Search Documents

By J. W. Evans

ONE possible method for the separation of hafnium from zirconium is by the vapor phase oxidation of the purified mixed chlorides. An important factor for success depends on the difference in free energies of the following reactions: ZrCl(g) + O2 = ZrO2(s) + 2C12 [1] HfCl4(g) + O2 = HfO2(s) + 2C12. [2] Prakash and Sundaram1 have calculated these values from certain data and carried out experimental work with partial success. However, their free energy values for reaction 2 diverge rather widely from other data which are presented here. The possibility of successful separation is briefly considered in the light of these alternative values. Table I shows the free energy values (?F°) for reactions 1 and 2 derived from the recent compilation of data on oxides and chlorides by Glassner.2 The corresponding values of Prakash and Sundaram for the same temperatures are also shown. The alternative values to those of Prakash and Sundaram for reaction 2 are substantially confirmed by the data of Kubaschewski and Evans" and Cough-lin' on heats of formation, entropies, and heats of vaporization. In spite of the considerable uncertainty in the hafnium data it is reasonable to suppose that the oxide-chloride free energy difference for two such chemically similar elements would not be very far apart. These figures indicate clearly that the oxidation of hafnium chloride is appreciable at all temperatures. Nevertheless, there is a significant difference between the values for reactions 1 and 2

Jan 1, 1959

By W. R. Wawersik, A. M. Starfield

The classical approach to room-and-pillar mine design in flat-lying, tabular ore bodies limits itself to the special case of an extensive and uniform system of pillars. Each pillar is then assumed to carry the same load, and this load is readily calculated from the extraction ratio e and the weight of the overburden : average pillar stress = [ ] where H is depth below surface, p is average density of overburden, and g is acceleration due to gravity. The average pillar load does not, in this case, depend on the mechanical properties of either the pillars or the surrounding rock mass. The only relevant physical property of the pillars is their compressive strength, (i.e., the maximum load-carrying ability) and the criterion for design is that the average pillar stress should not exceed this strength. The wider the pillar, the greater its strength, and the design of the system is concerned with reconciling this increase in strength to the requirements of roof control so as to optimize extraction.l Any departure from a uniform distribution of pillar loads invalidates the classical approach. Such departures may, for instance, be brought about by: (1) a nonuniform layout of pillars and remnants resulting from selective mining, (2) variations in geology which result in gross changes in the properties of part of the seam or the host rock, (3) deliberate use of abutment support in narrow panels, and (4) the use of yielding pillars for local roof support in conjunction with barrier pillars to carry the overburden load.

Jan 1, 1972

By E. H. Cho

INTRODUCTION Activated charcoal has been used for several centuries in many capacities including the recovery, isolation and purification of various materials (1). The first use of charcoal in a gold metallurgical system was in the extraction of gold after chlorination (2, 3,4). The gold was dissolved in a chlorine system and subsequently filtered through charcoal. The application of charcoal with cyanide extraction was patented by Johnston (5) in 1894 and adopted commercially in Australia in 1897. The process consisted of dissolving the gold and silver in a potassium cyanide solution and passing it through a series of charcoal filters. The charcoal was subsequently smelted to recover the gold and silver. The interest in the use of charcoal diminished in the first part of the twentieth century as the practice of the use of zinc as a precipitating agent increased. However, in 1916, the Yuanmi Mine in Australia replaced their zinc precipitation plant with a charcoal adsorption plant. In 1926, Scott and Gross (7) of the U. S. Bureau of Mines con- ducted extensive research on the adsorption of gold and silver from cyanide leach solutions. Among their findings was the result that the most important factor in improving the adsorptive power of charcoal was heat treatment with oxidation by air or steam. The work of Zadra (8) in 1952 stimulated renewed interest in the use of activated charcoal in gold and silver recovery with the development of a method of recovery of the gold and silver from the charcoal other than its destruction by burning. The process involved simultaneous desorption

Jan 1, 1983

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.' The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

