Search Documents

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By V. J. Berry, J. D. Pendergrass

Well pressure transient tests provide a means for directly obtaining information about formation pressure and reservoir flow capacity. Such tests have also been proposed for determining presence and location of faults or other reservoir closures and for measuring oil in place. For mathematical convenience, most theoretical studies have considered the reservoirs to be homogeneous. Definitive information is not yet available to show whether the actual presence of nonuniformities will make pressure transient behavior different from that of a uniform reservoir. The conclusions reached from actual transient tests are questionable, therefore, insofar as they rely on the original assumption of homogeneity. One type of nonuniformity commonly assumed to exist is that of stratification. In most reservoirs the strata are thought to be in vertical communication. Equations for the transient flow of a single-phase, compressible fluid in a one-well, bounded, circular reservoir have been solved for several situations involving crossflow between multiple strata of various thicknesses and permeabilities. The results show that except for the very early flow period, which usually is too short to be analyzed, the transient performance observed at the well is substantially identical with that of a homogeneous reservoir having the same dimensions and having the same steady-state flow capacity. Thus, stratification does not adversely affect interpretation of well transient tests. This conclusion holds for all commonly encountered combinations of reservoir thickness and external radius. Deviations are observed for unusually thick reservoirs whose outer radii are relatively small. The results of these studies also show that the presence and the amount of stratification cannot be simply diagnosed from reservoir pressure transient data when there is crossflow between strata. INTRODUCTION The last decade has brought wide acceptance of the transient well pressure test for determining reservoir parameters. Following the original work of Hurst and van Everdingen,1 the mathematical theory was thoroughly explored. Numerous authors have suggested how to determine static reservoir pressure, permeability-thickness product, original oil in place and reservoir limits for different reservoir geometry. The same mathematical techniques have been used to predict the transient performance of a reservoir over a long period of time. Most of the theoretical work has been for homogeneous, isotropic systems. Some results have also been presented for a homogeneous, anisotropic reservoir.2 Petroleum reservoirs are not homogeneous. The deposition process seems to favor creation of a stratified formation. This concept is sufficiently well accepted so that the most natural extension of the transient flow theory beyond the homogeneous case is to a stratified formation. Results for a stratified reservoir with no vertical communication between layers can be obtained from the results for a homogeneous reservoir. Lefkovitz, et a1,3 have given a thorough treatment of the two-layer case. Two recent papers4,5 have treated the case of a two-layered reservoir with vertical communication or crossflow, between layers. Russell and Prats4 find that, after a relatively short time, the two-layered reservoir with crossflow exhibits a simple exponential pressure decline. From this time forward, the behavior is not distinguishable from the behavior of a homogeneous reservoir having the same steady-state flow capacity. The results of Katz and Tek 5 are equivalent. Russell and Prats4 also speculate that a multi-layered reservoir with crossflow will behave as a homogeneous system after long enough production time "... providing the contrast in kh between layers is not too great". They also suggest that, at intermediate times, "... the relative positions of the layers with respect to each other will have a great influence on the production behavior and on the time at which the previously mentioned large-time approximation might be valid". Katz and Tek5 remark upon the mathematical difficulty of treating a reservoir having many layers or strata. If relative position of the layers is also

