Search Documents

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

In our sessions devoted to geophysical prospecting, the greater part of the time heretofore has been given to the presentation of theoretical subjects or highly technical details by specialists directly engaged in the development and perfection of the various methods. This was necessarily so, for we wanted such information available for the benefit of other workers and for our members who were anxious to gain a reliable understanding of the principles involved, to enable them to form an opinion of the adaptability of this new technique to their special problems. The methods have now been actively applied by many reliable organizations for several years and in this period there has been opportunity for operating mining men, engineers and geologists to appraise them. We therefore felt that it would be desirable at this meeting to give some time to interchange of opinion concerning results from actual cases. Consequently, the Committee on Geophysical Methods of Pros pecting sent out letters of inquiry to numerous mining people, asking for frank statements of opinion based on results from geophysical surveys at their properties. We have received many replies, among which 30 or more are of specific interest. On the whole, the point of view is remarkably uniform. Except for one or two who were, perhaps, a bit irritated, the operating men who have replied consider the methods to be capable of yielding valuable information when suitable conditions exist. Their attitude is definitely one of tolerance and of confidence in the integrity and sincerity of the outstanding workers. There is, however, a very general feeling that the chances of attaining positive and trustworthy results are small unless the work is directed by, or at least carried on with the close cooperation of, a geologist or mining man who is thoroughly familiar with the local geologic and mineralogic conditions and with the relations of the orebodies to rocks and structure. From certain comments, I am inclined to think that some operators are not greatly impressed with the cheapness of the work. Probably they are not attaching much weight to cost per acre, but are thinking primarily of total cost in terms of significant results obtained. It is

Jan 1, 1932

By Alan Stanley

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—In the analysis of mill products containing minerals of appreciable difference in specific gravity the well-known principle of the method described by Stanley is applied in a number of ways for a variety of problems. The use of Le Chatelier bottle as explained in the paper may be a dependable and sufficiently accurate way, although no information is given as to the reproducibility of the specific gravity determinations. In the case of MacIntyre ore the method is applied for three separate products produced apparently without reagents and relatively free of fine slimes. Should it be applied for flotation products carrying a substantial amount of slimes, difficulties should be anticipated in the process of eliminating air inclusions from the sample. The difficulties mentioned above may be overcome by the use of a volumeter, an instrument designed for specific gravity determinations of finely divided solids in dry state. This instrument, see Fig. 4, is manufactured by F. Süffert-Bürner A. G. in Basel, Switzerland. Its operation is based on the law of Boyle and Mariotte. With the use of the volumeter, the specific gravities of test samples having a total volume of about 30 cm are easily reproducible within ±2 units in the second decimal of the specific gravity figure, and even better than that with utmost care. This accuracy is sufficient for ordinary operational control. How closely the specific gravity determinations follow the respective chemical assays depends primarily on the nature of the sample itself. In this respect no specific gravity instrument can give better results than those justified by the consistency of mineral distribution in samples analyzed.

Jan 1, 1954

By Richard P. Rothwell

The device to which I desire to call the attention of the members of the Institute consists of a water-tight caisson, which is connected By a stuffing-box with the tube to be laid, and the caisson is pushed forward with hydraulic jacks set against the end of the tube. The tube is of hard white iron, cast in chills in segments. These segments are carried from shore through the tube itself, in which a track is laid as the work progresses, and the segments are bolted together in the caisson, where there is ample room to work and proper appliances for handling heavy weights. As each segment is bolted on, the jacks are set against its forward end, and when the whole ring is complete, the caisson is pushed forward by the jacks, a trench having been dredged out in front of it, or, in very loose ground, jets of water under a heavy pressure can be thrown out to loosen the ground in front of the caisson. The direction in which the caisson is pushed is completely under control, and both the caisson and the tube are loaded to the amount necessary to overcome their buoyancy. I understand that Mr. H. H. Hall, of New York, the inventor, is negotiating for the construction of a 16-foot tunnel of this kind across the Straits of' Northumberland, between Prince Edward Island and the main-land, and for tunnels in several other places. 4 One of the most interesting uses of this system is in laying water mains out into lakes. The work can be carried on without inter-

