Search Documents

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

The Lornex mine is located in the Highland Valley area of British Columbia, Canada, one of the most,promising districts of low-grade porphyry-type copper mineralization in the world; Lornex is operated by Rio Algom Mines, Limited, a member of the Rio Tinto Zinc Group of London. Exploration from 1965 to 1968 disclosed an ore body of 293 million tons with a grade of 0.43% copper and 0. 14% molybdenum; this led to the decision to construct a 38,000 tpd operation, and production commenced in the fall of 1972. The ore is open-pit mined with 15 cu yd (11 5 m3 shovels, which load 100- and 200 -ton trucks. These trucks dump directly into a 60 in. by 89 in. Allis -Chalmers gyratory from two sides of the 14 ft 6 in. (4.42 m) deep dump pocket and across splitters mounted on the pocket sides. The unlined pocket would hold 1,000 tons level full. The crushedore discharges into a 300-ton surge hopper equipped with an automatic sonic level indicator to prevent over -filling. A 96 in. by 23 ft (2.44 m by 7 m) apron feeder delivers the ore from the surge hopper to a 72 in. (1.83 m) transfer belt equipped with a tramp iron metal detector. The transfer belt discharges to a 60 in. (1. 52 m) conveyor which conveys the ore about 3,000 ft (914 m) to the 475,000 ton ore storage pile located near the concentrator. Four 48 in. (1.22 m) pan feeders transfer the ore to the mill feed conveyors, which in turn supply the two 32 ft by 15 ft (9. 75 m by 4. 57 m) semi-autogenous mills, which easily accept the 10 in. (254 mm) product of the crusher. Each semi- autogenous mill is followed by a secondary ball mill. The unusually large open side setting of the crusher accounts for its 6,300 tph maximum capacity. Concentrator capacity is now 48,000 tpd. Eccentric removal is eased by the design of the door to the crushed ore pocket, which has the cart rails mounted on its outer surface and is lowered to a horizontal position in the pocket by an electric winch. The top of the door rests on wear bar covered concrete piers in the pocket. Another feature is a chute through the floor at the crusher base that extends into the crushed ore pocket. Dust and spills of ore on that floor during crusher repairs are easily swept into the crushed ore pocket. This feature is also used at Bougainville and Palabora and has been added to others after operation has commenced. The design follows the concrete rectangular box concept with four main service and maintenance levels shown in the sectional drawings, although a third additional section has been added at the maintenance

Jan 1, 1978

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,' from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,' from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By John P. Dolan, Charles A. Einarsen, GiIman A. Hill

his paper discusses how the following formation characteristics can be determined mathematically from drill-stem test pressure charts: true formation pressures, effective permeability of the entire section tested, well productivities, wellbore damage, and possible detection of barriers (faults, pinchouts, etc.). This paper also presents a practical method for im-mediate determination of eflective permeability and well-bore damage from successful double shut-in pressure tests. A list of recommendations for improving the reliability of drill-stem rest pressures is also presented. INTRODUCTION A drill-stem test is a temporary completion designed to sample the formation fluid and to establish the possibility of commercial production. Early pressure recording devices were used merely to verify proper operation of the testing tool. Until recently the accuracy of the pressure gauges has been insufficient for any reliable quantitative use of the recorded pressures. In view of the need for more reliable formation evaluation and as a result of the recent interest in exploration work employing the concept of hydrodynamic en-trapment,1,2,3,4 better pressure recording gauges are now in use. These devices can record pressure within 1 per cent above 1,000 psig and can detect differential pressures as low as 1/2 psig. In addition to formation pressure, several other reservoir characteristics can be determined from DST charts; namely, well productivity, formation permeability, wellbore damage, and the possible existence of bar- riers (faults, pinchouts, changes in permeability, etc.). This paper presents a practical method to interpret DST pressure charts for formation pressures and many other reservoir properties, a method that has been developed in analyzing approximately 4,000 DST charts during the last five years. The techniques used are a composite of published articles on drill-stem testing5,6, together with well-known pressure build-up analysis methods. THEORY It has been shown7,8 that the following equation may be used for analysis of pressure build-up curves: Po - Pw = 162.6 qu/kh log ( to + ?/?) .....(1) When this equation is applied to the curves obtained in drill-stem testing, the assumptions and boundary con-ditions are more nearly realized than in conventional flow and build-up tests on producing wells. Zak and Griffen9 have recently discussed in detail the use of this equation in analyzing DST charts. One of the problems with DST curves is the lack of reservoir data for precise analysis. Therefore, it is necessary to develop empirical rules and field methods for analyzing DST charts in quantity. For this reason, the empirical methods presented in this paper have been developed, and their derivation is found in Appendices A and B. METHOD USED FOR ACCURATE READING OF DRILL-STEM TEST CHARTS In order to apply the pressure build-up theory to DST charts, it is necessary to obtain a digitized expression for the pressure and time data recorded by the pressure gauge. These data may be either provided by the service company or interpolated by projecting a