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

THERE has been considerable discussion among A metallurgists and others interested in the development of titanium alloys as to the nature of the fine line markings which appear in the microstruc-tures of unalloyed titanium and a titanium alloys. These markings have been variously called x phase, etching pits, and twins. Figs. 1 to 3 show typical examples of the line markings as they appear, respectively, in high purity iodide titanium, commercial purity titanium rod, and a high purity a alloy containing 0.2 pct N. The commercial purity titanium sample, shown in Fig. 2, contains both line markings and some spheroidal retained-ß phase. The ß phase seen in this micrograph should not be confused with the line marking, since it originates from the iron present as an impurity in the sponge metal. It will be noted that the line markings seem to have a definite orientation pattern with respect to the grains and in titanium noticeably resemble the precipitation occurring in artificially aged high purity Al-Cu alloys. This similarity led to the hypothesis that the line markings observed in titanium and a titanium alloys resulted from precipitation of some unknown phase. With the work of Hägg1 and McQuillan2 as background, there was little reason to suspect hydrogen of being responsible for the line markings. Hagg reported that up to 33 atomic pct H was soluble in a titanium, and McQuillan reported an a solubility of up to 8 atomic pct. Furthermore, McQuillan examined metallographically a 5.1 atomic pct H alloy quenched from 300°C and stated that the structure appeared to be a single-phase a solid solution. Line markings have been observed frequently and were first noted by Jaffee and Campbell3 in 1949. They did not observe them in vacuum-annealed titanium and a Ti-O and Ti-N alloys, but did observe them in Ti-H alloys containing 0.25, 0.5, and 1 atomic pct H. They stated that it was doubtful that the markings were a second phase based on hydrogen, because 1 atomic pct was far from the accepted solid solubility of hydrogen in titanium. Finlay, Resketo, and Vordahl,4 in 1950, concluded that the markings were a true second phase as a result of observations on their etching characteristics. Anderson5 Commenting on these markings in titanium was inclined to associate them with hydrogen, but was loath to call them titanium hydride, because of the reported high solubility of hydrogen. Work at Battelle Memorial Institute for the Navy Bureau of Aeronautics," done concurrently with the work described in this paper, provided information on the experiment converse to that described by Jaffee and Campbell in 1949. This work showed that the amount of line markings in unalloyed titanium could be decreased by vacuum annealing at elevated temperature. It was suggested that this was the result of removal of hydrogen; previously, the data of Jaffee and Campbell9 howed that the markings appeared when hydrogen was added. Recent work at Battelle for the Ordnance Corps, Department of the Army, which is described here, now establishes the identity of the markings as a titanium hydride phase. A sample of high-purity titanium rod 1/4 in. diam, 0.009±0.001 wt pct H (0.43 atomic pct), Fig. 1, was resistance heated in a 0.05 micron vacuum for 41/2 hr at 1500°C. During the early states of heating, the pressure increased to 150 microns, indicating that gases were being evolved. After cooling in vacuum, the iodide titanium rod was analyzed for hydrogen. Vacuum-fusion analysis showed 0.0006 ±0.0003 wt pct H (0.03 atomic pct) to be present.* Metallographic examination of the vacuum-annealed rod showed only a transformed ß structure. There was no evidence of fine line markings, Fig. 4. A section of this vacuum-annealed rod was cold rolled to 0.040 in. thick sheet and annealed for 1 hr

Jan 1, 1953

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3' phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou' zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß' was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß' phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13' was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß' which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß' on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß' phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß' and to structures, and the 4, structure can be derived from the 0' structure by a small movement of atoms mainly in the direction of the cube diagonal.4'5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p' structure and transformation from ß' to requires a large fraction of the atoms to change position. It has been shown that the ß' transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By R. W. Kraft

A comprehensive analysis of the crystallographic and metallographic structure of several Al-CuAl, lamellar eutectic grains solidified under equilibrium conditions has been performed. A consistent pattern was discovered which was interpreted in terms of a detailed atomistic model of an interface describable as: Interface II {111} AL 11 {211} <101>Al <120> ? Several arguments are presented to substantiate the theory. It is compared in detail with another interface model characteristic of the Wid-manstatten precipitate of CuAl2 in A1 at low Cu levels. In addition, a concept is proposed to help explain the structure of the compound CuAl2. It has been shown that the eutectic alloy between A1 and CuA1, can be forced to solidify as substantially parallel lamellae throughout a relatively large volume&apos; by appropriately controlling the solidification parameters of growth rate, thermal gradients, and impurity level and by causing solidification to proceed in a unidirectional fashion from one end of an ingot to the other. A typical ingot solidified in this manner shows three distinct zones along the length of the ingot, Fig. 1. At the head end is a region consisting of many different grains, some of which are elongated slightly in the direction of solidification. After a few centimeters of growth, this polygrained region gradually merges into the second zone which consists of a very few elongated coarse grains. The third zone at the tail end is a region of eutectic colonies caused by segregation of impurities. Microscopic examination of transverse and longitudinal sections of the ingots reveals that during the initial stages of growth (zone I) the lamellar structure is frequently highly distorted and twisted but that it straightens out in zone 11. This characteristic pattern suggests that nucleation of a eutectic grain begins randomly at the head end of the ingot, and that some particular orientation relationship between the phases is more favorable from an energy consideration than others for one reason or another, so that some grains grow and others which are less favorably oriented do not. The favorably oriented or "low energy" grains continue to grow until excess solute rejected at the advancing liquid-solid interface destroys the parallel lamellar structure by forming a cellular rather than a substantially planar interface. When this occurs, the parallel lamellae fan out and eutectic colonies are formed because the lamellae grow perpendicular to the local interface. Questions naturally arise as to the crystallographic nature of the "low energy" grains. What do the grains which persist into zone II have in common? Can this explain the stability of such grains during growth? To answer the first question it is necessary to determine the crystallographic orientation of the lamellae of each phase relative to one another. This has been done for Al-CuAl2 eutectic alloys by two different techniques on specimens prepared in different ways.2&apos;3 The results were different from each other and from a third orientation relationship between A1 and CuA1, reported for overaged A1-Cu alloys.4 The three orientation relationships are summarized below to illustrate their similarities and their differences. (001) ? 11 (001) A1; [l00] ? 11 [l00] Al Eutectic, Ref. 2 (001) 8 1) (001) A1; [1001 ?11 [1101 A1 Eutectic, Ref. 3 (001) ? 11 (001) A1; [l00] ? 11 [310] Al; Widmanstfitten, Ref. 4 It is not surprising that different orientation relationships were found by Ellwood and Bagley,&apos; and Takahashi3 since the solidification conditions were quite different. Nor is it surprising that Mehl, Barrett, and Rhines 4 found still another value since they were studying another type of alloy. Nevertheless, it would be expected that some logical and systematic pattern could be found if all the alloys were at equilibrium since the same two phases are

