Search Documents

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Frederick Forscher

Frederick Forscher (Nuclear Materials and Equipment Gorp.)—It is gratifying to see another series of experimental results that essentially reconfirms our reported observations of "Strain-Induced Hydrogen Embrittlement in Zirconium" (F. Forscher: AIME Trans., 1956, vol. 206, p. 536, noted as Ref. 3 of paper). However, several important considerations may have been overlooked, or—at least—have not been specifically pointed out. It is the purpose of this discussion to present some of these considerations. The statement is made that "the equilibrium concentration of hydrogen in solution at 20°C in zirconium is approximately 10 ppm; i.e., no zirconium hydride precipitates are formed at or below this hydrogen content." This is perhaps the case in the unstressed condition. In the presence of triaxial (plastic) strain however, even as little as 1.4 ppm H2 (Forscher's Figs. 6 and 11) will cause porosity near fracture in 20°C tests. The necked-down region that develops during a tensile test provides the triaxiality necessary for these pores to open. Both Beevers' and Forscher's micrographs show that porosity is concentrated in the necked region. So-called "pure zirconium" containing about 10 ppm H2 also shows pronounced porosity near fracture (Beevers' Fig. 3). Since it is generally agreed that such porosity is

Jan 1, 1965

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By D. M. Wade, F. F. Redfield

PRODUCTION at Aguilar started in 1936 and by 1942 the mine had reached a peak of 25,000 tons a month. Present production is only about 60 per cent of this capacity because of difficulties in railroad transportation and the rationing of fuel oil brought about by the war. In the early years, cut-and-fill stopes were tried, but square sets were found to be the most practical method in the southern section of the mine, where blocky, treacherous ground and greater mining widths are prevalent. Square sets and opencut mining were the rule until 1942, when it became increasingly difficult to get mine timber. The ore beds in the northern section of the mine were found amenable to cut-and-fill stoping as the rock was firmer and the veins narrower. At present 69 per cent of the ore comes from cut-and-fill stopes, 27 per cent from opencut, and only 4 per cent from square-set stopes. Massive galena and sphalerite with comparatively little quartzitic gangue constitutes the higher-grade ore. The gangue minerals that can be detected by eye in low-grade ore are rhodonite, wollastonite, and pyrrhotite. Wall rocks range from shale to quartzite, with occasionally a little limestone.

Jan 1, 1947

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By G. Willard Quick

TENSILE tests of rail steels at elevated temperatures'' have shown that certain rails, in addition to having low ductility in the well-known bluebrittle range in the neighborhood of 200° C., have marked reduction in elongation and reduction of area in the temperature range from 400° to 700° C. This range of low ductility was called "the secondary brittle range" and the phenomenon, "secondary brittleness." The question naturally arises as to whether this property of the steels would be shown by impact tests performed in the same range of temperature. If so, the impact test, as suggested by Gillett3 would be a simpler and quicker method for the routine examination of steels at elevated temperature than the tensile test. A number of investigators have reported results of impact tests on steels at elevated temperatures, in which the energy absorbed decreased with increase of temperature above 200° or 300° C. Langenberg4 performed Charpy impact tests on several steels at temperatures ranging from room temperature up to 1000° F. (538° C). His results showed an increase in the energy absorbed in specimens tested in the range from room temperature to 200° or 300° C. and then a gradual decrease in the range, 300° to 538° C., the maximum temperature used. Greaves and Jones5

Jan 1, 1932

By John L. Burns

The object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-hardening characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classification" is essayed. A.—Relation of Lattice Parameter and Electrical Conductivity to Changes in Physical Properties Due to Aging of Fe-C Alloys Since Whiteleyl in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A, point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,~ and at the same time and independently, W. Koster,~ proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By Peter L. Raffo, Walter R. Witzke

RHENIUM has a melting point of 5750°F, the second highest value among the metals.1 Its refractory nature should thus make it a useful material at high temperatures. The only available data on the high-temperature properties of bulk rhenium are from the work of Flagella and Tarr.2 These authors have shown that, over a wide range of temperatures and stresses, no appreciable linearity exists in a log-log plot of the minimum creep rate or rupture life vs stress. The purpose of the present letter is to describe some exploratory experiments designed to study the creep rate-stress-temperature relation and other facets of the creep of rhenium. The tests were carried out in vacuum in the temperature range 2200" to 4000°F (0.43 to 0.72 Tm,) at stresses ranging from 4 to 20 ksi. The powder metallurgy rhenium was purchased as 0.04-in.-thick sheet. The sheet is nominally 99.97 pct pure with the major impurities being iron (70 ppm) and molybdenum (25 ppm). The sheet was machined into specimens having a 1-in. gage length and a 0.25-in. gage width. The specimens were preannealed in hydrogen at 3000°F for 1 hr. This treatment produced

Jan 1, 1970

By T. Clinton Taylor

QUALITATIVELY, galena (native lead sulfide) reacts with aqueous solutions of the xanthates,1 and has its surface sufficiently altered so that there is a tendency for air bubbles to attach themselves to the mineral crystals where there was no such effect before the treatment. This property is utilized in froth flotation operations where the mineral sulfide particles are raised into the froth and the gangue whose surface is not altered remains behind. The results of a study of this reaction were reported" recently and certain tentative suggestions about the interaction of galena and the alkali xanthates were offered. In this paper, there is set down the results of a detailed quantitative investigation of the ions involved in this inter-action with a view to finding out more about the condition existing imme-diately at the surface of a crystal like a heavy metal sulfide after treatment with an organic reagent. Past experimental experience showed that finely ground galena shaken with aqueous potassium xanthate abstracts xanthate ion and at the same time sulfate ion, reducing ions of the type (SmOn)= where the ratio of m to n is less than 4:1 (as in sulfate), sometimes hydroxyl ion are thrown into solution.,

Jan 1, 1933

By D. O. Noel

IT is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise remov-ing one of the alloying constituents.

