Search Documents

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By H. H

This paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. Characteristics of the Ore The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾, mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3Al2 (SiO4)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to I2 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crys- tals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3-07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive- Former Operations Mining operations have been carried on for 60 years. Until 1923, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By H. H

This paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. Characteristics of the Ore The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾, mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3Al2 (SiO4)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to I2 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crys- tals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3-07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive- Former Operations Mining operations have been carried on for 60 years. Until 1923, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By N. Tiner

In an article on magnesium and its alloys, Gann and Winston! stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 675°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I). This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of, these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing 0.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C. and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. Experimental Method The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By G. Sachs, G. Espey

IT is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.1-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.1-6, It has also been observed that higher stresses are set up by the use of wide-angle dies than by the use of acute dies.2 The actual stress distribution in drawn .tubing has been investigated by a few workers,7-9 but has not been related to the conditions of the drawing process: Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal.1-10 MATERIALS AND PREPARATION The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.‡ This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2 -in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during sinking, as previously observed 4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation method1,11 of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring on splitting. For the determination of the complete stress

Jan 1, 1941

By Robert I. Jaffee, Bruce W. Gonser, Eugene M. Smith

There has been little investigation of the gold-germanium binary alloys. Haughtonl does not mention any work on the system. In a review article commemorating the fiftieth anniversary of the discovery of germanium, E. Einecke2 mentioned a gold-germanium eutectic at 24 atomic per cent Ge (10.4 weight per cent) melting at 359°C., but did not give the source of his information. From measurements of electrical conductivity, J. 0. Linde3 estimated that at least 0.6 weight per cent germanium is soluble in gold. The recent availability of germanium in this country in commercial quantities has led to interest in its properties and its alloys. This study is part of a program of investigation on germanium alloys; work on ternary alloys involving germanium and gold will be reported later. In this investigation, the composition and melting point of the Au-Ge eutectic reported by Einecke has been found to be substantially correct. Eutectic composition has been placed at I2.0 per cent germanium, however. An alloy of 10.4 per cent Ge, Einecke's value, was found to have a few gold dendrites in it. The cutectic temperature has been determined as 356.0 6 ± 0.5°C., slightly less than the temperature of 359°C. reported by Einecke. The liquidus curves and the solid solubility of ger- manium in gold have been determined, and are shown in Fig. I. Materials and Alloying The germanium used in this investigation was prepared by the Eagle-Picher Lead Co. from pure germanium oxide, by reduction in clay crucibles with sodium cyanide. The regulus is quite pure, assaying over 99.9 per cent Ge. High-purity gold obtained from Handy and Harmon was used. Alloying was carried out in graphite crucibles in an atmosphere of purified hydrogen. The temperature was brought up to 1050" to iioo°C., and the metal was allowed to freeze in the crucible. Prepared in this way, the gold dendrites in hypoeutectic alloys were somewhat segregated at the bottom and sides of the ingot, and on the hyper-eutectic side the lighter primary germanium tended to gather at the top. Most of the alloys were made from virgin metal. Low-germanium heats were made by alloying pure gold with the eutectic. Melting losses were consistently a few milligrams or less, and the composition could safely be taken from the intended analysis. The 30 per cent and 50 per cent germanium heats for thermal analysis were made in part from remelted higher germanium heats, and they may be OR composition as much as one per cent. Because of the high cost of materials, the weight of heats for thermal analysis were 15 to 20 grams and heats for metallo-graphic, X-ray, and hardness specimens were 2 to 4 grams.

Jan 1, 1945

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors' reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

By C. L. Magee, H. W. Paxton

PREVIOUS workersl'% ave found that as-quenched ferrous martensites can be plastically deformed at low stresses. They have also found that the stress to obtain small strains can be significantly increased by aging at temperatures up to 150°C. This behavior has been interpreted in two ways: 1) that the deformation at low applied stress is due to internal stresses and thus the aging phenomenon is due to relaxation of the internal stresses;' 2) that the microdeformation arises through the motion of unpinned dislocations and the aging process is the diffusion of carbon to the dislocations to pin them.293 In a recent paper,4 we have shown that under certain conditions the dominant microdeformation mechanism of as-quenched Fe-31Ni marten-site-austenite aggregates is the transformation of retained austenite. Our results on resistance changes during deformation and temperature dependence of the deformation also established that, at temperatures above 300° K, the microdeformation was not due to this transformation. The purpose of this note is to report results of experiments which indicate that explanation 1 is appropriate for this deformation. All results presented here are from conditions where transformation does not make a measurable contribution to the microplastic deformation, in Fe-31Ni-0.002C, or in Fe-29Ni-0.02C-0.25Ti. The experimental techniques that were used for measurement of the plastic deformation are described4 and analyzed5 elsewhere. Fig. 1 shows the microplastic response of 100 pct austenite at 300" and 350° K. The microplastic response of an austenite-martensite aggregate is also given in Fig. 1 and it is seen that, after formation of martensite, the initial plastic deformation occurs at lower stresses. Thus, the softness is not entirely due to retained austenite—the quenched structure can be deformed at lower stresses despite the fact that the macroscopic strength is significantly higher. A result which allows a distinction to be drawn between the alternative explanations for this behavior is derived from aging experiments on the low-carbon alloy containing titanium. We have previously shown4 that the presence of titanium in this alloy reduced the free carbon to a sufficiently low level that thermal stabilization of the austenite-martensite transformation was not detected. Despite this, Fig. 2 shows that the microplastic response is decreased by aging treatments. A similar aging effect in Fe-ZONi, with some titanium, has previously been reported by . Thus, carbon is not necessary for the aging process and explanation 2 is at best incomplete. Since internal stress relief can occur independently of carbon (any temperature dependence of the flow stress can result in decreased internal

