Search Documents

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By Seymour G. Epstein

Using a modified capillary-reservoir technique, electromigration of dilute solutions of silver in liquid bismuth has been measured with relatively good precision. The effects of experiment duration, temperature. current density, and silver concentration have been investigated. Chemical diffusion coefficients of silver in liquid bismuth were also measured at temperatures ranging from 300°to 600°C. The effective valence of silver in bismuth was calculated as a function of temperature from a comparison of electric mobilities and diffusion coefficients. In an alloy containing 1 wt pct Ag, the electric mobility of silver increased from 1.65 x X sq cm per v-sec at 300°C to 2.38 x 10-4at 600°C; the diffusion coefficient in-creased from 3.0 to 17.5 x 10-5 sq cm per sec over the same temperature range. Calculated values of effective valence decreased from 0.28 at 300°C to 0.10 at 600°c. ALTHOUGH there has been considerable progress in the theoretical treatment of electron-transport properties in liquid metals, the mechanisms of mass-transport phenomena in liquid metals are still not clearly understood. This is especially true for the case of electro migration, alternatively termed elec-trotransport or electrodiffusion, which is mass transport induced by an applied electric field. A thorough knowledge of the mechanisms governing electromigration will considerably aid in understanding the electronic state of an impurity atom in a liquid metal. Electromigration has been long observed and studied in liquid metals and alloys. However, no satisfactory theory to explain the observed effects has been developed. The disparity in the present theoretical treatments, summarized by Verhoeven,1 has been attributed to the difficulty in describing the momentum transfer between electrons and ions and to the lack of precise measurements in liquid metals, especially at elevated temperatures. Prior to the last decade most of the electromigration studies were qualitative, in that only the direction of migration of alloy constituents was determined with any degree of reliability. These results have been summarized by schwarz,2 who was able to measure the electric mobility of several elements in mercury. More recently electromigration in liquid metals has been measured by a variety of techniques, with a varying degree of success. Mangelsdorf3,4 made precise measurements on dilute amalgams at room temperature, using a technique relating changes in composition to changes in alloy resistivity, but was unable to make measurements at elevated temperatures. Using a modification of this technique, Verhoeven and Hucke5 measured electromigration and resistivities in liquid Bi-Sn alloys. However, the resistivity technique is not sensitive to small composition changes and is impractical for very dilute alloys. Verhoeven and Hucke6 also measured electromigration of several solutes in liquid bismuth by adapting the capillary-reservoir method for determining diffusion coefficients in liquids. The reported precision of these measurements was poor, however, primarily due to the large uncertainties in the chemical analyses to determine concentration changes. Belashchenko7 has summarized the recent Russian investigations of electromigration, many of which, however, are of questionable accuracy. The present study was initiated to develop an experimental technique which would be both versatile and sufficiently sensitive to yield precise measurements of electromigration of solutes in dilute metal alloys at elevated temperatures. Using this technique, a comprehensive study of silver in liquid bismuth was made to determine the effects of experimental variables on the apparent electric mobilities. Chemical diffusion coefficients of silver in liquid bismuth were also measured over the same temperature range for comparison with the electromigration data. EXPERIMENTAL TECHNIQUE Electromigration Measurements. Electromigration of silver in liquid bismuth was measured by the capillary-reservoir technique, similar to that used by Verhoeven and Hucke,6 but modified to yield more

Jan 1, 1967

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:',' oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.' Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By Edwin B. Wilson, Joseph W. Leonard, Richard W. Borio

