Search Documents

By S. S. Clarke

LATE in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls Were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1947

By S. S. Clarke

Late in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of Jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of Jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1949

By N. J. Themelis, A. W. Last

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early 1930s in the so-called Hadsel mills (Hardinge, 1955) as seen in [Fig. 1], mainly used in gold mines on the US West Coast. A number of these mills were built in sizes of 6.1 to 7.3 m (20 to 24 ft) in diameter and 1.5 to 1.8 m (5 to 6 ft) in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill, the Aerofall dry grinding mill, and others. A tabulation of all known autogenous and semiautogenous installations around the world was sent recently to the authors by G. J. Kushner of Koppers Metal Processing Division. In the size range of 7.3 to 9.8 m (24 to 32 ft) in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 11.1-m-diam X 4.6-m-long (36-ft-diam X 15-ft-long) mills in Minnesota, powered by 8950 kW (12,000 hp) motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above 150 mills was in operation prior to 1964. Grinding rates in autogenous mills are very sensitive to variations in ore breakage characteristics and even with fairly constant ore type can exhibit large fluctuations in throughput. Autogenous grinding also depends on availability of a fraction of the ore to be ground in the form of "competent" rock which can withstand to a certain degree the tumbling and impact action within the mill. If the ore is uniformly "soft", it will soon be crushed into small size particles and further grinding, which depends on the existence of large size rocks in the mill, becomes impossible. This apparently is the case with most copper ores, as discussed by Bachman, Last and Nabbs (1970) who described pilot testing of a large number of ore samples from Kennecott 's Chino Mines. Under circumstances where autogenous grinding is impractical, it is possible to realize most of its benefits by utilizing large grinding balls in place of the "competent" rock and practice what has become known in the mining industry as semiautogenous grinding. In semiautogenous grinding (SAG), a grate discharge tumbling mill is fed the product of a primary crusher or run-of-mine rock. Forged steel or alloy grinding balls, in proportions ranging from 3.10% of the total volume in the mill, are used to complement the self-grinding ability of the ore. Semiautogenous circuits can be either designed for single-stage closed-circuit grinding which produces a final product for recovery processes, or for two-stage operation in which the SAG mill product is fed to a second stage of grinding in a conventional ball mill.

Jan 1, 1981

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By T. Leffers, A. Grum-Jensen

The development of texture in copper and brass (15 pct Zn by weight) rolled at room temperature and in copper rolled at -196°C has been followed by determination of pole figures for various degrees of reduction. The concurrent development in microstructure has been investigated by transmission electron microscopy. For low deformations, the texture in brass, and in copper rolled at -196°C, is the same as the texture in copper rolled at room temperature. The difference in texture does not show until 50 pct reduction. At the same reduction at which the difference in texture appears, mechanical twinning starts in brass and low-temperature rolled copper. Nevertheless, Wassermann's twinning theory is found to be incompatible with the present resulls. All fcc metals and alloys develop, by heavy rolling, one or the other of two types of texture, classified for convenience as copper type and brass type, or possibly a '(mixed" texture representing an intermediate stage between the two types. The pure fcc metals, except silver, develop copper-type texture by rolling at room temperature. Silver and many alloys, including brass with more than 10 pct Zn, develop brass-type texture.' By rolling at low temperatures a transition in texture from copper type to brass type has been observed for copper of commercial purity.2'3 It is generally accepted that there is a correlation between the type of texture developed and the stacking fault energy. Metals and alloys having fcc structure develop brass-type texture when rolled at room temperature if the stacking fault energy is low, whereas those with higher stacking fault energies have copper-type texture.2 Thus, the difference in stacking fault energy must cause a difference in deformation mechanism responsible for the difference in texture. Of the numerous theories advanced concerning the nature of this difference in deformation mechanism, four seem to be of current interest. Smallman and Greeen,2 Dillamore and Roberts,4 and Dillamore5 refer to the fact that cross slip more easily takes place in a material with a higher stacking fault energy and suggest that the copper-type texture is developed by deformation with extensive cross slip whereas the brass-type texture is developed by deformation without cross slip. Haessner6 has advanced the theory that the copper-tye texture is developed by a combination of normal {111} slip and slip on other planes, mainly 1100). Thus his theory, like the theory above, proposes an additional deformation mode for the formation of the copper-type texture. Contrary to this, wassermann7 and Ahlborn et al.8 believe that the copper-type texture is obtained by normal slip. In their opinion mechanical twins will change a copper texture into a brass texture. For this reason it is suggested that the brass-type texture is developed when, in addition to normal {111}(110) slip, mechanical twinning is present. None of these theories are, however, supported by direct experimental evidence. In a recent experiment Hu et al.9 have followed the development of rolling texture in copper and brass. The texture of copper and brass was found to be es-