Jan 1, 1886

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By N. A. Gokcen, S. Fujishiro

THE pressures of Mn(g) in equilibrium with Mn7C3 and graphite have been measured by McCabe and Hudson' and Butler, McCabe, and paxton2 by means of graphite, zirconia, and Ta-Mo Knudsen cells. The details of corrections in their measurements were somewhat different from those of the authors;3'4 hence, further independent results at higher temperatures seemed to be warranted. The stoichiom-etry of Mn7C3 in equilibrium with graphite and its stability up to the vicinity of 1373 °K have been satisfactorily established by Kuo and persson5 (See also Hansen and Anderko).' The method of investigation has been described elsewhere in detail.3'4 The carbide was prepared in the manner described by McCabe and Hudson. In order to avoid possible reactions with refractory oxides, only graphite cells were used for the effusion experiments. The authors' results are the runs M-1, M-2 and M-3 listed in Table I, together with those of McCabe and co-workers. The heat capacity, c;, of Mn7C3 is not known; therefore McCable et al. plotted their data as log P vs 1/T and the results were only expressed first' as, and later2 as logP=- -14220+6.06 without further thermodynamic calculations. However, it is possible to estimate closely the necessary heat capacity as follows: When H; - &98 of CrC, or MnO, is plotted vs x, corresponding to various compounds, with temperature as the parameter, it is seen that the relationship is represented by a line of very small curvature. This relationship is also followed by other compounds which do not exhibit solid state phase transformations. In view of the fact that chromium and manganese have the atomic numbers of 24 and 25 respectively, it is reasonable to assume that H; - H;ae vs x for MnC, follows the same type of lines as those for CrC, for which adequate data are available.7 Similar correlations appear to be valid for oxides of two neighboring metals for which reliable data are available. The procedure is thus to move the lines for CrC, vertically (parallel to the axis of HT - H298) until they coincide with the points for MnC1/3, the only carbide of manganese whose H; - HO298 has been

Jan 1, 1963

By Edward Hart

Having occasion several years since to make ferrous sulphide, I attempted to do so by fusing a mixture of coal-brasses (FeS2) and dried ferrous sulphate. A very nice-looking sulphide was obtained; but on attempting to use it, I found that it was insoluble in dilute hydrochloric and sulphuric acids. The subject was laid aside at the time, but has since been taken up; and some curious results have been obtained, which I believe are new. I have made the material by all of the following methods and the product seems to be pretty much the same, however obtained : (a) FeS2 heated to fusion. (b) FeS2, and FeSO4 heated to fusion. (c) FeS2, and Fe2O3 heated to fusion. (d) FeS2, and FeCO3, heated to fusion. (e) FeSO4, and S heated to fusion. (f) Fe2O3 and S heated to fusion. Obtained in this way the mass after cooling breaks easily and is very nearly black in color. On the upper surface of the fused cake the color is generally reddish or brownish black. When this is treated with dilute sulphuric or hydrochloric acid, it refuses to dissolve; but if touched with the point of a file or any piece of wrought-iron, solution of the sulphide takes place with the evolution of sulphuretted hydrogen. If the iron is removed the evolution of gas ceases, and only begins again when the iron is again brought into contact with the fused sulphide. The same thing happens if the iron is connected with the sulphide by means of a platinum wire. But in all the samples of fused sulphide I have obtained, if the iron is allowed to remain in contact with the sulphide for a certain time (which varies with different samples of the fused sulphide) and is then removed, solution of the sulphide continues. Zinc, tin, and magnesium have the same effect as iron. In hydrochloric acid aluminium acts more rapidly even than iron. In sulphuric acid it has little if any effect. Copper in HCl, when brought in contact with the fused sulphide, dissolves quietly without evolution of gas. The solution of copper chloride formed becomes,as it flows down over the sulphide, converted into copper sulphide.