By Harold H. Haman

In view of Twentieth Century advances in mineral dressing technology, most modern metallurgists would be inclined to class jigging as an early, somewhat primitive, representation of their art. The practice of metallic sulfide concentration by jigging is becoming rare. This is so, in part, because the type of ore amenable to the process is becoming rare. It is appropriate, however, that this symposium recognize that a significant contribution of domestic zinc remains dependent upon coarse preconcentration by jigging, and that the state of the art be described even though the theory and applications are already well delineated in technical literature. One of the few areas still using jigging as a major concentrating process is The Upper Mississippi Valley. AREA HISTORY AND JIGGING The Upper Mississippi Valley (UMV) has produced one billion dollars worth of zinc and lead at current prices. The district includes the southwest part of Wisconsin, the northwest corner of Illinois and an adjoining narrow strip of Iowa. Within a total area of 4,000 square miles, important sub-districts cover about 400 square miles. As is widely known, early mining in this district involved shallow lead---crevice deposits of galena that were very selectively mined, hand sorted and cleaned, and then smelted at or near the site. The district has produced almost a million short tons of metallic lead, a very large part of this during the fifty- year period following 1830. Zinc mining began at the end of the civil war, but at a very low rate until about 1905.

Jan 1, 1970

By Frederic Dewey

IT IS common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no. real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when, arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupellation, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy1 says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 says that at a proper temperature no silver is lost by volatilization.

Jan 2, 1920

By J. G. Koenigsberger

The electrical specific resistance of rocks in the field is measured by sending a current through a medium of great volume, compared to the electrodes, whose resistivity should be measured. The whole resistance can be determined by the Wheatstone bridge and the specific resistance calculated by a well-known formula. The resistivity of some rocks in place in Germany and in Switzerland is given; first, of a rock near the surface, and especially near electrodes. Practical applications are made in the determination: (1) of the continuity of a conducting orebody; (2) of the surface ares of an orebody; (3) in the detection of a water-bearing fault in a salt mine. Preliminary 'observations are described: (1) on the influence of the depth of ground-water table; (2) on the detection of gas under high pressure in coal seams. The observations in this paper of the electrical resistivity of rocks and soil in place are along the lines of the very interesting method and results of the Messrs. Gish, Rooney, Hotchkiss and Fisher. 1,2 All the work described has been done since 1920. Method Used The very simple method consists in the application to the rock of two plane circular electrodes of iron or brass of a suitable diameter, with the aid of a contact substance, and in measuring the resistivity in a Wheatstone bridge with alternating current of 100 to 400 Hertz frequency per sec.). The general formula is known to be R= R0 +d/4(1/a+1/b-1.7/l+0.8(a+b)/l2) (1)

Jan 1, 1929

By R. E. Smallman, J. C. Terry

J. C. Terry and R. E. Smallman (Llniuersity of Birmingham, England)—In a recent publication53 Wood and Westbrook have reported the results of an investigation of the tensile behavior of fl-phase AgMg alloys. These results agree in broad outline, but differ in the details, with those obtained in the above laboratory and, consequently, some discussion of their paper would seem appropriate. In our experiments, tests were carried out on extruded wires, 2 mm diam, in a hard-beam tensile machine, and while an oil bath was used for the tests up to 150°C, above this temperature the oil bath gave rise to serious contamination of the specimens and hence tests above 150°C were made in vacuo. This procedure is different to that adopted by Wood and Westbrook. The ß-phase alloys exhibit differences in mechanical behavior when they are tested in different temperature ranges. In agreement with Wood and Westbrook, three characteristic ranges are observed which may be classified as low, intermediate, and high temperatures, respectively. Our experiments show that in the low-temperature region, the shape of the stress-strain curves is similar to that reported. However, in addition, it is observed that the temperature at which the low-temperature region ends is markedly dependent on strain rate, and increase with increasing strain rate as shown in Fig. 18. The temperature at which a transition from the low to the intermediate temperature takes place is about 0.4 to 0.45 of the absolute melting point, Tm. This transition temperature coincides with that at

