Search Documents

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.'' Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystal-line powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.' In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962

APRIL BEGAN with increased disorder in the Ruhr and some blood-shed. The war cloud in the East disappeared, however, with the signifi- cance by the Turks of their intention to return to Lausanne to negotiate a treaty of peace with the Allies. The French occupation of the Ruhr continued during April without there being any spectacular develop-ments. Of course there was surliness on the part of the Germans. In the meanwhile the statesmen on both sides were intimating what they might give and what they might take, sounding the sentiment of their respective populaces. The British Government found that its revenue for the last fiscal year has been greatly in excess of expenses. The surplus was applied to reduction of the debt. A consequence of this development has been a reduction in British taxes for the ensuing year, which has naturally created a much better feeling in Great Britain. On the other hand the unemployment situation in Great Britain caused increasing alarm. At the begin-ning of April about 1,500,000 men were out of work and the thought was developing that this might be not merely a temporary emergency, but a long continuing condition. The uneasiness of the workers themselves began to be exhibited in increasing strikes and threats of strikes. There were important domestic events during April. The six miners who were on trial in Illinois for the Herrin massacre were acquitted, following which the State dropped further prosecutions on the ground that Williamson County is so thoroughly under labor domina-tion that justice could not be had there. The Supreme Court of the United States on Apr. 10 handed down a decision that an act of Congress fixing minimum wages for women in the District of Columbia was unconstitu-tional, being interference with the freedom of contract included within the guarantees of the fifth amendment. Advances of wages became more general during April. The leading event under this head was the action of the United Steel Corporation putting into effect an.11 per cent. increase in the wages of common labor on Apr. 16, by virtue of which the rate per hour was raised from 36 c. to 40 c. This was dictated by competitive conditions, the labor difficulties of the steel industry being due less to a scarcity of men than their disinclination to take jobs in that industry while the building and other industries were paying as high as 60 c. per hour for similar work.

Jan 5, 1923

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By Fred J. Wright

Originally, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are. now literally the heart of the mining machine. During world war NO. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the Same time will lower costs for the oil by extending its life. Rulk purchases of oil should be limited to small sealed containers provided with a Proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives1 will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1947

By Fred J. Wright

ORIGINALLY, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are now literally the heart of the mining machine. During World War No. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Contamination of Oil Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the, proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the same time will lower costs for the oil by extending its life. Bulk purchases of oil should be limited to small sealed containers provided with a proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives, will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1946

By Fred J. Wright

Originally, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are. now literally the heart of the mining machine. During world war NO. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the Same time will lower costs for the oil by extending its life. Rulk purchases of oil should be limited to small sealed containers provided with a Proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives1 will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1947

