Search Documents

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By Arno C. Fieldner

METALLURGICAL coke and the by-products of the carbonization of coal continue in strong demand. Nearly 500 new by-product ovens were constructed in 1943. Output of by-product coke in the first ten months of the year was about 2 1/2 percent higher than in the corresponding period of 1942, but beehive production remained on approximately the same level as last year and constituted about 11 per cent of the total coke output.

Jan 1, 1944

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o'clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President's Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep's eyes at New York's other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

By Thunaes, Arvid

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 1, 1950

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By H. S. COOLEY

TO talk about a "factor of economy" in connection with the wire ropes used in mining practice may be coining a new phrase. If such be the case it needs no other apology than that economy in wire rope usage is so bound up with the factor of safety as to justify a similarity in naming that makes one suggest the other. At the latest Wire Rope Research Conference, held under the auspices of the A. S. M. E., Re- search Committee and Engineering Foundation, data were introduced covering mine ropes working under

Jan 1, 1930

By Theodore B. Counselman

Of all natural resources, iron ore made into steel is the most important both in tonnage and value. The primary reason for the prosperity of the United States in the last century has been its pre-eminence in domestic supplies of iron ore and steel. The depletion of these reserves by two world wars and by the demand for richer blast furnace charges, as well as the constantly growing world- wide demand for steel, has fostered the recent quest for new iron ore mines around the globe. These developments have made a dramatic change in the iron ore picture of the world. It is the purpose here, however, to look briefly at the development of the United States iron ore industry, which has played such an important role in the events leading to the modern day boom in iron ore exploration.

Jan 7, 1965

By J. W. Ristori, V. R. Garfias

ONE of the most serious problems now confronting Gel- many-and one that will affect Italy even more seriously if she goes to war against England and France -is that of supplying her navy, mechanized army, and air force as well as her industrial and other needs with the necessary and related products. This problem, serious even now, will become vital should hostilities on a large scale develop.

Jan 1, 1939

By Alicia O'Reardon

DIFFIDENTLY, because don'ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. No doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data.

Jan 1, 1967

By H. I. Aaronson

ONLY limited studies have been made of pro-eutectoid a morphology in hypoeutectoid Ti-Cr alloys during previous investigations, 1-3 The nature of the eutectoid reaction, ß?a + TiCr2, has been considered in somewhat more detail.1,2,4,4 Inasmuch as the proeutectoid ferrite reaction in plain carbon steels has recently been extensively investigated in this laboratory, advantage has been taken of the opportunity to compare the morphologies developed in two rather different eutectoid systems in order to permit a preliminary estimate to be made of the degree of generality which may be ascribed to the various results obtained. Experimental Procedure The chemical analyses of the alloys used are given in Table I. The 7.22 pct Cr alloy was prepared by the Battelle Memorial Institute from iodide titanium and high purity chromium. The initial ingot was made by arc melting a master alloy and iodide titanium. The resultant ingot was twice remelted. by the consumable electrode technique. Upset forging at 950°C reduced the final ingot to 3/4 in. sq bars. The 10.94 pct Cr alloy was prepared by the Titanium Metals Corp. of America from sponge titanium and chromium of ordinary purity. This alloy was melted twice by the consumable electrode technique, forged at 1200° to a 3/4 in. sq bar, and rolled at 815°C to a 1/2 in. round. Specimens 1/4 in. x 1/4 in. x 1/16 in. were cut from the 7.22 pct Cr alloy; halves of disks 1/2 in. in dlam and 1/16 in. thick served as specimens of the 10.94 pct Cr alloy. These specimens were individually encapsulated in Vycor, Each capsule was evacuated three times to a pressure of 2 to 6 x lo-' mm Hg and flushed twice with a reduced pressure of argon prior to sealing. The inclusion of two small packets of zirconium chips permitted the capsules to be outgassed and internally gettered, without heating the specimen, prior to heat treatment. The specimens were solution annealed for 40 min at 1000°C, isothermally reacted in deoxidized lead pots, and quenched in iced water. Most of the isothermal reaction treatments were carried out at 25" intervals between 725° and 550°C on specimens of the 7.22 pct Cr alloy and at 650°C on specimens of the 10.94 pct Cr alloy. Results and Discussion Morphologies of Proeutectoid a*—Kinetics of the ß?a Reaction: Fig. 1 shows the TTT-curves for the beginning of the proeutectoid a and the eutectoid reactions in the temperature range investigated in the 7.22 pct Cr alloy. The M, temperature in this alloy is below 0°C. The curve for the beginning of the proeutectoid a reaction is in good agreement with that of Frost, Parris, Hirsch, Doig, and Schwartz' for a 7.54 pct Cr alloy, appears at considerably earlier reaction times than the corresponding curve presented by Rostoker4 for a 7 pct Cr alloy, and lies athwart the curve of Spachner and co-workers11 for an 8 pct Cr alloy. Differences in criteria for the beginning of the a reaction and the relatively high rate of this reaction at lower temperatures presumably account for some of these divergences and may also explain, in part, the apparent failure of an iodide-base 7.22 pct Cr alloy to react more slowly than sponge-base 7 to 8 pct Cr alloys. Grain Boundary Allotriomorphs: Crystals of this morphology nucleate at and grow preferentially and more or less smoothly along the matrix grain boundaries.5-7 Allotriomorphs are the first morphology to precipitate at most grain boundaries at reaction temperatures from 725°C, the highest temperature studied, at least through 575°C. Fig. 2 Shows typical allotriomorphs, formed during an early stage of transformation at 725°C. Grain boundary allotriomorphs are not the predc=iaant morphology at late reaction times at any temperature studied. However; from 725" through