Jan 1, 1887

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

By R. I. Jaffee, H. R. Ogden

AT the present time, there appear to be two conflicting opinions on the solubility of boron in titanium. P. Ehrlich' has indicated from X-ray diffraction work that boron is soluble in titanium up to TiB0.8 (17.8 wt pct, 44 atomic pct). The X-ray diffraction pattern for titanium was found in compositions up to TiB0.05_0.07 (1.1 to 1.6 wt pct); then, without a phase gap, superlattice lines appeared up to TiB0.8 On the other hand, Craighead, Simmons, and Eastwood' have estimated the solubility of boron in both alpha and beta titanium to be less than 0.1 wt pct, based on results of metallographic analysis. In some recent work done at Battelle, results were obtained which shed more light on the titanium-rich end of the titanium-boron system. Iodide-type titanium and high-purity crystalline boron were used in this investigation. The boron was prepared by hydrogen reduction of boron tri-bromide and deposition on a hot tungsten wire. The alloys were prepared by arc melting in an argon atmosphere of 10 cm Hg pressure on a water-cooled copper hearth. The ingots were hot rolled to strip at 850°C. Alloys containing up to 1 pct B could be hot rolled. Those containing 2 pct or more B could not be hot rolled. Metallographically, it was found that a second phase was present in alloys containing as little as 0.4 pct B, and that the quantity of second phase increased with increasing boron content. This is illustrated in Figs. la and lb, which show the microstructures of a Ti-0.4B and a Ti-1B alloy annealed in argon at 850°C. X-ray diffraction patterns of alloys containing 1 and 5 pct B revealed the presence of extra lines which correspond to the superlattice lines reported by Ehrlich.' However, no evidence was found of a shift in the lattice constants of alpha titanium indicating that there is very little, if any, solubility of boron in alpha titanium. This fact, coupled with the fact that the alloys were definitely two-phase, indicates that the extra lines are not superlattice lines, but are more probably the result of a second phase of a hexagonal structure almost identical in cell

Jan 1, 1952

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By ALEX. S. THOMAS

HOWEVER good a furnace may be in regard to design, etc., or however excellent in the quality of the gas used, a suitable heat for the successful working of the metal cannot be obtained unless the melt be coated with a proper quantity of slag. This coating may be excessive or it may be deficient in quantity. The right degree of heat is the essential condition of successful working, for the quality of the steel made is never very good when the metal is allowed to simmer in the furnace for an excessive period, and this heat cannot be obtained if the metal is not protected by a proper covering of slag. This is not only to prevent the metal being over-oxidized and wasted, but also to prevent the metal being chilled when exposed with only a thin covering of slag. The slag may be obtained in either of two ways : 1, naturally, by the presence of sufficient silicon in the iron used, to unite with iron oxide to form a staple slag ; or, 2, by the addition of slag or free silica. In the first case the slag is formed naturally by the action of the oxygen in the flame - i.e., the oxidizing atmosphere of the furnace-on the silicon in the metal when melting. The charge then melts, as it is termed, "thick," and protects the banks from being cut. If too much silicon be present, however, and an excessive quantity of slag be formed, it will be found to be rather infusible, and unless care be taken to add the oxides quickly and follow the furnace up-thus rendering the slag more fusible by the extra iron oxide-the furnace bottom is liable to be pulled up. In such cases the author has frequently been able to warn

Nov 1, 1906

By Donald C. Barton

The elastic earth waves produced naturally by earthquakes have been used for a long time as evidence from which to draw conclusions in ; regard to the constitution of the interior and crust of the earth. The I elastic earth waves produced artificially by occasional explosions and ' recorded by seismological observatories were used to draw conclusions regarding the geology of the intervening area. Intentionally produced elastic earth waves in the past five years have come to be used extensively in the investigation of very local geologic structure. The scismic method of working geologic structure, which makes use of artificially controlled explosions and the resulting earth waves, has developed almost clairvoyant power in handling certain geologic situations; and, in the discovery of salt domes in the Gulf Coastal Plain region of Texas and Louisiana, it has scored the most brilliant success. The first proposal for the use of artificial earthquakes in the study of velocity of elastic earth waves in the surface formations of the earth's crust were made before 1888, by the English seismologists mallet and Abbot. Partly on the basis of their work, A. Schmidt in 1888 proposed the use of time-(Iistnncc graphs of artificial earthquakes to study the variation of vellocity with depth. Belar in 1902 proposed the practical 'application of such investigation in connection with boring tunnels. Galitzcn repeated1y (1912. I9IX) proposed the use of explosions to study the velocity of the longitudinal and transverse waves in the uppermost formations and pointed out that the velocity depended in a high degree on the physical character of the beds and that from changes in the velocity, conclusions could be drawn in regard to the composition of the beds. Somewhat the same thought was proposed by von dem Borne (1908), by Benndorf, Udden and others.' First Use of Artificially Excited Earth waves to Determine Local structure The first application of the use of artificially excited elastic earth waves to thc determination of local geologic structure was worked out,