Jan 1, 1962

By Nicholas J. Palethorpe

BACKGROUND Before addressing the above topic in any detail, it is pertinent to provide some background on Australia for those people who have not been there or who have a limited knowledge of our continent. Australia is approximately the size of the continental U.S.A. (excluding Alaska) covering an area of approximately 7 million square kilometres. It has a very dry climate which has led to a concentration of people in major cities scattered around the continents perimeter. Australia&apos;s population is currently approximately 15 million. Of the work force of 6.3 million, 72% work in tertiary industries, 20.2% in manufacture, 6.5% in agriculture and 1.3% in mining. Agriculture accounts for 46% of exports, mining for 31% and manufacturing for 23,. Economic activity is based on:- Agriculture This is capital intensive and covers extensive areas and is reliant on low cost farming. A.range of foods and fibres are produced with over 70% of production being exported. Such products are of course subject to the usual vagaries of world market demand and market access, particularly in regard to the operation of trade blocks such as the E.E.C. Mineral Resources A wide range of minerals and an abundance of iron ore, coal, gas and uranium resources provide an increasing volume of exports. However, Autralia&apos;s oil resources at present only supply approximately 70% of local requirements. Industry This is diverse and encompasses the processing of agricultural products and mineral ores as well as helping to supply the consumer and capital goods needs of the whole community. However, the small scale of local markets, the geographic isolation of Australia and relatively high wage costs have limited the scale of Australia&apos;s industry. Advanced technology has overcome some of these difficulties and high tariff and import quotas protect local producers from the full force of international competition. In 1980/81 Australia&apos;s Gross Domestic Product amounted to $130 billion with approximately 24% of this being devoted to investment. In the past decade Australia has experienced inflation rates ranging from 5% to 17% and only modest real growth rates ranging from 0.4% to 5% per annum. We have also experienced, as have many other industrialised nations, continuing wage and price increases. Unemployment presently stands at 6%. MINERAL DEVELOPMENT As the above figures indicate, Australia&apos;s continuing prosperity is very dependent on the mineral and agricultrual sectors of our economy. The dependence on these sectors is highlighted by the table below which indicates our position in a global context. [Australian Production of Minerals in a World Context Western World % Total Western World Position Mineral Production 1980 1st Rutile 75 Ilmenite 31 Zircon 70 Bauxite 36 Iron Ore 11 Tungsten 14 2nd Lead (Conc.) 15 3rd Manganese Ore 14 Brown Coal 11 (1979) Zinc (Conc.) 10 4thSilver (Conc.) 10 Nickel 6 5th Tin (Conc.) 5 6th Black Coal 5 Gold 2 Source: Mining Annual Review 1981] The total value of all mineral and fuel exports in 1980/81 is estimated at $5.9 billion. This prominence in the world mineral production has largely been achieved in the last 15 - 20 years. In fact, in the early 1960&apos;s, Australia had only 2 major mining export centres, Broken Hill in New South Wales and Mt. Isa in Queensland. This growth is highlighted by the fact that in 1963, for example, we exported only 9 tonnes of iron ore and less than 4 million tonnes of coal. In 1980/81 we exported 75m. tonnes &apos;,of iron ore (valued at $1,117m.) and 47m. tonnes of coal valued at $1,965m.). The growth in our mineral industry has come about because of a number of factors. Abundance of Mineral Resources We are particularly well endowed with mineral resources, as indicated below.