By R. V. Smith

The theoretical background for calculating friction factors for flow in gas wells by two methods is presented. The first method, requiring pressures, temperatures and specific volumes of the flowing fluids at various depths in the well bore, shows how the mechanical-energy-balance equation for vertical flow may be graphically integrated over the actual path of the expansion of the fluid in the well. Thus, assumptions regarding the effective temperature and effective compressibility of the fluid in the well are avoided. The second method presents an equation derived on a basis of the assumptions that both the temperature and the compressibility are fixed at constant effective values throughout the flowing column of gas. The second method provides a convenient and practical means of calculating friction factors for gas wells and lends itself readily to the problem of calculating subsurface pressures in a flowing gas well. The application of both methods to actual test data taken on a flowing gas well is illustrated in the paper. INTRODUCTION As friction factors for the producing strings of flowing gas wells cannot be measured directly and must be calculated from flow-test data, study of the methods of arriving at friction factors is a necessary adjunct to understanding the characteristics of flow in gas wells. There are two methods of calculating friction factors for gas wells; they differ from one another mainly in the treatment of the path of expansion of the fluid in the well. In the flowing well, the energy consumed in lifting the fluid from the bottom to the top of the well, overcoming the friction between the moving fluid and the pipe walls, and increasing the velocity of the fluid as it flows up the producing string is supplied by expansion of the flowing fluid. The available energy is determined by the expansion of the fluid that follows a path determined by conditions of temperature, compressibility and phase changes of the fluid during the expansion. A means of evaluating the available energy in a flowing gas well and determining the proportion of the available energy used in lifting the gas, overcoming friction, and increasing the velocity of flow is developed in this report. Knowing how much energy is consumed in overcoming friction makes it possible to calculate friction factors for given flow rates in given sizes of pipes in wells. Friction coefficients, as used in this report, are dimension- less proportionality multipliers used in the flow equations to satisfy the equality between the terms of the equation. The square root of the reciprocal of the friction coefficient is termed the friction factor. It has been known for many years that friction factors may be computed directly from mathematical formulas based on certain assumptions regarding the temperature and compressibility of the moving fluid in a well. A general equation is presented in this report without assumptions for vertical flow of fluids and a conventional-type equation is derived on the basis of assumptions that fix the temperature and compressibility at constant values. Accurate pressures at the sand faces in wells are required in the method of determining the productivity of gas wells, as outlined by Rawlins and Schellhardt1 in Bureau of Mines Monograph 7. Where measurements are not made with subsurface-pressure gauge; or static gas columns are unavailable, flowing pressures customarily are calculated at the sand face in the well by the use of the well-known Weymouth formula1. Natural gas engineers have realized that errors introduced by the use of friction factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; they also know that such factors are important considerations in testing large-capacity gas wells. Accordingly. present research on the productivity of gas wells at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla., is being directed toward measurement of the pressure loss due to friction in flowing gas wells. It is beyond the scope of this report to show how friction factors vary with rate of flow and in pipes of different diameters, as it is intended only to develop and illustrate the use of mathematical expressions for calculating friction factors from flow-test data. The equations presented apply only to turbulent flow in circular pipes. ENERGY RELATIONS FOR FLOW OF FLUIDS2 The concept of conservation of energy is usually the basis of any study of fluid flow through vertical pipes as in gas wells, horizontal pipe lines, or orifices. In deriving equations, the following symbols are used:

Jan 1, 1950

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By M. R. Geer Olds, H. F. Yancey

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built. This rapid growth of dense-medium cleaning has been concurrent with widespread adoption of full-seam mining on one hand and a return to a more competitive market on the other. At a time when changing mining practice has provided cleaning plants with dirtier coal and changing market conditions have simultaneously demanded a cleaner product, the industry has through necessity turned to improved preparation. The inherently greater sharpness with which dense-medium processes can separate coal from impurity is thus helping to hold the line against ever-increasing mining costs and at the same time assisting materially in retaining badly needed markets. Although dense-medium cleaning unquestionably offers a distinct advantage when the washing problem is difficult, other methods can provide almost equally high efficiency when the coal is easy to wash. Moreover, fine coal cannot yet be treated by heavy medium in a proved process, although the Driessen cyclone is in the pilot-plant stage. Most of the present types of dense-medium equipment have been in use only a few years, and the dearth of information in the literature concerning their performance characteristics is entirely understandable, Nevertheless this information is necessary if the process is to be intelligently applied to individual cleaning problems. Without data on the efficiency of a process in a particular type of separation, it is difficult to assess the advantage to be expected from it. Similarly, the role of particle size in heavy-medium separation is important in some cases, yet there is little published information on this aspect. To mention only one more of the numerous points on which essential information is lacking, the bearing of medium characteristics on performance has been discussed only in qualitative terms. It was with the hope of providing information on some of these points that the Bureau of Mines built a dense-medium pilot plant for cleaning coal at its Northwest Experiment Station in Seattle in 1950. The plant has been operated continuously since that time, and over 50 runs have been made on 7 coals exhibiting a wide range of washability characteristics. An idea of the magnitude of this work will be gained from the fact that examination of the plant products has involved some 600 float-and-sink separations and about 2500 ash determinations. A laboratory pilot plant is especially well adapted to investigate many aspects of performance because close control over test conditions can be exercised and because a large number of tests can be made rapidly. On the other hand, factors such as consumption of medium and other cost items can be investigated satisfactorily only in a commercial plant. Actually, the two forms of investigation should be complementary, with the laboratory work pointing the way for confirming tests in commercial units. Pilot Plant The dense-medium pilot plant employed for this work comprises a 24x30-in. drum-type separating vessel, a 12-in. densifier, a 12-in. magnetic separator, a 26-in. x 9-ft vibrating screen, and the necessary pumps and conveyors for handling materials. Arrangement of these units corresponds with the flowsheet used in most commercial plants, except that a thickener is not provided for the feed to the magnetic separator. Coal and refuse discharge from the separating drum to the vibrator, which is divided longitudinally down the center. Medium draining through the first 3 ft of the screen is recirculated directly to the drum. Sprays on the middle 3 ft of the screen rinse medium from the products, and the last 3-ft section is for dewatering. Dilute medium from the rinsing and dewatering sections is pumped to the magnetic separator, where magnetic solids are recovered. These are pumped to the densifier, from which they return to the medium-drainage sump by gravity through a demagnetizing coil. The drum-type separating vessel is a scale model of a commercial unit. Feed enters axially at one end of the drum just below the surface of the bath, and float material overflows through a circular opening at the other end. Particles sinking to the bottom of the bath are picked up by lifting flights bolted to the inner wall of the drum, elevated out of the bath, and sluiced to the vibrating screen. Baffles suspended in the bath prevent float material from entering the sink-lifting flights. About 8 gpm of medium is used to sluice the feed into the drum. An additional 15 to 24 gpm, depending upon operating conditions, is added through two pipes dipping into the bath behind the baffle on the side where the sink-lifting flights enter the bath. The bath available for separation is 2 ft long and 13 in. wide, giving an area of 2.08 sq ft. Depth of bath from the surface to the top of the sink-lifting flights, measured vertically below the axis, is 6 in.