preparation of specification coals for the utility industry is approached from the standpoint of a cooperative effort with the power company to assure that the shipped product will be a noncorrosive coal. Selective mining, coal preparation, the use of additives, and coal blending are mine-site techniques proposed as means for upgrading corrosion-retarding constituents of utility coals (CaO and MgO) while, at the same time, reducing the concentration of those constituents of coal (Na20 and K,O) which cause corrosion. Data obtained from large-scale boiler testing in combination with bench-scale physical and chemical tests are used as a basis for the formulation of mine-site procedures to improve coal combustion utilization. Electric power generation remains the greatest market for coal in the United States. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F. In addition to causing power outages and high maintenance costs, corrosion is a continuing barrier to the future development of more efficient steam cycles which permit lower generation costs when using coal. Research methods of the past which have been directed at finding solutions which could be applied at the power plant site have been only partially successful and are generally costly. This paper contains a suggested --method of corrosion control through investigation of the problem at the source of the trouble—the coal supplier facility. It is proposed that mine-site pre-ventative procedures be considered as an effective means of cooperative corrosion control between the power company and the coal supplier. Economic justification must be applied to the individual situation. This paper is based on recent work by Combustion Engineering, Inc. and the Coal Research Bureau of West Virginia University under a contract from the Department of the Interior Office of Coal Research.',' Results which are of importance to this discussion may be summarized as follows: 1) The alkali minerals of coal (Na2O and K2O), as measured by an acid leaching process, can be related to corrosion rate in utility boilers. As these constituents increase in a coal product, its corrosiveness can be expected to worsen. 2) The alkaline-earth minerals contained in coal, reported as total CaO and MgO reduce corrosiveness 2s their concentration increases. 3) Naturally occuring, alkaline-earth-bearing materials, such as limestone and dolomite, may be added to a coal to reduce its corrosiveness. 4) Coals with very low iron contents tend to be less corrosive. These results provide the groundwork for examination of the system of operations which occur at the supplier facility from the seam face where mining is begun to the point of loading for shipment. The Mining System Fig. 1 is a cross section of one of the typical coal seams (designated coal A) that was boiler tested during this research program. This seam is overlain by material which consists primarily of a gray-black shale. In the lower third of this seam, there exists a thin rock parting of less than 4 in. in thickness which is consistent throughout the seam. The floor material is fireclay. In order to examine mineral distribution throughout this particular seam, the Coal Research Bureau collected a

Jan 1, 1971

By John Wulff, David A. Stevenson

The solubility of iron and cobalt in liquid lead, the solubility of chromium in liquid tin, and nickel in liquid silver were determined up to 1300°C in an atmosphere of hydrogen. Liquid samples were taken at different temperatures and analyzed. The data obtained were plotted to show the relationship between log mole fraction of solute and the inverse of the absolute temperature. Resulting values for the differential heat of solution (AH) and the excesspartial molar entropy (S)are: for the iron-lead system = _24,200 cal per mole and AT = 5.0 e.u. for the a phase, and AH = 18,300 and S = -0.1 e.u. for the y phase; for the cobalt-lead system AH = 16,500 cal per mole and AS =0.7 e.u.; for the chromium-tin system AH = 15,600 cal per mole and AS = 8.5 e.u.; for the nickel-silver system AH =18,000 cal per mole and AS = 4.0 e.u. RECENT developments in coating, brazing, and heat transfer have focused attention on specific cases of solid-liquid interaction in metal systems, particularly those involving dilute liquid solutions. One fundamental quantity of interest in such systems is the equilibrium phase distribution between solid and liquid phases. In any effort to fully understand such interactions, one must be able to describe the equilibrium state precisely. Furthermore, in order to develop genera! relations for such systems, one must know the equilibrium state in a number of different cases. This investigation was devoted to a study of the equilibrium phase distribution in four binary systems: solid iron-liquid lead; solid cobalt-liquid lead; solid chromium-liquid tin; solid nickel-liquid silver. The iron-lead system was previously studied by Shepard and parkman' and later by Fleischer and Elliott2 with differing results. Both investigations were carried out by sampling the saturated liquid, and analyzing it chemically. The cobalt-lead system was previously reported by Pelzel,3 who noticed no discontinuity near the transformation. A limited investigation of the chromium-tin system was made by Wlodek and wulff4 using a weight loss method. This work was done in conjunction with the development of a process for coating molybdenum with chromium from tin solutions. To more fully under- stand the kinetics of the process, a more accurate determination of a solubility was desirable. No significant data were found in the literature on the nickel-silver system. Data on the latter system were, however, relevant to the investigation of the corrosion kinetics of copper-nickel alloys in liquid silver as carried out by Harrison and wagner,5 EXPERIMENTAL APPARATUS AND PROCEDURE Of the techniques available for the study of such systems the most effective appears to be that of liquid sampling,2,6,7 which is the method used in the present investigation. A schematic diagram of the sampling furnace is given in Fig. 1. Large pieces of solute metal, in excess of saturation solubility, were added to 200 g of the solvent metal, and the entire charge placed in an alundum crucible. Analytical reagent or materials of chemically pure grade were used in all investigations. The crucible was contained in a zircon muffle tube positioned vertically in the uniform hot zone of a Globar resistance furnace. The tube was provided with a number of ports which permitted sampling at temperature and in controlled atmospheres or vacuum; the ports were also useful for evacuation and introduction of gases as well as for thermocouple measurements. A chromel-alumel thermocouple Sheated in a porcelain tube was used for temperature measurements. A purified hydrogen atmosphere was employed in all experiments reported in this paper. The hydrogen was purified by passing it first over hot copper gauze to remove oxygen and then through a molecular sieve immersed in