Jan 1, 1982

By A. D. Schwope, L. R. Jackson, K. F. Smith

Burghoff and Blank1 have pointed out that the creep properties of hard-drawn coppers are closely associated with their individual softening characteristics and have further shown that the creep resistance of various types of copper is improved, under certain circumstances, by cold stretching. In the design of certain types of electrical machinery, it is important to have the creep resistance as high as possible; furthermore, short-time creep strength is important since in many cases stresses are large only during warming-up and cooling-down periods. In this paper, data are presented showing the effect of cold work on the short time creep strengths of various types of commercial copper under several conditions. It is shown that trends from short-time creep tests are evident at longer times. Materials Used in the Investigation The coppers used in this investigation were commercial grade and of two basic types, oxygen free high conductivity (OFHC) and tough pitch. Additions of silver in amounts of 15 and 25 oz per ton were added to each of the two coppers. The analyses of these six coppers are given in Table 1. Originally, they started as wire bars 4 X 4 X 54 in. A. square rod was made by hot rolling the wire bars to 9/16-in. rod in 8 passes. This rod was then cold drawn to 0.445-in.-diam rod and annealed for 3 1/2 hr at 1000°F. It was then cold drawn to 0.325-in. rod and again annealed at 1000°F for 3 1/2 hr. Hard square rods were then made by cold rolling to 0.257 X 0.257-in. rod. Soft wire was made from the hard- drawn material by annealing at 650°F for 3 hr. The final rolling was performed using a set of 9-in. grooved rolls revolving at 30 rpm, which produced square wires. Reductions of approximately 5, 20, 30, and 40 pct were obtained using several passes in the same direction for the large reductions. The 5 pct reduction by drawing was accomplished using a steel die having 2 parallel bearing surfaces. The die angle was 7 1/2 degrees and the wires were lubricated with a paste of ceresin wax dissolved in carbon tetrachloride. The speed of drawing was 13 fpm. Since work was done on only two sides of the wire simultaneously, it was necessary to rotate it 90 degrees each pass to insure uniform deformation. The room-temperature tensile properties of the various tempers are given in Table 2. The grain size of the an- nealed 0.257-in. wires was uniform and averaged about 0.035-0.045 mm. Experimental Procedures for Short-time Creep Tests Standard creep-test frames (Fig 1) were used for the testing. Special fixtures were designed to apply axial compressive and tensile loads to the copper wires. The compression specimens were 1 in. long and the ends were ground flat and parallel. The creep in compression was indicated by the movement of reference marks s-ratched on intersliding platinum strips attached to the moving heads of the fixture. The movement was measured with an optical micrometer fitted with a filar eyepiece on which the smallest division was 0.00005 in. The tensile creep specirriens were 4 in. long which provided ample gripping surface for the jaw-type grips. The platinum strips were attached to a one-inch gauge length of the wire and the creep measured as previously described. The single-specimen furnaces were connected to individual power and control sources. The controlling equipment consisted of Foxboro controllers