Jan 1, 1958

By M. H. HARRINOTON

THE Transactions of the Institute afford abundant evidence of the general recognition by mining engineers of the importance of a safety-lamp which will not only give warning of the presence of fire-damp, but will also indicate the proportion in which it is present.' Mining-men are only too familiar with the frequent and sudden changes that constantly occur at the working-face of a gaseous mine. Nothing illustrates more forcibly the pregnant condition of the strata enfolding the seam and the seam itself, than the fact that a circulation of perhaps 150,000 cu. ft. of air may contain 2 or even 3 per cent. of marsh-gas, representing a volume of from 3,000 to 4,000 cu. ft. of this gas pouring-out each minute from the natural strata into the mine-workings. It would, indeed, be strange if this great outflow of gas were always constant, and it creates no surprise that such earth-breathings, as they may be called, are spasmodic and irregular in their wane and flow. There are other causes that act to vary the gaseous condition of mine-air. Gas has a tendency, often very manifest in mine-workings and airways, to stratify and, at times, to travel long distances in veins or streams. It is common to catch and lose the gas in the lamp when making a test. At times two lamps, held side by side in an air current, will indicate different gaseous conditions of the passing air. When testing for gas, the lamp may suddenly fill with flame, in a mine-chamber, where a moment before a careful test showed the presence of but 1 per cent. of gas. It is sometimes remarked that there is little need of detecting a smaller percentage of gas than is revealed by the common

Jan 1, 1906

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By E. P. JENNINQS

(Cleveland meeting, October, 1912.) LARGE deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet 1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archaean schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-deposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained. 1 Chauvenet, Regis, Biennial Report of State School of Mines, Golden, Colo., p. 16 (1886).

Oct 1, 1912

By D. R. THOMAS

GENERALLY speaking, the production of other metals in Mexico fluctuates with that of silver. The first commercial discovery of mineral was in Taxco, Guerrero, in 1552. Five years later, the patio process was introduced at Pachuca, by Bartolome de Medina. In 1884, the main line of the Mexican Central R. R. was completed and a few years later, the National railway. In 1907, the patio process, after 350 years of successful operation, was replaced by cyanidation. Soon after the completion of the railroads, smelters were built at various points and provided means of treating ores that could not be treated by any of the processes existing at that time, such as patio, lixiviation, or pan amalgamation. As a result, a number of mines were developed along the railroads and even far \ out in the mountains. In order to facilitate the shipment of this ore to the smelters, purchasing agencies were established, which for a time were very profitable; most of these agencies are now permanently closed.

Jan 1, 1921

By Archer E. Wheeler

IN the copper industry, the year 1942 was one of striving for larger tonnage and increased production. The demands of the war program placed copper high in the list of strategic metals and the Government encouraged production by offering a premium of 5c. per pound for copper output in excess of the 1941 quotas. This had the effect of increasing the tempo of existing operations and also of initiating a number of projects which will eventually result in production from sources not hitherto exploited. No radically new methods of copper reduction were reported.

Jan 1, 1943

By C. W. Dunham

DESIGN of the structures for the Morenci Reduction Works involved many interesting problems. Naturally, the chief purpose of these structures is to house and support the equipment and other things necessary for or incidental to the conduct of production. hence most of the features of the design were developed to suit these particular conditions; however, several are so generally applicable as to warrant description.

Jan 1, 1942

By F. B. Plummer

PETROLEUM ENGINEERING deals with the production, transportation, and refining of crude oil. Refining is chiefly the work of the chemical engineer; production, that of the petroleum engineer. Production engineering only is discussed in this paper. Petroleum production engineering is closest related to and, in fact, is a branch of mining engineering. Formerly, many petroleum engineers were trained as mining engineers or mining geologists. The profession is related also to mechanical and civil engineering to about the same extent that mining engineering is. Petroleum production draws upon the mechanical branch for drilling and pumping machinery and upon civil engineering for the construction of transportation lines, water supplies, and water-disposal plants. Fundamentally, petroleum production engineering deals with the removal of the oil from the reservoir rocks, just as mining is concerned with the removal of ore. The process of oil production demands a specialized knowledge just as distinct from mechanical and civil engineering as mining is distinct from operating a Diesel engine. Even though the chief tools of the petroleum engineer are the drill and the pump, these may be of little avail, and certainly not efficient, if their selection and use is not based on a knowledge of the physical chemistry of oil, the geology of the formations, the structure of the oil sand, the hydrodynamics of the reservoir, and the interrelation of all these many factors.

Jan 1, 1936

By ARTHUR THACHER

PRIMITIVE man supplied his wants as they arose; as he became more civilized he anticipated them by producing more regularly and storing the products for future use. This tended to cheapen' production and prevent ' violent fluctuations and therefore tended to increase consumption. In order to anticipate our wants, we must know what these wants will be, and this can be .determined only by statistics. 'While we have made great progress in gathering statistics, they are still far from what they should be; especially metal statistics. We determine fairly, well the amount produced, but this does not answer all inquiries because of the erratic conditions of mining, it is necessary to carry larger stocks of metals than of most other articles; moreover, as metals are more or less durable, it is difficult to determine the actual consumption. We often count under consumption what is being produced and sold, while the actual consumption is what is being worn out.

Jan 1, 1921