Jan 1, 1954

By Benjamin N. Webber

The peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana-caste, which is the northern. of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guay-jiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. Physiography In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low- lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. History and Production The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1949

By F. E. Griffith

Several disastrous and a great number of near-disastrous mine fires have been started by igniting the combustible conductor insulation and outer covering of trailing cables. Those who have had experience in fighting such fires know that they are extremely difficult to combat and extinguish owing to the irritating and noxious gases, fumes and vapors evolved from evaporation, distillation and combustion of the sundry compounds used in the construction of cables. When electric-motor-driven coal-cutting machines were first introduced in coal mines, the electricity was transmitted to the apparatus by two single-conductor trailing cables. Later, two-conductor parallel and concentric types were developed. These early cables were made with the materials available at that time with relatively little thought given to using new materials or utilizing the old to the best advantage. The copper conductors were stranded to give flexibility, but there were too few strands and the method of laying them was such that they did not endure well the stresses of twisting and pulling, to which trailing cables used in mines are usually subjected. The rubber insulating compounds used were not satisfactory in resisting water, high temperature, and the crushing stresses encountered in mine service. The outer coverings were cotton or jute braids saturated with tars or asphalts having relatively no abrasive resistance. In fact, the only consideration given to trailing cable design because of its extremely short life, was to construct it at the lowest possible cost. With increased electrification and mechanization, more serious problems were encountered. Cables used in mines were exposed to more severe conditions than in any other industry. The excessive overload currents, poor heat dissipation, severe abrasion, crushing loads from falling material, runovers, and any of the other things that tend to destroy cable, called for vast improvement in trailing cable design for mine use. About 1918, one manufacturer who recognized the need for improving the toughness of cables in order to obtain greater safety and longer life, developed a special rope-stranded conductor, a superior rubber insulation compound and a tough rubber sheath or jacket compound. As a result of this type of construction, broken conductor strands were practically eliminated, the insulating material withstood high temperature without undue disintegration, and the jacket, similar to that used for automobile tire tread, had high abrasion resistance, high tear resistance, and was waterproof. While the initial cost of these cables was higher than the jute-filled braided types, this disadvantage was more than offset by increased safety and longer service. Cables with these improved characteristics were first installed in mines in 1920. Since 1930, the use of braided trailing cables in coal mines has been almost completely supplanted by the more superior types, employing high-grade rubber compounds for insulation and sheath. The next steps taken to improve the