Jan 1, 1963

By Charles H. Kline

Industrial minerals are the Cinderella of the mining I industry. Often considered as just dirt by traditional hard-rock miners and oil drillers, these products nonetheless comprise the second largest segment of the industry and the fastest-growing one. With annual sales of $5.7 billion, industrial minerals make up 22% of the dollar value of U.S. mineral consumption. By contrast, metals account for only 11%. Fuels, of course, are dominant, representing 67%. The dollar values of production and consumption for the three segments of the industry in 1968 are shown in Table I. The growth rate of industrial minerals is shown in Table II. From 1953-1968, the current-dollar value of all U.S. mineral production increased at the average annual rate of 3.8% while that of the gross national product increased at 5.9%. Industrial minerals are the only segment of the mining industry that approached the growth of the overall economy in this period, with production values increasing 5.1% a year and apparent-consumption values 5.6% These data, expressed in current dollars, include the effects of inflation. The growth in U.S. industrial minerals production is even more striking when expressed in indexes of physical production. As shown in Table III, production of all U.S. industries increased by 4.1% a year from 1953 to 1968. The growth in production of stone and earth minerals just matched this figure. By contrast, the average annual increase for oil and gas was 2.2%: for metals, 1.6% : and for coal, only 0.6 %.

Jan 1, 1970

By Henry G. Petrow, Edward S. Porter

MAJOR occurrences of lignite with significant uranium concentrations have been reported in western parts of the Dakotas, especially in Harding County, S.D., and Billings and Slope counties, N.D. Samples containing as much as 2 pct U3O8 were received at the Winchester Laboratory, but those deposits reportedly of major significance have generally contained 2 to 4 lb of uranium per ton of lignite. Most of the uranium appears to be associated with the carbon in the lignite as a urano-organic complex, although in most instances analysis of inorganic material has shown uranium values. Molybdenum is similarly associated with the carbon, and its concentrations generally parallel the uranium. The noncarboniferous material is mainly composed of gypsum, jarosite, bentonite, sandstone, and miscellaneous carbonates and silicates. The heating value of these lignites has been determined as about 3500 Btu on a dry lignite basis. The ash content of lignite has varied widely, the important samples containing 30 to 60 pct ash on a dry lignite basis. Because of the significant upgrading of uranium values obtained by ashing the lignite, and because recovery of uranium from raw lignite presented formidable processing problems, major emphasis at Winchester has been placed on devising methods to recover uranium from lignite calcines. Proper roasting removes the problem of organic fouling of solutions, reduces the size of the leaching plant for an equivalent uranium throughout, and generally provides equal or better acid leaching efficiency with less acid than can be obtained from the raw lignite.

Jan 9, 1957

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By R. L. Andelin, J. D. Knight, M. Kahn

Self-diffusion in single-crystal tungsten and diffusion of rhenium tracer in single-crystal tungsten have been measured over the temperature range 2660° to 3230°C by direct sectioning and radio-chemical analysis of W185 and Re183 and Re184 tracers. The initial radioactive layer was produced on the diffusion specimens by bombardment with 9.0-mev deuterons. Diffusion heating of the samples in high vacuum was accomplished by induction heating. Temperatures were measured by optical pyrometry, and the system was calibrated ALTHOUGH a considerable body of experimental information has been accumulated on self-diffusion in solids, the major part of the detailed work has by reference to the melting points of tantalum (2996°C), molybdenum (2620°C), niobium (2468°C), and rhodium (1966°C). The diffusion coefficients for the two systems, obtained by least-squares analyses of the data, are well-represented by the equations thus far dealt with relatively low-melting systems. Diffusion studies on the high-melting elements niobium,1 tantalum,2,3 and tungsten4'5 have been limited to polycrystalline material, for which data interpretation and theoretical analysis are sometimes difficult. Only recently, a study has been made with single-crystal molybdenum.6 The present work deals with the measurement of self-diffusion in single-crystal tungsten at temperatures approaching the melting point (3410°c).7 Since the method chosen for producing the radioactive tracer layer-bombardment with deuterons—produced detectable isotopes of rhenium as well as of tungsten, the diffusion of rhenium was measured also.

Jan 1, 1965

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,' from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