Jan 1, 1950

By Leonard R. Weisberg

The general properties of diffusion in GaAs are reviewed. A total of .fourteen atoms have been studied to date, and activation energies for eleven reported are (in ev): Ga (5.6), As (lo), Zn (2.49), Cd (2.43), Sn (2.5). Mn (2.75). S (4.0). Se (4.2). Ag (0.33), Cu (0.52). and Li (1.0). The dijfusion of the first eight atoms, as measured by Goldstein using radiotracer techniques, established the principle of sub lattice diffusion for both host and impurity atoms, since atoms substituting for gallium have lower activation energies than those substituting for arsenic. The diffusion constant of interstitial copper has been determined for the first time by Hall and Racette using heavily doped p-type samples in which interstitial copper predominates. The anomalous behavior of zinc, which has an abrupt diffusion front and a strong dependence on zinc concentration, has recently been quantitatively explained in terms of an interstitial-substi-tutional equilibrium-diffusion mechanism. Lithium and silver diffuse mainly interstitially, while the diffusion of phosphorus is complicated by the continual formation ofGap. Junction-migration measurements indicate diiferent results than radiotracer techniques, and this is one problem that still remains, together with discrepancies in cadmium-diffusion results, and an unexplained dependence of impurity diffusion on arsenic pressure. BESIDES the usual insights into the behavior of atoms in solids, studies of diffusion in semiconductors have additional importance for device applications. In fact, the amount of diffusion studies performed on a semiconductor might serve as a simple barometer of its technological importance. Thus, the information accumulated for GaAs is not yet quite comparable to that for germanium or silicon, but considerable knowledge is available. The diffusion of at least fourteen atoms has been investigated for GaAs, and the diffusion constants have been determined for eleven of these. Interesting results were found for GaAs that elucidated problems not previously solved for germanium or silicon. For example, the interstitial-diffusion constant for the very fast diffusant, copper, was first measured in GaAs. Also, solutions for interstitial-substitu-tional equilibrium diffusion in extrinsic material were provided first for GaAs, although they are ap- plicable to germanium, silicon, and other semiconductors. Studies in GaAs firmly established the concept of sublattice diffusion, which should have application in many different compound systems. The purpose of this paper is to review briefly the general state of knowledge concerning diffusion in GaAs. First some general aspects of diffusion will be covered, and next attention will be given to the results mentioned above. Diffusion in GaAs has been measured both by radiotracer and junction-penetration techniques, and some discussion will be given of differences in the two sets of results. The comprehensive work of oldsteinl-&apos; has served as the primary reference for the diffusion of well-behaved substitutional atoms in GaAs. Since a review has recently been presented of many of these reults, details of the diffusion data will not be repeated. Neither will any discussion be given of the experimental techniques of diffusion measurements, except to note here, in passing, the simplicity and effectiveness of the precision lapping device employed by Goldstein.&apos; I) EXPERIMENTAL RESULTS AND DISCUSSION A) Summary of Experimental Results. Diffusion constants D = Do exp(E/kT) have been determined for eleven atoms in GaAs: a,&apos; AS,&apos; n,&apos;" Cd,&apos;" n,&apos; n,8 s, e,&apos; Ag,O CU," and i." These results are summarized in Table I. In addition, diffusion was investigated for phosphorus,4&apos;12 germanium,I3 and ilicon,&apos; but Do and E were not determined. Radiotracer techniques were used for most of the studies except for lithium, where a combination of chemical and electrical techniques was employed, and germanium and silicon, where junction-migration techniques were applied. The diffusion of zinc, manganese, sulfur, and tin was also measured using junction migration.13&apos;14 Goldstein demon-

Jan 1, 1964

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,&apos; indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. &apos;The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler&apos; indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan&apos;s, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan&apos;s lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor&apos;s analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.&apos; As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1&apos;2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By E. C. W. Perryman

IN spite of the large amount of work which has been carried out on the recrystallization of aluminum and its alloys, there has been no complete investigation of the recrystallization characteristics of A1-Mg alloys. The most complete investigation is that reported by Bungardt and Osswald&apos; who, working with commercial-purity materials, found that the temperature both of beginning and of complete recrystallization increased with magnesium content up to about 2 pct Mg, then decreased with a further increase in magnesium up to 5.0 pct, and thereafter increased again. Michaud and Segolz working with 99.93 pct A1 also found the temperature of beginning of recrystallization to decrease as the magnesium content increased from 2.13 pct to about 4.5 pct. Chossat3 using aluminum of 99.99 pct purity found that 0.12 pct Mg had no effect but that 0.4 pct Mg increased the recrystallization temperature by about 30°C. That no effect was found for 0.12 pct Mg does not agree with the later results reported by Demer and Beck4 who found that 0.025 pct Mg in 99.99 pct A1 increased the time for complete recrystallization and furthermore increased the activation energy for the recrystallization process. Kratz" using 99.997 pct A1 found that 0.5 pct Mg increased both the temperature of beginning and of complete recrystallization by 100°C. Chadwick and Hooper" working with commercial-purity material found that 1 pct Mg increased the temperature of complete recrystallization by about 40 °C for cold reductions in the range 17 to 72 pct. With smaller amounts of cold work produced by stretching (10 pct strain), they found no significant effect of magnesium. The latter result agrees with that obtained by Williams and Eborall&apos; who found no effect of 2 pct Mg on the recrystallization temperature of commercial-purity aluminum strained 10 pct or less by stretching. Experimental Procedure Material Used: The chemical analyses of the materials used throughout this investigation are given in Table I. Fabrication: The alloys were cast in iron molds which had been washed thoroughly with alumina. After scalping, the ingots were annealed for 16 hr at 450°C, pressed, annealed at 450°C for 16 hr and hot rolled to 0.25 in. After hot rolling, the slabs were alternately annealed and cold rolled to 0.036 in. Cold-rolling reductions between intermediate anneals were kept at about 30 pct and a high intermediate annealing temperature of 450°C was used so as to obtain, as nearly as possible, similar starting grain sizes for the different materials. All intermediate anneals were done in a salt bath and were followed by cold-water quenching so as to retain all the magnesium in solid solution. The final cold reductions investigated were 20, 30, 40, 50, 60, and 80 pct. The initial grain sizes, that is, the grain size before the final cold reduction, were all very similar. Annealing Procedure: Specimens, 1 in. sq, were cut from the 0.036 in. sheet and annealed in a salt bath, the temperature of which was controlled to k2"C. Separate specimens were annealed for different times at 350°, 375", 400°, and in one or two cases at 415°C and after annealing were quenched in cold water. The time taken for a specimen to reach temperature was approximately 5 sec. Metal-lographic examination after annealing showed that no precipitation of Mg+413 occurred during cooling. Procedures Used for Determining Recrystallization Characteristics: All specimens were electrolyti-cally polished and etched by the method described previously1° and polishing was continued until about 0.002 in. had been removed from each side of the specimen. Using this technique, the smallest recrys-tallized grain which could be observed with cer-