Jan 1, 1962

By C. R. Kyle, R. L. Perrine

A transparent model of a reservoir has been used to study some characteristics of instability in miscible displacement. The linear model dimensions are 1/4 in. x 91/2 in. x 10 ft. The model is packed with spherical glass beads. Thee groups of experiments have been performed. The objectives were to measure, respectively, the rate of growth of the transition zone, flow velocity variations in the transition zone, and the effect of a graded viscosity zone on stability. All experiments were compared, where possible, with theory. The transition zone grew almost linearly with distance traveled, regardless of flow rate, where adverse viscosity ratios were used. At very adverse viscosity ratios and large distances traveled, some reduction below linear growth was noted. This could be attributed to the effects of mixing. General similarity in flow pattern was commonly shown in different tests, although exceptions occurred at the higher viscosity ratios. Injection of tracer spots permitted direct experimental measurement of velocity variations. Statistical methods were used to compare observed velocity variations with recently published theories. Surprisingly good agreement with some theoretical predictions was obtained. In the experiments using an initially graded viscosity zone, macroscopic stability was reached before predicted by theory. Under conditions theoretically considered to be slightly unstable, any fingering tendency was too slight to become observable within a 10-ft long system. The general correlation of all experiments with published theory was good, and suggests that theoretical predictions can be extended to reservoir problems. INTRODUCTION Early laboratory studies of miscible displacement demonstrated the high recovery efficiency possible with this method. Linear laboratory models showed that, under some circumstances, all in-place hydrocarbons could be recovered using as little solvent as 5 per cent of the pore volume. These results led to a series of pilot field projects. Under realistic conditions, however, other laboratory studies showed that a small solvent bank may not recover much more oil than a conventional gas drive. The cause of this lack of efficiency is unstable viscous fingering. The size of the solvent bank required to give optimum recovery is, therefore, a question of great economic significance. The object of the experiments described in this paper was the quantitative measurement of unstable flow parameters, the verification of present theories on the miscible displacement process, and correlation of these theories with ex peri mental observation. Of the theories which have been advanced, those by Dougherty, Koval and Perrine show promise of predicting reservoir performance with reasonable accuracy.l-7 The present experiments were correlated, where possible, with the theories of Koval and Perrine. Dougherty's theory was not used because of the additional computational difficulty it presented and the belief that no further information would result. EXPERIMENTAL EQUIPMENT A transparent reservoir model, consisting of a vertical reinforced plexiglass column, was used for the experiments. The column was packed with glass beads, which served as the porous medium. To induce a known velocity disturbance in the flow, a double cosine wave restriction in the transverse cross-section was placed at the top of the column. To mark the flow field and provide a means of measuring the local fluid velocity, a dye-spot injection system was provided. The column was 10 ft high by 1/2 in. wide by 1/4 in. deep. The cosine restriction was placed 16 in. from the top of the column. The glass beads were smooth and spherical and had a mean diameter of 0.0102 cm. Liquids entered the top of the column through a manifold allowing three points of entry (left, center, and right, or any combination of these). A positive-displacement pump with variable-speed drive was used to control liquid flow rates. The pump transferred viscous oil from a reservoir to an accumulator, which displaced the test liquid into