By J. Eldridge, K. L. Komarek

Activities of aluminum in solid Fe-Al alloys have been determined between 0 and 75 at, pct Al and 1100" and 1400°K by an isopiestic method in which iron specimens, heated in a temperature gradient, are equilibrated in a closed all-ceramic system with aluminum vapor. The activity of aluminum in these alloys shows a strong negative deviation from Raoult's law at low concentrations but increases rapidly above 40 at. pct Al. The enthalpy and entropy of mixing me both negative. For an alloy with equiatomic composition the values are: HM = -7300 cal and SM = -0.85 eu. Sodium chloride has been added at lower temperatures to accelerate the evaporation of aluminum. Equations have been derived to calculate activities of aluminum from experimental data. THE Fe-Al system has been the object of a great number of investigations.' Most of these studies have been concerned with the phase diagram and specifically with the order-disorder reactions in the range of solid solutions of aluminum in iron. The results have been compiled by Hansen2 and presented as a complete phase diagram, Fig. 1. More recently, Taylor and ones' have found that both ordered and disordered alloys can exist in the a field up to the solidus curve separated by a line starting at 18.75 at. pct Al at room temperature up to 37 at. pct Al at 1375°C. Chipman and coworkers4-7 have studied repeatedly the activity of aluminum in liquid dilute Fe-Al alloys. They have measured the distribution equilibrium of aluminum between liquid iron and

Jan 1, 1964

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep upper- most the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance: 1.Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1951

By J. D. Shaw, E. B. Gebert, D. O. Noel

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By D. O. Noel, E. B. Gebert, J. D. Shaw

IT. is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of. manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics .that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. MACHINING Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By D. O. Noel, E. B. Gebert, J. D. Shaw

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By Roy Moore

THE Tom Reed Extension and Big Jim mines of United Eastern Mining Co. are situated in the Oatman district, Mohave County, Ariz., about 28 miles southwest of Kingman, the nearest railway point. Articles descriptive of the mine surface plant, mill construction, and plant operations have been written by Otto Wartenweiler1, the designing engineer; Wheeler 0. North,2 when he was assistant general manager for the company, and Earle M. Bagley, mill superintendent.3 The last article covers average costs for the full time the mill was operated. The geology of the mines is described by F. L. Ransome4 of the United States Geological Survey. Production was started in January,. 1917, and the known orebodies were exhausted in May, 1925, showing a life of seven years and five months. On account of the comparatively short life and the fact that stoping operations were confined to two orebodies, little experimenting was done with mining methods. The two orebodies were in what is generally called the Tom Reed-United Eastern vein, which occupies a fault fissure having a normal displacement of several hundred feet. Seven or eight very productive ore shoots were mined along this vein in a distance of 1 ½ miles, the two worked by the United Eastern being 1 mile apart. The maximum dimensions of the Tom Reed Extension ore shoot were height, 750. ft.; length, 950 ft.; thickness, 48 ft. The vein structure varied from a solid quartz-calcite filling to a series of parallel stringers separated by andesite. From this body, 511,976 tons of ore were mined. (Fig. 1.)

Jan 1, 1928

By MARIUS R. CIMPBELL, Edward W. Parker

DESCRIPTION. ACCORDING to the estimates prepared by the U. S. Geological Survey, the area underlain by workable coal-beds in the United States is 496,776 sq. miles. Of this total area, 480 sq. miles contain the entire anthracite coal-fields of Pennsylvania. The bituminous coal-fields are estimated to be contained in areas aggregating 250,051 sq. miles. The grade of coal between bituminous and lignite, and which is designated by the Geological Survey as " sub-bituminous," is estimated to be contained within areas aggregating 97,636 sq. miles, while the areas containing lignite aggregate 148,609 sq. miles. The coal-fields are divided, for the sake of convenience in classification, into six main provinces, as follows: 1. The Eastern. Province, containing the anthracite coal-fields of Pennsylvania and the bituminous coal-fields of the Appalachian region-namely, those of western Pennsylvania, Ohio, Virginia, West Virginia, Kentucky, Tennessee, Georgia, Alabama, and small outlying areas in North Carolina. 2. The Interior .Province, containing the bituminous coal-producing regions of Michigan, Illinois, Indiana, western Kentucky, Iowa, Kansas, Missouri, Oklahoma, Arkansas, and Texas. 3. The Gulf Province, containing the lignite-areas of Alabama, Mississippi, Louisiana, Arkansas, and Texas. 4. The Northern or Great Plains Province, containing the lignite and sub-bituminous areas of North and South Dakota, eastern Montana, and northeastern Wyoming. 5. The Rocky Mountain Province, containing the bituminous and sub-bituminous areas of western Montana and western Wyoming, Colorado, Utah, and New Mexico. 6. The Pacific Coast Province, containing-the areas of Washington, Oregon, and California.

Apr 1, 1909