Jan 1, 1956

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker&apos;s reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,&apos; it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,&apos; the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1&apos;3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By N. K. Chen, R. Maddin

Columbium single crystals were deformed in tension and compression. Reorientation by X-rays and stereographic projections of slip traces indicate that plane of slip may be considered as (110). The plastic behavior is shown to be quite similar to the deformation of molybdenum single crystals. STUDIES on the crystallography of the deformation process in body-centered cubic metals have been renewed recently with investigations of iron single crystals1-" and molybdenum single crystals.4 It is now apparent that too many exceptions to the rationalization based upon the ratio of absolute testing temperature to absolute melting point by Andrade5 exist to permit more serious discussion of this type of analysis. The considerations of resolved shear stress utilizing only planes of the type {ll0}, {112), and {123)³,6 permit analysis of the deformation only on the basis of those three types of planes. The suggestions made by Elam7 and by Greninger8 in which the slip process is envisioned as a composite slip on two nonparallel {110) planes can be illustrated schematically in Fig. 1. It may be seen that an unresolved trace on any plane containing a <111> direction may be accomplished by varying the number of atoms participating in the composite process. By further varying the number of atoms in each plane but keeping the ratio of participating atoms constant, jogs could be obtained in the traces and hence wavy slip lines could be produced. Vogel and Brick&apos; studied the behavior of a iron single crystals in which they suggest that the plane of glide is "non-crystallographic" and may be predicted from the intersection between the great circle joining the slip direction and specimen axis with the great circle whose zone axis is the slip direction. In a more recent investigation on iron single crystals, Steijn and Brick" suggest that the slip mechanism may be considered as made up of a type of composite slip occurring on {110} and {112} planes. Evidence for a possible composite nature of the slip process has been presented for the case of molybdenum in the form of analysis of asterism and specimen axis rotation." Definite proof of a composite slip process must, however, await good electron microscopic resolution of the individual traces making up the unresolved optical trace used in determining the acting slip plane. The present investigation was undertaken to study the behavior of columbium single crystals not only in tension but also in compression since the specimen axis migration should indicate the plane or planes of glide in the same manner that the specimen axis migration in tension indicates the direction of glide. The orientations of eleven crystals investigated are shown in Fig. 2. Specific orientations are missing (those in the vicinity of [Ill] and [001] and consequently the effect of orientation on the crystallography of deformation could not be considered. Experimental Procedure The 1/8 in. rods (7 in. long) were subjected to an axial tension in vacuo while at temperatures in the vicinity of 2000°C for 2 to 4 hr. This treatment resulted in large cylindrical grains (about ½ in. long) occupying the entire cross section. A number of these rods were used for the tension studies by observing the behavior of the individual grains. For the compression studies, single crystals approximately % in. long by 1/8 in. in diameter were cut from the rods; the ends were ground parallel. All specimens were polished electrolytically in a solution of 15 cc HF(48 pct) and 85 cc H2SO4 (concentrated) using a platinum cathode, a current density of 0.04 amp per sq cm and a temperature between 25" and 60°C.10 Orientations were obtained using a Laue back-reflection method (3 cm film to specimen distance) with a ½ mm collimator 9 cm long. For the compression specimens, a reference mark was scratched on one of the compression sur-