Jan 1, 1969

By J. A. Cahill, A. D. Kirshenbaum

Using an alumina or zirconia crucible with an alumina sinker or a molybdenum sinker coated with zirconium dioxide, the density of liquid iron was determined by the immersed-sinker method over the temperature range of 1800" to 2500°K. The density, with respect to temperature, is ex-Dressed by the equation Dg/cm = 8.523 - 8.358 X 10 T'K The molar Volumes and thermal coefficients of expansion were calculated. Iron, upon me1ting, was found to expand 3.5 pct. A basic knowledge of the physical properties of materials at high temperatures is becoming increasingly important. A check of the literature shows, that in spite of the importance of iron, very few measurements have been made of its physical properties in the liquid state. Density measurements have been made by Benedicks and his collaborators1g using the method of balanced columns, by Desch and smith4 using the immersed sinker method with an alumina sinker, by Lucas using the maximum bubble method5 and by Stott and endall' who used an alumina pyknometer. In the method of balanced columns, the difference in level of molten iron in two arms of a U-tube, together with the corresponding difference of pressure had to be measured. The formation of gas bubbles in one or both arms was a great source of error. These values are very erratic. They vary from 6.83 to 7.45 g per cm3 at the melting point (1805"~) and from 6.45 to 7.15 g per cm3 at 1890°K. Stott and Rendall determined the density at 1837"K, with a reproducibility of *0.2 pct. They used an alumina pyknometer fired to 1973°K. The vessel was filled in a vacuum furnace by immersion in the liquid metal. When thermal equilibrium was attained, the pyknometer was withdrawn, cooled, the ingot removed and then weighed. The chief disadvantage of the method was the difficulty of inserting the pyknometer without cracking it. The authors have been able to determine the density of liquid iron from its melting point up to 2500°K, by using the immersed-sinker method, with A1203 or ZrOz crucibles and A1203 or molybdenum sinkers coated with Zr02, Fig. 1. EXPERIMENTAL Apparatus. In these studies the source of heat was the carbon tube resistance furnace with an argon atmosphere described previously.7 Experimental runs were made using either Ala3 or ZrOz crucibles. The sinkers used were 1) pure A1a3 and 2) molybdenum coated with ZrOz. The crucible, 2 1/8 in. in diam and 3 in. high, was centered in the furnace on an Ala3 of Zr02 pedestal. The sinker, 1/2 in. in diam and 1 1/2 in. long, together with a counter weight, was suspended from an analytical balance into the melt by a molybdenum wire. Procedure. The procedure, as described previously,' consisted in measuring the weight loss of the sinker in the liquid iron while determining simultaneously the liquid iron temperature by means

Jan 1, 1962

By P. P. Scott, George C. Howard

A field remedial procedure utilizing a kerosene-cement slurry as a water plug-off agent in fractured formations was evaluated both in the laboratory and in the field. This procedure has proved to be capable of effectively shutting off water without causing permanent impairment of the oil production. Success was attributed to the fact that an immobile cement slurry, when placed in a water-producing strata, will set and form an impermeable barrier; whereas when placed in an oil-producing section the cement will retain a relatively high permeability and may be removed by acidizing. INTRODUCTION One of the most perplexing problems facing the oil industry is the selective exclusion of water production from oil or gas-producing wells. This problem has been studied by many investigators in an attempt to develop a material that is not only capable of reducing water production but is also capable of being selective in that it will not impair oil production in either fractured or intergranular type reservoirs. A study of these two types of formations indicated that two distinct types of materials for controlling water production might be required — a completely liquid plugging agent for intergranular formations and a semi-liquid or slurry type plugging agent for fractured formations. This paper is limited to the control of water production from fractured formations. A common source of water in the vicinity of oil bearing rock reservoirs is water which previously has entered and, because of its higher density, generally lies near the bottom of the formation. When the deepest point of penetration of a well into such an oil and water-bearing formation is above the level of the water, and the dynamical gradients due to the flow of oil overbalance the difference in densities between oil and water, water production becomes a problem. Then the water level rises in the shape of a cone and is produced from the lower depths. Other investigators1,2,3,4 have developed theories which define the pressure gradients and contours of this cone in a homogeneous formation and have shown that the placement of a plug in the bottom of a well is only slightly effective in temporarily reducing the flow of water. Assuming that the manner of flow of bottom water from fractured formations to a well is generally similar to the flow in homogeneous formations, then it would be expected that some form of coning, perhaps of less symmetry, would also occur. Then, because of the similarity of the manner of flow of water, placement of a vertical plug in a fractured formation would also probably be ineffectual for controlling water production. However, as has been shown by electric model flow study,' the placing of a plug in a well and an impermeable horizontal streak in the formation might prove to be a means for materially reducing or even eliminating water production in a fractured formation. An indication of the difference in effectiveness between horizontal and vertical plugs based on theory developed from study of the flow of water and oil in rock reservoirs is depicted in Fig. 1. These curves show the expected

Jan 1, 1955

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By C. F. Knutson, Martin Felsenthal, J. D. Lung, J. D. Sudbury