Jan 1, 1969

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

One of the best known of the early mining districts of Nevada was that at Eureka, where gold was first produced in 1864. While the most productive period for the district was during the early 1900s, production was maintained until World War II. During this time it is said that the Eureka district produced as much as $200 million from over 3,200 km (2,000 miles) of tunnels and workings. The Windfall Mine was discovered in 1902; and a 100 ton cyanide plant was operated there during the periods 1907 to 1912 and 1932 to 1940. Since 1974, however, Windfall Venture has been operating a unique heap leaching facility on the site of the old Windfall Mine. Gold at the Windfall occurs primarily in the Cambrian Hamburg dolomite which has been "sanded" and in which the original cementing material has been destroyed. The gold is micron sized and is accompanied by anomalous amounts of arsenic and mercury; however, the ore is low in base metals which distinguishes it from the typical Eureka district ores. Mining the ore causes it to break down into very fine sizes, approximately 50% minus 150 microns (100 mesh). Conventional heap leaching by spraying proved to be impossible; and extensive test work on alternate methods, aided by the United States Bureau of Mines, was conducted using 9 m (30 ft) high columns and then large tonnage heaps. The leaching procedure adopted was to build 10.6 m (35 ft) high heaps on a 50 mm (2 in.) asphalt pad covered with a layer of gravel for drainage assisted by perforated pipe drains and gravel-packed sumps. A berm is constructed around the top of each pad and cyanide solution is allowed to “pond” on top of the heap. The resulting percolation is at the rate of 24 liters per sq m per hr (0.6 gal per sq ft per hr), a figure about 2.4 times the average used in other heap leaching operations. The dolomite furnishes its own protective alkalinity and no lime or caustic is used in the solution which contains 0.4 kg per mt (0.8 lb per st) of NaCN. Pregnant solution from the heaps averages about 0.7 g Au per mt (0.02 oz per st) with a cyanide content of about 0. 2 kg per mt (0.4 lb per st) and a pH of plus 9. Addition of NaCN brings the pH of the leach solution up to 11 to 12. Carbon adsorption of the gold was originally done in six enclosed columns mounted in a trailer but five conventional columns have been substituted as the size of the operations has increased. Carbon stripping is with hot caustic, cyanide and 10% ethanol solution. The

Jan 1, 1981

By J. B. Cohen, M. B. Beaver, R. J. Black

RECENT investigations have shown that face-centered cubic metals may deform by twinning. Blewitt, et al' found that at 4.2"K the mode of def~rmation of single crystals of copper changed at large strains and markings formed on (111) planes. Later they- emonstrated by X-ray diffraction and metallography that the markings were twins and showed that favorably oriented single crystals of copper deformed by twinning at 78°K. They also observed twinning in silver and gold deformed at 4.2 and 78°K. Wagner3 obtained evidence for twinning from the peak shape of diffraction lines of silver cold-worked at 78°K, but twins small enough to cause such effects are not likely to be detected metal-lographically. In the work reported here lamellar structures were observed in deformed silver-gold alloys. They appeared to be mechanical twins, but metallography could not establish this conclusively. Their tendency to form depended on strain rate, temperature and composition. Specimens of silver-gold alloys (0 to 83 wt pct Au) were deformed plastically. One set was worked by hammering under liquid nitrogen, at room temperature and at intermediate temperatures. Another set was compressed slowly in liquid nitrogen to the same reductions as those produced by hammering. Tensile specimens (0.015 x 0.120 x 1.5 in.) of various compositions and approximately equal grain size (0.011 to 0.016 cm) were tested at -195°C and at room temperature. In microsections of all specimens deformed by hammering at —195°C thin lamellae appeared, Fig. 1. They were aligned in definite directions in each grain. In some grains they had two orientations. Where lamellae intersected, a displacement was apparent. Near the center of the left margin of Fig. 1 shear has taken place beyond the fully developed intersecting lamella. Many lamellae resembled Neumann bands in alpha iron. They were parallel to one side of triangular etch pits in the matrix (as in Figs. 1 and 2). The individual lamellae were narrow and had little substructure. This suggested that they did not result from concentrated local slip. The shape of etch pits within the lamellae differed from that of pits in the matrix, as can be seen in Fig. 2; this indicated a difference in orientation. Specimens slowly deformed at —195°C contained regions in which the lamellae were clustered. In these specimens some lamellae were bent and presumably had formed before the termination of the deformation. Structures of greater width than the lamellae were also seen.4 More lamellar structures formed on impact than during slow compression to a given reduction. This was true of all compositions. The structures became less abundant with increasing temperature of deformation. None was observed after extension to fracture at room temperature, but they could be pro-