Jan 1, 1954

By Hisaaki Takata, Nobukazu Nanko, Ichiro Izawa

INTRODUCTION Tochibora Mine belonged to Kamioka Mines, which are located in Gifu Prefecture, the cen- tral part of the Japanese main island, has occupied the important position as a main source of silver, lead and zinc for the smelter of Mitsui Mining & Smelting Co., Ltd.. The annual production of crude ore goes up to about 1 mil- lion metric tons with average grades of 20g/t Ag. 0.31% Pb, and 4.18% Zn. For the last 20 years, the mine has struggled with the depressed zinc metal price in yen and the escalation of operating cost, especially la- bour cost. For instance, prices of commodities and labour cost have been raised 8 times and 14 times respectively during this period. On the other hand, total operating cost has been con- trolled to increase 4.5 times. The productivity of the mine has been increased 4 times by means of improvement of individual works and adoption of perfectly mechanized trackless mining system to reform the mining method. Some improvements are presented as follows; Today, drifting is carried out by the tunnelling crew which consists of 9 operators equipped with 5 Mobile-Jumbos, 2 LHD&apos;s and a jeep for carrying and loading ex- plosives. In order to get the high utilization of these machines, each crew manages systematically and continuously adjacent 15 faces under the direction of a forceman. As a result, we have accomplished high advance of drift. Furthermore, raising is carried out by a set of the raise-borer in case of long raises like ore- passes and also by the stage blasting method in case of short ones like slot-cuts. Generally speaking, the sublevel stoping method is considered to be one of the best methods for various respects; high productivity, low cost, easy grade control and safety. This method has been introduced in Tochibora Mine since 1950 and is now widely applied to lodes that could not be mined before by this method be- cause of the shapes of them and the conditions of their country rock. Now we are convinced to be nearly accomplished for our method. This report presents some examples of the standard sublevel stoping method and its variations which are practised at the mine. STANDARD SUBLEVEL STOPING Up to 1979 since 1950 when this method was first applied at the mine, 17 million tons of crude ore have been produced by this method, which amounted to 55% of the total production of the mine. During three decades, the productivity has been increased considerably by means of trackless mining system using large-sized machines and etc.. In other words, mining efficiency has been increased from 20 tons/man.shift to 100 tons/man.shift at large stopes. Formerly undercutting was carried out above the drawing drift by jack-legs and small scrapers and then several cone-shaped glory holes were made by stopers between the undercut level and the draw level. But now, a undercut drift is driven in parallel with the haulage drift at the same level of it. And at the undercut drift, drilling upward is carried out by a large-sized machines like the fan drill in order to extract the broken ore directly at the drawing drift connected with the haulage drift. Simplification of the work as well as utilization of large- sized machines enables to get higher productivity. But if the deposit is comparatively wider and the broken ore around the middle part of the deposit cannot be extracted, several drawing drifts are driven to the deposit and in order to minimize dead ore at the final stage of operation, the

Jan 1, 1981

By J. Jones-Parra, J. C. Calhoun

INTRODUCTION The purpose of this paper is to present the results obtained by solving the fractional flow&apos; and frontal advance&apos; equations to obtain oil recovery at water breakthrough as a function of the length of the system being flooded, the linear velocity of injection and the displacing phase viscosity. The method of solution makes use of the stabilized zone concept first presented by Terwilliger, et al3 when calculating saturation distributions in a gravity drainage system. In order to check the calculated results, the equations and method of solution were applied to the system on which Rapoport and Leas&apos; reported experimental data. METHOD OF SOLUTION The solution of the fractional flow equation and the frontal advance equation is obtained by assuming that a water front forms to sweep the oil out ahead of it. There is ample evidence that under the proper conditions a water &apos;front does form. If this water front is not to dissipate, the water saturations which comprise it must have equal linear velocities. These water saturations are said to comprise the stabilized zone. Equation (2) indicates that for all these saturations and hence fw must plot as a straight line against saturation for those water saturations comprising the stabilized zone. The water saturations lying between the highest in the stabilized zone and the highest that can be achieved in the porous medium comprise the variable zone. Regardless of the numerical value of the length of the system, the variable zone must eventually span all of it, so that for long enough systems in Equation (1) will be small enough to be neglected. Hence, for the saturations in the variable zone Equation (1) can be simplified to In order to determine the composite fw function applicable to the entire range of saturations in the porous medium, it is necessary to find the water saturation which separates the stabilized zone from the variable zone. This dividing saturation must be on the curve defined by Equation (4), and a tangent curve at that point must pass through the initial water saturation to satisfy Equation (3). Hence, the valid fw curve is given by a straight line starting at the initial water saturation, tangent to the curve of Equation (4): and along the curve of Equation (4) from the point of tangency on. The point of tangency determines the water saturation dividing the zones. The length and shape of the stabilized zone can be found by solving Equation (1) for Integrating this expression numerically between any two saturations in the stabilized zone gives the distance separating these two saturations. By repeated integration, the saturation distribution of the stabilized zone can be determined. The total length of the stabilized zone is given by The integral appearing in Equation (5) is a function of the viscosity ratio, the capillary properties of the rockfluid system, the relative permeabilities, and the initial water saturation. Considering these variables fixed and designating the value of the integral by writing caw for and v/60 for q/A; Equation (5) becomes The saturation distribution of the stabilized zone can be integrated over its length and divided by the length to obtain the average water saturation The volume of water in the stabilized zone is then given by The average water saturation in the variable zone can be found by extending the straight line segment of (the segment joining Sw and Sw) until it intersects fw = 1.00. The saturation at the intersection is. This method of finding is nothing more than the graphical solution of the equation The volume of water in the variable zone at breakthrough is then given by Assuming no initial water saturation, the recovery at breakthrough expressed as percent pore volume is given by