Jan 1, 1958

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By E. Horton Jones

CONTENTS I Page Introduction ....:......................... 3 Chapter I. Unit Costs. . ...................... 4 Chapter II. Comparative Costs ..................... 20 Chapter III. Composite Costs..................... 32 Chapter IV. Wage Scale....................... 36 Chapter V. Raw Material Prices................. 37 Chapter VI. Description oF Costs ................... 64 Introduction We have endeavored in the following "sheets" to give the unit construction costs derived from 'the building of the Arizona Copper Co.'s new smelter, Clifton, Ariz., starting in February, 1912, and completing February, 1914.l In Chapter I—Unit Costs—are to be found the most elementary total unit costs which the accounts provide for. They are usable in the Clifton district. Here too are found the percentages to be added to an estimate for Engineering and General Expense. In Chapter II—Comparative Costs—these elementary costs have been classified, averaged and reported as labor and material unit costs. In such form the labor unit costs, when properly applied to similar conditions as these under which they were derived, are usable anywhere. The material unit costs are better disregarded for more accurate estimates and replaced by a newly priced bill of material. In Chapter III Composite Costs are given. They are unit costs built up from several elementary units, and likewise units of larger dimensions and simpler application, valuable for

Jan 1, 1915

By D. A. Elgillani, M. C. Fuerstenau, M. C. Kuhn

The species responsible for flotation when xanthate is added as collector for pyrite is dixanthogen. Measured oxidation potentials of these systems show that xanthate should be oxidized to dixanthogen, and the presence of dixanthogen on the pyrite surface is confirmed by infrared absorption. Zeta potential measurements are presented and related to collector adsorption. In spite of the normal presence of pyrite in most sulfide ore deposits, only a modest amount of study has been devoted to the xanthate-pyrite flotation system in the absence of activators and depressant~.'-~ As a result, little is known about the mechanism of xanthate adsorption on pyrite. From the few studies that have been made, however, a number of significant observations have been forthcoming. For example, the dependence of flotation response on the state of oxidation of the surface was noted in two studies — one conducted by Plante and Sutherland4 and a later one by plaksin.~ In another study, Gaudin and wilkinson3 found that ferric xanthate was not present on a pyrite surface. In a later investigation, however, Gaudin' and his colleagues did extract a small amount of ferric xanthate into benzene when pyrite was ground in an evacuated mill with water, benzene, and xanthate. This quantity was apparently

Jan 1, 1969

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration 10 Oil-field statistics : 12 Description by regions: United States: Appalachian region ; 12 East-central states 17 Kansas 18 Oklahoma : 19 Texas : 24 Arkansas : 32 Louisiana 33 Mississippi ....... 34 Rocky Mountain region : 34 California 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account- of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By G. Ansel, J. O. Betteron