Jan 1, 1949

By Paul F. Fulton, Robert K. Estes

INTRODUCTION Relative permeabilities are factual data necessary to any prediction of reservoir production behavior. One important problem in determining relative permeabilities of porous media to gas is the effect of gas slippage on these determinations. Since certain aspects of the slippage phenomenon still remain unknown, this study is particularly concerned with that problem. The validity of the theory of gas slippage as it is applied to the flow of gas through porous media has been well established. 1,2,3 Therefore, in determining the permeabilities of porous media to gas by ordinary laboratory procedure, i.e., at atmospheric pressure, the slippage correction should be considered. Rose3 performed experiments on gas relative permeabilities which indicated that the effect of gas slippage on the measured effective gas permeabilities at various liquid saturations decreased with an increase in liquid saturation. Following Rose, it was substantiated experimentally' that the effective gas permeabilities at the various liquid saturations extrapolated to infinite mean pressure were the same as the non-wetting liquid permeabilities at the same saturations. This same paper also presented data which showed that the magnitude of the slippage between those values of gas effective permeability determined at atmospheric pressure and those found by extrapolation to infinite mean pressure decreased with an increase in liquid saturation. However, these experiments were not performed at liquid saturations above 30 per cent. Therefore, the purpose of this experimental work was to determine the effect of gas slippage on permeability measurements at liquid saturations in excesh of 30 per cent. APPARATUS Five core samples were used In this work: two synthetic Alundum samples (A-1, and A-2). a Nichols Buff sandstone sample (NB-13), and two samples from producing formations, a Soso sandstone (S-1), and a vugu-lar dolomitic limestone (R-7). The core samples ranged in permeability from 32 to 663 md. These cores were chosen because they represented a fairly wide range of permeabilities and probably a considerable difference in pore size and pore size distribution. Fig. 1 is a schematic diagram of the apparatus which consists of an air dehydration filter A, two Moore null-matic sub-pressure regulators B and C, the differential oil manometer D, the core holder E, the flowmeter F, the soap reservoir G, and a mercury manometer H measuring the downstream pressure. The interesting features of the apparatus are the two Moore vacuum-pressure regulators. The regulators permit the rapid establishment and easy control during flow at sub-atmospheric pressures of both the differential and downstream pressures, and prevent the surging action of the vacuum pump from disturbing the system during flow. Provided there are no leaks in the system, these regulators will maintain without measurable change selected downstream and differential pressure. Specifically, regulator B controls the downstream pressure and regulator C controls the differential pressure. In opera-

Jan 1, 1957

THE Institute assembled in the Court-House, on Tuesday evening, May 22d, and was called to order by Vice-President E. B. Coxe. After announcement by the Local Committee of the programme for excursions, the Secretary read the following annual report of the Council The Council, in presenting to the Institute its annual report, has to record a most eventful year in the history of the Institute. Three meetings, as usual, have been held, two in Philadelphia and one in New York. At the Philadelphia meetings in June and October, there were present many distinguished foreign engineers, some of whom contributed communications to the Institute, and took part in its discussions. Sixty-seven papers have, in all, been presented to the Institute, which will be published in the fifth volume of Transactions. There has been an accession to the membership of 1 honorary member, 11 foreign members, and 162 members and associates; -8 have resigned, 6 have died, and 30 have been dropped from the roll, after due notification, for non-payment of dues. The membership now comprises 5 honorary members, 60 foreign members, and 644 members and associates, in all 699. As worthy of especial mention in the work of the year are the Discussions on Technical Education in connection with the American Society of Civil Engineers, and the report of the-International Committee appointed by the Institute to consider the nomenclature of iron and steel. The Discussions on Technical Education have been published in a separate volume, and comprise a valuable and suggestive collection of the views of practical engineers and educators. The report of the International Committee, composed of Messrs. Akerman, of Sweden; Bell, of England; Tunner, of Austria; Gruner, of France; Wedding, of Prussia; and Holley and Egleston, of the United States, has received the careful attention of engineers and metallurgists of all countries, and has met . with very general acceptance. Of the work of the Centennial Committee in Philadelphia the members are generally familiar, from personal experience, and from the detailed report of the committee at the last meeting of the Institute. But the record of the service rendered by this committee would he incomplete without mention of the numerous letters of thanks and formal expressions of obligations received by the Institute from individuals, societies, and governments abroad. The wise and generous spirit in which the work of the committee was planned, and the laborious and self-sacrificing manner in which it was carried out, call for emphatic expressions of thanks from the Institute. The gifts of Centennial exhibits to the Institute, largely as testimonials for services rendered, has necessitated the appointment of a Museum Committee for