Jan 1, 1938

By C. H. Herty

AN earlier paper on absorption of sulfur by the slag in the basic open-hearth furnace included a brief discussion of the absorption of sulfur during the melting period. The data available at that time showed that the amount of sulfur absorbed by the melting scrap was proportional to the sulfur content of the furnace gases, and the following statement was made: "The conclusion may be drawn from these results that if a gas entirely free from sulfur were used during the melting, any iron in direct contact with the gases would be completely, or nearly completely, desulfurized before it reached the bath proper." The experimental work discussed herein deals with absorption of sulfur by the melting scrap when fuels with both high and low-sulfur content were used. Before taking up the experimental work let us consider the process as a whole as to the "flow" of sulfur. The input of sulfur occurs in: 1, the hot metal charged; 2, the scrap; 3, the stone or lime charged; 4, the ores charged; and 5, the gas. Sulfur goes out of the furnace in the steel, the slag and the gas. The distribution of sulfur in the furnace depends on the sulfur concentration in each of these materials and on the equilibrium conditions between them.

Jan 1, 1926

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By Edward Martinez

The literature on the beneficiation of serpentine asbestos ore states that the specific gravity of the rock containing fiber and the fiber itself is the same so that specific gravity cannot be used as a basis for separation. An investigation of particles of asbestos ore ranging in size from 4 mesh to 5 in. revealed that the fiber-bearing particles generally had a lower specific gravity compared to essentially barren particles. The difference in specific gravity was sufficient to make an effective gravity separation of ore particles and reject a low grade tailings product. The results of laboratory tests are described that lead to the running of pilot plant tests with 20-ton ore samples using a heavy media separator. These tests indicated that a large amount of low grade material could be rejected from the raw ore at a coarse size. Although the process used is a wet separation, it can be added to a conventional dry asbestos mill. A gravity preconcentration would allow the mining of lower grade ore, increase the life of the mine, increase the value of the feed to the fiber recovery section, and decrease maintenance costs by removal of low grade tailings early in the flowsheet.

Jan 1, 1975

By R. H. Moore

The data for diffusion in dilute binary alloys with the Solvents Ag, Cu, Ni, Fe. Al. and Pb hare been correlated as a function of atomic volume. Linear equations of the form: Q = b - a log V are obtained with constants "a" and "b" ciuirac-teristic of each solvent metal. In most cases. 3-d In recent years measurements of diffusion coefficients in solid binary alloys. using small concentrations of radioactive isotopes. have resulted in accumulation of highly reproducible data. Such and 4-d transition elements correlate on separate straight lines from those which serve to correlate the non/ransition elements. The data for the uon-transilion elements diffusing in silver and copper liave been fitted by least-squares analysis. It is concluded that the size and charge effects which determine the magnitude of the activation energy for diffusion are a function of atomic volume. systems represent the simplest possible examples of chemical diffusion since solute interaction effects can be neglected and Kirkendall-like phenomena do not occur. Generally it is found that thc diffusion rate of the solute is within an order of magnitude of the diffusion rate of the solvent. The differences have been attributed to the effect of size and to electrostatic interactions between the solute and solvent atoms.

Jan 1, 1965

By Horace Pops, Jorge E. Kittl

In a recent study' of the martensitic transformation of Cu-Zn ß-phase alloys, it was noted that the MS temperature at the surface was raised due to the loss of zinc by volatilization. It seems likely, therefore, that the MS temperature may serve as a guide for the measurement of composition. From a knowledge of the dependence of the transformation temperature on composition, 2 it should be possible to detect variations in zinc content which are less than 0.1 at. pct by measuring the MS temperature throughout the sample. It is unlikely that an electron microprobe analysis could detect accurately such small zinc losses because the presently accepted limits of accuracy of the micro-probe analysis in simple ternary systems are of the order of 2 to 5 pct of the amount present.3 In the present study, a composition gradient was produced by precipitating the a primary solid solution, and reheating for a very short time within the ß-phase field. The nominal composition, in atomic percent, of the ternary ß-phase alloy used, 64.2 Cu, 34 Zn, 1.8 Si, was selected because it had an MS temperature of +4°C, thereby simplifying the experi-

Jan 1, 1968

By Norman C. Britz, Mortimer P. Buck

THIS PAPER DEALS WITH the practices used at the Huntington, Nest Virginia works of The International Nickel Company, Inc., in hot and cold rolling nickel and high-nickel alloys. The practical metallurgical aspects are discussed and a brief description of equipment given. The alloys covered may he divided into three main groups. based on their major constituents: 1. Nickel alloys, 2. Nickel-copper alloys. 3. Nickel-chromium alloys. The nominal compositions of the various alloys which are produced in most common mill forms are given in Table 1. Nickel, a commercially pure grade of nickel containing about 0.05 pct carbon as' the chief alloying element, is produced in all common Mill forms. "L" Nickel is commercially pure nickel in which the carbon content is held as low as possible, usually less than 0.01 pct. This grade of nickel is used chiefly for spinning and for special high temperature applications where its low carbon content enhances its corrosion resistance. "D" Nickel contains 4.5 pct manganese to provide improved resistance to sulphur embrittlement at elevated temperatures. "Z" Nickel is an age hardening grade of nickel containing carbon, aluminum, and silicon as the age hardening elements. This alloy combines the cor-

Jan 1, 1948