THE PURPOSE OF THIS PAPER is to give a brief picture of present day magnesium rolling practice, to elaborate on laboratory and development rolling experiments; and finally, to discuss the possible Future rolling of magnesium. The present production practice is so varied between various mills that it can only he concluded that no single producer is now using a process that is outstandingly superior to others. In view of this, only the general features of present day production practice have been presented and attention is focussed on the results of laboratory find development rolling of magnesium-base alloys as indications of the Future trend of magnesium rolling. MAGNESIUM ROLLING LITERATURE The literature relating to magnesium rolling is divided into three groups: the deformation mechanisms of the hexagonal magnesium crystals, the metallurgical aspects and laboratory type experiments in rolling, and finally, the articles on production rolling methods. This literature was reviewed and is summarized below. In the first group of references, the existence of basal slip in magnesium single crystals was shown by Schiebold and Siebel1 and of {102} twinning by Mathewson and Phillips2, Schmid3 predicted and partially established {101} slip at hot working temperatures. Bakarian and Mathewson4 confirmed the above and eliminated {101} twinning as a probable deformation mechan-

Jan 1, 1948

By P. D. Merica

ALUMINUM and its alloys have been the subject of much investigation, during recent years, in the course of which the principal features of the constitution of most of the binary alloy systems with aluminum have been determined. Except in the case of a few metals-silicon, bismuth, cadmium, lead, zinc, and tin-an aluminum-rich compound is formed in each binary system, which forms a eutectic with the aluminum or its solid solution with this compound. Thus such compounds as FeAl3, CuAl2, Mg4Al3, and NiAl3 are formed, which are found in aluminum-rich alloys of their respective series as eutectics with the aluminum solid solution. These compounds are, in all cases, hard and brittle and their presence affects profoundly the physical properties of the alloys in which they occur. Within the zinc-aluminum system a compound, Al2Zn3, is formed that decomposes at lower temperatures. Silicon and tin each form a simple eutectiferous series with aluminum; bismuth, lead, and cadmium are only partly miscible in the liquid state with it. The extent of the solubility in aluminum, in solid solution, of these compounds or of the elements themselves, in the case of those series

Jan 7, 1919

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By J. C. Coughlin, M. C. Flemings, T. Z. Kattamis

Experiments on Al-4.5 pct Cu alloy shou the dendrite arnz spacing increases with time during isothermal holding in the liquid-solid region. This coarsening of the dendrite structure is then shown to occur at roughly the same rate during solidification as during isothermal holding. Final dendrite arm spacing in both types of experiments depends primarily on coarsening kinetics. It is concluded that driving force for the coarsening is reduction of liquid-solid sur/ace area. Calculations based on two simple models show qualitative apreement with experinzent. 1 HERE has been considerable interest in recent years in determining effects of solidification variables on dendrite arm spacing in cast alloys. The interest has resulted primarily from the clear evidence that 1) the degree of homogeneity which can be obtained in a cast alloy with commercially practical homogeni- zation treatments depends on dendrite arm spacing, and 2) mechanical properties of the heat-treated casting depend on the homogeneity obtained.'-' In wrought alloys, microsegregation from the original ingot is carried to some extent into the final wrought product, and affects mechanical properties in similar fashion Experimental evidence available indicates that dendrite arm spacing in cast aluminum alloys is influenced only by cooling rate (or "local solidification timev*) and alloy content.Fig. 1, for example,

Jan 1, 1968

By A. C. Dittrick

THE Simon-Carves washer, originally known as the Baum jig washer, was first built in Europe about 1892. It was probably the first washer to use intermittent pressure of air on water in one part of the wash box to obtain water pulsations in another part. This type of washer was also the first to successfully clean various sizes in the same unit. Previous practice was to size closely before washing. Today there are several large firms abroad, and a few in the United States, that are constructing the Baum type washer. The design of all is practically the same, their differences being only in details. In 1928, the Hanna Coal Co. first gave consideration to the question of coal cleaning. It was believed at that time that by efficient removal of so-called noncombustibles appearing in the Pittsburgh No. 8 seam, certain markets that had been lost due to poor preparation might be recovered. Mechanical cleaning and mechanical loading were under consideration. This type of cleaning was considered the most practical means of removing impurities in the sizes below 4 in. It was decided to adopt mechanical cleaning and develop a system of mechanical loading that would be successful on No. 8 coal.

Jan 1, 1935