This paper has been written to summarize the laboratory and field studies leading to injection of Pacific Ocean water into the Third Grubb formation. Laboratory tests for studying the permeabilities of cores to Pacific Ocean water are described. Resu1ts of these tests showed that the water could be successfully injected if it is chertzically stable, sterile, and properly filtered. Clay swelling was shown to be a comparatively minor factor in permeability reduction. Studies leading to development of an economical system for properly conditioning the ocean water are discussed. It was necessary to control pH, calcium carbonate deposition, bacterial growth, iron solubility. oxygen, and suspended .solids. A relatively simple system combining the use of sulifur dioxide, a quaternary rlmmonium chloride, and filtration was shown to adeqrrately control all these factors. This combination has not previozrsly been used as a water treating technique. Evaluation tests of the water conditioning system prior to injection are described, and results of such tests are presented. Control measures needed to insure a continusously adequate water treatment are reviewed. INTRODUCTION The utilization of sea water for waterflooding has only recently been attempted. Knowledge of treating requirements has been limited, and in most cases no water treating has been done. Prior to the initiation of the Third Grubb zone pilot water flood at Ventura, Calif.,1,2 extensive laboratory research was done in an effort to define the treatment necessary to provide a suitable injection fluid. Close coordination and cooperation between field and research personnel were found to be the foremost requisites in developing the most economical and practical method for treating ocean water. LABORATORY STUDIES Plugging Tendencies of Untreated Ocean Water A program of laboratory studies was initiated for the purpose of evaluating whether ocean water could be injected into the formation for prolonged periods of time without causing plugging of the pore spaces of the formation. Because of the fairly low permeability of the formation (averaging about 40 md), it was realized from the outset that a water of exceptionally high quality was needed. Ocean water used in the laboratory studies was carefully filtered through ultrafine fritted glass filters, having nominal maximum pore sizes of 1.4 microns. Permeability tests were then performed on representative core material from the formation. It soon became apparent in these tests that filtration alone was not a sufficient treatment for the ocean water. Prolonged injection of the filtered water caused rapid plugging of the core samples. The permeability decline of a typical sample is illustrated by Curve A in Fig. 1. The several factors which can contribute to this plugging tendency are briefly reviewed below: Interaction with Formation Clays An evaluation of clay swelling effects on liquid permeability was made using core samples from the Grubb formation. An oil was chosen for determining the reference liquid permeability because it would not tend to react with any clays that might be present in the formation. The samples were then extracted, dried, and resat-urated with either treated ocean water, formation water, or fresh water. Permeabilities to the various waters were then determined. Results of this test series are summarized in Fig. 7. The difference between the oil permeability and water

Jan 1, 1957

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.&apos; It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.&apos; The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.&apos; The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the metallurgy, fabrication and uses of the nonferrous metals and their alloys; to represent the A. I. M. E. in so far as nonferrous metallurgy is concerned, within the rights given in A. I. M. E. By-law XI., Sec. 1, and not inconsistent with the Constitution and By-laws of the A. I. M. E.; to hold meetings for social intercourse and the discussion of nonferrous metallurgy; to stimulate the writing, presentation and discussion of papers of high quality on nonferrous metallurgy; to reject or accept such papers for presentation before meetings of the Division. Article II—MembeRs Sec. 1. Any Member, Associate, or Junior Associate of the A. I. M. E. in good standing may become a Member, Associate or Junior Associate of this Division upon registering in writing a desire so to do, but without additional dues. Sec. 2. But no one who has been continuously indebted to the A. I. M. E. or to this Division for more than three months shall be entitled to vote or to receive publications to which, as a member of the Division, he would be entitled. Article III—Funds Sec. 1. The expenditure of the funds reccived by the Division shall be authorized by the Executive Committee of the Division. Article IV—Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the A. I. M. E., and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the A. I. M. E. Sec. 2. The annual business meeting for election of officers shall be held within a few days before or after the annual business meeting of the A. I. M. E. Sec. 3. At any meeting of the Division for which notice has been sent to the members of the Division through the regular mail at least one month in advance, a business meeting may be convened by order of the Executive Committee, and any routine business transacted not inconsistent with these By-laws or with the Constitution or By-laws of the A. I. M. E. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. Article V—Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, two Vice-chairInen, Secretary and Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, in so far as is consistent with the By-laws of the Division and the Constitution and By-laws of the A. I. M. E. Institute of Metals Divisiori

Jan 1, 1931

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may&apos; be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as &apos;could be expected without railroad transportation

Jan 1, 1924

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device. When the management decided to start open- pit operations in 1945 the ruggedness of the terrain was one factor that led to the purchase of the small 22-T model drill. The orebody lies on both sides of Copper Creek Canyon. The sides of the canyon are steep and are cut by numerous narrow branch gullies. The drill had to travel over roads that were narrow and steep. It proved adequate for drilling the capping formation and is still in use.

Jan 1, 1950

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement&apos; affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911