Jan 1, 1959

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10' per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

By J. T. Norton, A. L. Mowry

The monocarbides of the A subgroup elements in the fourth and fifth group of the periodic table in addition to being hard and refractory are of special interest in that they are isomorphous in crystalline structure. They are cubic with a sodium chloride type structure in which the metal atoms are essentially close packed in a face-centered cubic arrangement with the carbon atoms placed in the interstices between. Interstitial structures of this close packed type were first investigated systematically by Egg1 and he gave the rule for their formation, stating that the radius ratio of the nonmetal to the metal atom should not exceed the value of 0.59. The carbides of interest are those of titanium and zirconium of the fourth group and vanadium, columbium and tantalum of the fifth group. Table 1 shows the radius ratio using the Goldschmidt radii for 12 coordination for the metal atoms and the diamond radius for the carbon atom. It will be noted that while there is considerable variation in the size of the metal atom, in all cases the ratio is smaller than the limit of 0.59 placed by Hägg. It has been known for some time that these cubic carbides are soluble in one another, at least to some extent or, in other words, the metal atoms can be replaced, one by another without destroying the stability of the structure. Since the stability of these close packed interstitial substances appears to depend more upon geometry than upon the exact chemical nature of the atoms involved, it is of interest to examine the possibilities of replacement in these carbides in some detail. Hume-Rothery2 has pointed out the importance of the difference in size of solute and solvent atom as a factor in limiting the solubility in simple binary solid solutions. Largely on an empirical basis, he states that if the difference in size between solvent and solute atom is more than 14-15 pct of the solvent atom, the range of solubility is very restricted. The atom size was based on the distance of closest approach in the elements involved. While there is some question as to how one should calculate the size of the metal atom in the carbide structures, reference to Table 1 will show that zirconium is the largest and vanadium the smallest of the group and that the difference is about 15 pct. The Ti-Zr difference is about 9 pct and the others are smaller. Thus one would predict that if the size factor controls the solubility, all of the pairs except VC-ZrC would have wide or complete solubility whereas this latter pair is on the border line and might have restricted solubility. The purpose of the present investi- gation was to examine the solubility of the several pairs of carbides by heating them together until equilibrium was established and then examining the product by X rays. Previous Work Agte3 and his associates prepared various transition metal carbides and determined the melting points of binary mixtures. He concluded from the shapes of the melting point curves that there was extensive solubility in the case of the cubic carbides. Umanskii and his colleagues made an investigation of a number of pairs of the cubic carbides, using X rays and plotted lattice parameter vs. composition curves for the systems TaC-Tic, CbC-Tic, TaC-ZrC and CbC-ZrC. All pairs showed a continuous series of solid solutions. The first two pairs gave a linear relation while the latter two showed a negative deviation from Vegard's law. Kiefer and Nowotny, in a paper which became available after the present work was well advanced, investigated the binary pairs of the five cubic carbides by means of X rays. Relatively few points were obtained and results indicated that in some cases, at least, equilibrium was not reached at the temperatures used. The results indicated that solubility in the VC-ZrC system was not complete. All of the results of previous investigations indicated the desirability of a more detailed study. Materials The raw materials used were mono-carbides of titanium, zirconium, vanadium, columbium and tantalum and were the purest which could readily be obtained commercially. Spectrographic qualitative analysis showed that the CbC and TaC contained less than 1 pct

