates, then one is without an explanation of the values shown in the paper for slags containing from 10 to 20 pct FeO. I cannot agree that the deviation in findings was appreciably related to temperature change; further, I believe this point was completely covered in the paper. References 13 Endell and Hellbrügge: Glasstech. Ber. (1942) 20, 277. 14 Bockris, Kitchener, Ignatowicz and Tomlinson: Faraday Society. Discussion (1948) 4, 265. 15 Tomlinson: Thesis, London 1949. 10 Bockris, Kitchener, Ignatowicz, and Tomlinson: Unpublished work.

Jan 1, 1951

By J. L. Wyatt

J. W. Tomlison—It seems probable that the author's conclusion, that the conductivity of the slags decreases with increasing content of FeO, is erroneous due to the method of plotting the data. Thus, the results of other workers2,3,13,14 show that the conductivity of molten oxide slags increase with increasing temperature, indicating that the trend of the curve shown by the authors is due to the fact that the data for the slags containing relatively small amounts of FeO are at higher temperatures than those for the slags containing relatively large amounts of this oxide. In this connection the work of Wejnarth2 may be mentioned in which in an investigation of a series of iron silicate slags, the conductivity was found to increase with increasing content of FeO; the fact that the author's slags contained TiO2 probably does not affect the issue since it has been shown15,16 that, at least as far as conductivity is concerned, this oxide behaves essentially the same as silica and that mixtures of the oxide with silica have a very low conductivity of the order of 10-4 mhos at 1750°C. In connection with the experimental technique it may be noted that bubbles of carbon monoxide would probably be produced at the surface of the graphite electrodes in contact with the melts thus rendering the accuracy of the measurements somewhat open to question. J. L. Wyatt (author's reply)—Dr. Tomlinson makes reference to works by Martin and Derge, which indicate that slag systems containing no TiO2 are charac-terized by an increase in conductivity with an increase in temperature. Further, I have cited his examples, which indicate a drastic increase with small temperature change. The results of Dr. Derge's work have no bearing whatsoever on the results of this paper, since the slags under study here contained up to 70 pct TiO2. One cannot generalize on slag systems as a whole on the basis of any one family, for there are definite compounds of ionic nature formed in each system, and the ionic mobilization of these is something that cannot be determined without actual experimentation. Dr. Tomlinson makes reference to an unpublished work which, he claims, shows that titanium dioxide behaves the same as silica in regard to conductivity. Since I have not had 'an opportunity to see the paper I cannot make any comments, but unless the same slag system was studied there can be no specific comparison of results. If the decrease in conductivity of the slag was due entirely to temperature phenomena, as Dr. Tomlinson indicates, then one is without an explanation of the values shown in the paper for slags containing from 10 to 20 pct FeO. I cannot agree that the deviation in findings was appreciably related to temperature change; further, I believe this point was completely covered in the paper. References 13 Endell and Hellbrügge: Glasstech. Ber. (1942) 20, 277. 14 Bockris, Kitchener, Ignatowicz and Tomlinson: Faraday Society. Discussion (1948) 4, 265. 15 Tomlinson: Thesis, London 1949. 10 Bockris, Kitchener, Ignatowicz, and Tomlinson: Unpublished work.

Jan 1, 1951

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By Maurice L. Pinel, Thomas T. Read, Thomas A. Wright

THE erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1,11,12 but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until more and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: 1. 502 A.D. A pair (right and left) of recumbent lions (Fig. 1). Base 7 ¼ by 14 3/8 in., height over-all 5 ½ in., weight 26 lb. each. The translation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third year of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

By H. O. Hofman

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. IN a previous paper,1 The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation, into the behavior of calcium sul-phate in air; that, is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Moissan,3 and Abbegg,4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851 with carbon monoxide; Gmelin Kraut 5 add Leplay and Laurent (1848) as third investigators. Metallurgical authorities confine their statements to the known fact of reduction by carbon. II. PREPARATION OF RAW MATERIALS. 1. Calcium Sulphate.-This salt was prepared in the same manner as described in our previous paper,6 and was found to be chemically pure. * Professor of Metallurgy, Massachusetts Institute of Technology. + Metallurgical Instructor, Imperial Technological Institute. 1 Trans, xxxix., 628 to 653 (1909). 2 Handbuch der anorganischen. Chemie, vol. ii., part 2, p. 309 (1894). 3 Traité de Chimic Minérale, 1904, vol. iii., p. 543. 4 Handbuch der anorganischen Chemie, vol. ii., part ii., p. 116 (1905). 5 Handbuch der anorganischen Chemie, vol. ii., part 2, p. 233 (1909). 6 Trans., xxxix., 630 (1909).

Nov 1, 1910

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."' * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,' and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956