Jan 1, 1953

By P. T. Bail, J. E. Bobek

In reservoirs containing soft shales interbedded with oil-producing sands, it is possible to have water movement from the shales into the sands during reservoir depletion. This paper presents the results of scaled flow-model tests performed to investigate the efficiency of oil displacement by this vertical influx of water into oil-producing sands. In these model tests, the effects of rate of influx and rock wettability were considered. Oil recoveries by shale-wafer influx and by water flooding were cornpared after 0.4 hydrocarbon volume of water entered the producing sand. This comparison was made for water-wet and oil-wet systems. In water-wet sand, shale-water influx produces slightly less oil than conventional water flooding; in oil-wet sand, shale-water influx produces about one-half as much oil as conventional water flooding. In another type of comparison, it was found that shale-water influx followed by water flooding recovers less oil than water flooding alone. This is true for both water-wet and oil-wet sands. A comparison of tests run at different rates of shale-water influx shows that oil recovery is insensitive to rate in water-wet sand; in oil-wet sand, oil recovery decreases with decreasing rate of influx. INTRODUCTION Localized subsidence of the earth&apos;s surface has accompanied the depletion of some oil reservoirs, particularly in California,1, 2 along the Texas Gulf Coast,3 4 and in the Bolivar Coastal fields of Venezuela. Subsidence occurs when fluid withdrawals reduce the pressure in the reservoir. The reasons for subsidence accompanying a reduction in reservoir pressure are not known with certainty.10° However, there is considerable evidence that compaction of soft shale beds adjacent to producing oil sands can be a major cause of this subsi-dence.3, 6, 10-12 When the shales compact, a limited amount of water moves from the shales into the producing sands. A schematic illustration of this oil-producing mechanism is shown in Fig. 1. As the pressure in the sand declines due to oil production, a predominantly vertical pressure gradient develops at the sand-shale boundary. This causes water to move from the shale into the sand as indicated by the solid arrows. This paper reports the results of scaled flow-model tests to investigate the efficiency of oil displacement by the vertical influx of shale water into producing sands. The model tests were not performed with the aim of duplicating the recovery behavior of any specific reservoir. The primary purpose of the tests was to obtain a better understanding of oil displacement by shale-water influx. A knowledge of the oil- and water-production characteristics of even a simplified reservoir system should be of value to engineers estimating the performance of reservoirs where shale-water influx is occurring in conjunction with other production mechanisms. The following limitations and assumptions apply to the model work. 1. The sand of the prototype reservoir is homogeneous and horizontal. 2. The shale-water influx is uniformly distributed along the top and bottom of the sand member being studied. 3. No effects of edge-water drive or dissolved-gas drive that might accompany shale-water influx are considered. PROTOTYPE RESERVOIRS Scaled-model tests were performed to study oil displacement from three prototype reservoir sections. The reservoir sections modeled consist of single sand layers out of a sequence of -sand and -shale layers, as illustrated in Fig. 1. Each prototype represents a homogeneous, high-permeability, unconsolidated sand layer. In the field, the prototype is oriented in such a manner that one end is at the radius of drainage of a producing well and the other end is pointed toward the producing well (Fig. 2). The sand and fluid properties and the dimensions of the three prototypes are given in Table 1. The capillary pressure relationships for the three prototypes are presented in Figs. 3, 4 and 5. The oil-water per-

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956