Jan 1, 1878

ANYONE who wishes to make the patterns for statues in order to cast them later in bronze, even though he himself is the artificer who made them, must take many things into consideration: first, whether they are large or small, and whether they are wholly round or only in part; then of what material they are made, for the way that can be followed if they are of wax cannot be used if they are of clay, wood, marble, or even of plaster; likewise he must consider whether or not it has irons inside to support it. There is also a great difference in facility if the support is placed more in. one way than in another. Great consideration should be given to whether it is to be made hollow or solid. If you have not been the workman yourself, you must at least have been an active helper in this and in every other part in order to be able to observe everything without a fault. For if they are large it is necessary to make their moulds in pieces, with marks and measurements so that you can replace them-at will exactly in the same order and in the same places after they have been taken out. But if you are the artificer [as well as sculptor] the process is made easier. Taking the ordinary way and, over an iron, make out of well beaten moulding clay, compounded with cloth clippings a core exactly as the statue is to be or however large you wish the hollow to be. Dry and bake it. On top of this work the wax, thickening it all over as much as you wish the bronze to be and finish it completely, remembering to arrange that the base may come out solid with bronze so as to support the whole work. Then take some rods of hammered bronze one dito thick and one palmo long. Pass these throughs the thickness of the wax and fasten them in several places in the core of clay that you made. [81] Do it so that they, project out of the wax a good three or four dita. These are, put in so that when the wax is removed the core is held in the middle of the mould that forms the outer part, and this outer part is held by the inner part, namely the core, so that the mould may not move in any part from its place even when it is handled. This done, take some of that clay made with well-prepared cloth clippings as I taught you, and mix with it if you wish some wash ashes or

Jan 1, 1942

By G. D. Van Arsdale

THE paper of Mr. Posnjak presents a laboratory confirmation of the well known facts that air ox-idation of pure solutions of ferrous sulfate is slow and difficult and that, like many other similar reactions, the speed, may be greatly accelerated by the presence of other substances, often in very small amounts, the effect of the presence of copper being determined ex-perimentally in this case. However, it should not be. overlooked that copper is always present in heap leach-ing solutions in amounts equal to or greater than those in the experiments described; therefore the paper may be considered as an explanation of present results rather than a possible improve-ment to be added to present practice. It is not practicable and it does not pay to precipitate copper by ce-mentation below a point about 5 lb. per 1000 gal., equivalent to about 0.0005 mol. Cu. per liter, compar-ing with the approxi-mately 0.0009 mol. per liter of curve 2 in the diagrams given of course, also, in the heaps local concentrations are usually very much higher than this, which is also true of the effluent li-quors, so that I feel that it is safe to say that copper is already present in amount sufficient to realize, as large an accelerating effect as is practicable. Too much im-provement or refinement cannot be expected in a method of this kind, due to commercial limitations. It should be remembered that chemically and physically there is no sharp dividing line between leaching in place, heap leaching, and the usual tank leaching practice, practi-cally the same reagents being used in all three. From the viewpoint of extractions, etc., it is not common sense to apply leaching in place to an orebody carrying enough copper to pay for mining; and the same is true of heap leaching, for an ore carrying enough to pay for the crushing, handling, etc., of ordinary leaching. That is to say, leaching in place should properly be consid-ered only for an ore too low-grade to pay for mining, and heap leaching for the next higher grade, still how-ever too low-grade to pay for crushing and other re-finements. There is no advantage in leaching without mining or in heap leaching except lower cost of in-stallation and handling; on the other hand there are very distinct disadvantages which are inherent and which should prohibit their use except where necessity requires. The object of metallurgy is to make money out of the handling of ore, and it is purely a question of money as to how far we can go in "improving" or

Jan 7, 1927