Jan 1, 1950

James Gayley, Braddock, Pa. (communication to the Secretary) : Mr. Potter has made reference to our practice at the Edgar Thomson works in the direction of increasing the life of the lining, and mentions the product of one of our furnaces as having reached a total of 370,000 tons. It may be interesting to know that this furnace has been put out of blast with a record of 452,685 tons, after a run of three years and nine months. A companion-furnace to this will produce, hefore the present year is ended, half a million tons. As Mr. Potter has quite correctly designated this as " the newest problem in furnace-practice," a description of the construction of this furnace lining may be Welcome to members. The bricks used in the lining are 9 and 134 inches long, with the requisite quantity of straight and key-shapes to turn the circle. There bricks are well suited for enclosing the numerous bosh-plates used for cooling. The bosh-plates (the efficient fortress of the lining) extend from the top of the tuyere arch to the mantel, and are inserted in rows, 18 inches to 2 feet apart. These form a perfect defence against encroachment on the bosh-lining, and leave the bosh at the end of the blast of the same thickness as at the beginning. The protection afforded by these bosh plates is the principal cause of the increased duration of the furnace-lining. But it must be noted that the shape and material of the plate are essential elements. The most serviceable plate is that made of bronze or copper. We have tried every form of iron plates without obtaining satisfactory results. These were replaced with bronze plates, built into the lining, which gave excellent results so long as they did not leak; but when this occurred, as it did in time, the water was shut off, and, since the plates could only be removed with difficulty, they were allowed to burn off. This permitted encroachment on the bosh-walls, which thus became enlarged beyond the limit required for economical practice. With the introduction of the removable plate, made tapering on the sides, with plain surfaced top and bottom, these troubles have

Jan 1, 1895

By S. S. Cole, H. Sigurdson

The melting points of mixtures of titanium dioxide and other titanates have been reported to a limited extent as binary systems and some results have been reported in conjunction with silicon dioxide. The limited data indicated that a low melting zone might exist in a ternary or quarternary system of CaO-MgO-TiO2-Al2O3, since the eutectics reported in the binary systems of MgO.TiO2-TiO2, Al2O3TiO2-TiO2 and CaO.TiO2-TiO2 were of about equivalent composition of TiO2. The importance of a low melting region with a high titanium oxide value in the developing of high titanium slags is fully appreciated by metallurgists. A comprehensive study was undertaken to establish basic information on low melting titanate mixtures. Compounds in the System CaO-MgO-TiO2 -Al2O3 Preparation of the titanates of CaO, MgO and Al2O3 confirmed reported data that the following compounds could be formed under oxidizing conditions in solid state reactions: CaO.TiO2, 2MgO.TiO2, MgO.TiO2, MgO-2TiO2 and Al2O3.TiO2. Under oxidizing conditions it was not possible to react MgO with TiO2 in mol ratios higher than 1:2 without having unreacted TiO2 in the product, nor was it possible to form calcium or aluminum titanates with a higher mol ratio of CaO and A12O3 to TiO2 than 1:1. By fusing mixtures of Al2O3-TiO2 and MgO-2TiO2 together a series of solid solution products were obtained, which showed an MgO-2TiO2 X ray diffraction pattern shifted to smaller inter-planar spacings. Range of Investigation Data in the literature1 indicated that these titanates had melting points which ranged from 1645 to 1860°C. Since the purpose of the study was primarily to provide useful data for smelting titaniferous ores, the work was restricted to the zone of the system which would include the crystalline phases present in the slags. The explored limits were bounded by CaO.-TiO2-MgO.TiO2-TiO2in the base plane. The system was extended to a fourth component Al2O3-TiO2 since many titaniferous ores contain appreciable amounts of A12O3. In the quarternary system CaO-TiO2-MgOTiO2-TiO2-Al2O3TiO2, a tetrahedron was used to represent graphically the components, with one component at each point of the tetrahedron. In the base plane, mixtures were pre- pared to represent fairly uniform changes of composition over the desired range expressed on a mol percent basis. Al2O3-TiO2 was brought into the system in increments of 10 mol pct up to 40 pct. Mixtures were then made up for each of the Al2O3-TiO2 planes. The ranges employed were then represented by five planes cutting the tetrahedron at 10 mol pct Al2O3-TiO2 intervals. Choice of Equipment Although it was necessary for all smelting work to be done in a strongly reducing atmosphere, it was decided that all melting point determinations should be done under oxidizing conditions. This decision was prompted by the fact that TiO2 reduced to lower oxides in a reducing atmosphere with consequent changes in melting points. The use of a micropyrometer and a platinum strip furnace for work of this type is adequately described in the literature.2 With modifications, equipment was selected which provided a fairly rapid method of determining melting points of refractory oxides. The final assembly, which was used, consisted of a platinum strip furnace and a Leeds and Northrup disappearing filament optical pyrometer attached to a special telescope which magnified the sample about 20 diam. The furnace assembly consisted of a platinum strip 0.005 X 0.3 X 2.2 in. mounted on brass posts on a refractory base. This was enclosed in a black steel shell which had a 2-in. opening at the top for purposes of sighting the telescope. The platinum strip was in series with two 0.04 ohm nichrome resistors connected to the secondary of a 2 kw transformer which supplied 17 volts. The current to the primary was varied

Jan 1, 1950

By G. L. Simard, D. J. Salley, J. Chupak

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By J. Chupak, D. J. Salley, G. L. Simard

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951