Jan 1, 1929

By L. A. White

IN this paper it is proposed to follow the developments in the design of the lead blast furnace at Port Pirie from the time The Broken Hill Associated Smelters Pty. assumed control in 1915 to the present time, with special reference to the development of the system using two superimposed rows of tuyeres as is now in operation. Lead smelting operations first commenced in 1889, when the British Broken Hill Pty. Ltd. started its first furnace. This was followed by installing two more furnaces during the same year and another the following year. In 1892, Broken Hill Proprietary Co. Ltd. acquired the smelting works and combined operations with those at Broken Hill, New South Wales; by 1897, the whole of the smelting operations had been transferred to Port Pirie and thirteen blast furnaces were built to treat the Broken Hill ore production. In 1915, The Broken Hill Associated Smelters Pty. Ltd. took over from the Broken Hill Proprietary and have carried out operations since that time. From its inception, the present company started on a long range program of reconstruction, in which the development of the lead blast furnace has played a prominent part. A definite trend in plant development has been towards the simplification of plant control by a reduction in the number of operating units. The great advantages of technical control which resulted from the very simplified flowsheet established in the continuous refining process stimulated the desire to extend the principle to the smelting operation. Thus in the sequence of furnaces described here, it will be noted that the trend has been towards larger and, of course, fewer units. With each such development it is significant that the operating conditions and metallurgical results have shown steady improvement. Standard Furnace In 1920 there were seven furnaces operating, five of a type subsequently called the standard furnace and two of the original thirteen smaller furnaces, the latter type being used for the treatment of drosses, etc. produced from the refinery section, while the standard type carried out the main, lead-smelting operations. The standard furnace (figs. 1 and 2) had the dimensions given in table I.

Jan 1, 1951

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

By Harry V. Welch

This paper presents a brief discussion of numerous devices and processes which have been utilized for the recovery of values from gases in copper reduction works and describes in greater detail the development and application in recent years of electrical precipitation, more familiarly known as the Cottrell process, to the problems of dust losses with furnace gases in copper-smelting and refining plants. The field for collection of suspended particles in gases is widely extended in our modern complex, congested .and industrialized mode of living, and its satisfactory solution is required by our increasing appreciation of the extravagant waste, unhealthful effects and nuisance which such uncontrolled emission of solid suspensions represents. Much of the special dust-recovery equipment in use today has been developed in one industry and carried over to many others. The early work of Cottrell was with sulfuric acid mists, aimed at the purification problem in contact acid manufacture, but the present uses of Cottrell equipment cover a diversified field—carbon black, combustible gas, oil mists, iron blastfurnace fumes and dusts, cement-kiln gases, as well as the purification of gases in contact and chamber acid plants and its wide and extended use in the nonferrous metallurgical field of copper, zinc and lead, and their associated metals. Dust and fume collection from furnace gases became a problem only with the modern development of large and amply powered auxiliary furnace equipment, which in turn permitted large furnace units, fast driving and large outputs of finished product per unit of furnace capacity. The ancient metallurgist with his small clay pot and hand-operated bellows had too little gas velocity to cause a real dust loss. As furnaces grew in size, flues and stacks were added, and undoubtedly the first observable dust losses were indicated by the deposits in the flue and stack base. Large flues, it was noted, collected more than smaller ones, and the expansion of a portion of the flue into a chamber represented the first serious attempt at recovery of furnace dust losses. For a century or more the settling chamber represented the best of skilled metallurgical practice in recovery of furnace dust, and it may be said to have reached

Jan 1, 1934