Jan 1, 1966

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By William C. Hagel

Oxygen-18 exchange between gaseous oxygen, held at a pressure of 125 mm Hg in a PL-IORh chamber, and splzeres of a Fe2O3 containing three or less grains was determined from 9000 to 1250°C. Isotope equilibrum on crystal surfaces appears to be quickly established, and the rate-determining factor is self-difiusion confbvrning to the relation D = 2.04 esp(- 77,900/RT) sq cin sec-'. Changing sphere diameters caused no detectable variation in diffusion coefficients. Oxygen ions diffuse faster than cations at low temperatures, but a crossover may occur at about 1150°C. INVESTIGATIONS by Davies et al.' and Himmel et al2 have suggested that the mechanism of iron oxidation above 600°C involves a predominance of cation migration in the wüstite (FeO) and magnetite (Fe301) layers and oxygen-ion migration in the hematite (a Fe2O3) layer. Evidence for little cation migration during hematite growth consists of: 1) the disappearance of radioactive-silver markers, presumed to vaporize from the oxide-gas interface, and 2) a large discrepancy between parabolic rate constants for magnetite oxidation and those calculated from Lindner's3 data for cation self-diffusion, D:, using Wagner's theory.4 Reversing the calculations gave anticipated self-diffusion coefficients, D:, for oxygen ions of 3.6 x 10-9 sq cm sec-1 at 1100°C and 5.9 x 10-10 sq cm sec-1 at 1000°C. Since then Kingery et a1.5 reported three values for oxygen-ion diffusion in polycrystalline, sintered hematite. These were obtained near 1200°C, at an oxygen pressure of approximately 150 mm Hg, and could be represented by the Arrhenius expression, Dg = 1 x 10 11 exp(-146,000/RT) sq cm sec-1. Extrapolation to temperatures below 1100°C infers that oxygen ions are less mobile than cations. This contradicts the aforementioned oxidation evidence and also coble7s study of the initial sintering of hematite. From the latter, apparent diffusion coefficients for the slowest rate-controlling species could be calculated, and fair agreement was found with an extension of Lindner's data for cation diffusion. Fig. 1 depicts such comparisons graphically. Three points have been included for the determinations of Himmel et al. on cation diffusion in large, natural hematite crystals surrounded by pure oxygen at atmospheric pressure. No dependence on crystal log raphic direction was noted. Since the value of 10-l4 sq cm sec-' at 1000°C actually represents an upper limit, one might interpret that there is a small decrease in D: when single crystals are employed. On the whole, however, cation diffusion appears relatively well-defined,* while the few results tension to lower temperatures. After having gained experience measuring oxygen-ion diffusion in certain glasses7 and in the corundum oxide, a Cr2O3, the purpose of this work was to determine D; values for hematite and thus possibly assist a mechanistic understanding of the kinetics of the oxidation and reduction of solid iron oxides. I) EXPERIMENTAL PROCEDURE A) Material. Hematite powder of moderately high purity was received from the Columbian Carbon Co. An accompanying lot analysis listed 0.03 H2O, 0.008 weight percents, with the remainder Fe2O3. Subsequent treatments were ball milling, drying, prepressing, and hot-pressing for 60 min at 1350°C under 5000 psi. Since graphite dies coated with a slurry of alumina were used for hot-pressing, the surrounding atmosphere at temperature was sufficiently reducing to form some magnetite on the outer surface of each cylinder. After removing any attached alumina, a stabilizing anneal of 50 hr at 1300°C in oxygen was added. The final product was nonmagnetic and exceeded 97 pct of the density (5.24 g cm-3) usually given for FezO3. On polishing cylindrical ends, counts were made of the number of grain boundary intercepts per

Jan 1, 1967

By H. L. Overton, J. B. Lipson

The concept of sodium single-ion equivalent activity as developed by Gondouin, Tixier and Simard,' was used to determine the filtrate resistivity-activity relationships for 150 laboratory and 49 field drilling muds. With the exception of the native and phosphate high-resistivity muds and the calcium-treated muds, the filtrate resistivity-activity relationships were found to be within 20 per cent of that for pure sodium-chloride solutions. Gondouin, et al,* previously suggested a method of treating the high-resistivity muds in quantitative electrical log analysis. A new treatment is presented which uses the P-alkalinity of the filtrate as a correlating parameter in handling the calcium-treated muds in quantitative electrical log analysis. INTRODUCTION Gondouin, Tixier, and Simard in 1957 introduced new interpretive procedures for analyzing the self-potential curve of electric logging. They re-emphasized the previous work of the Schlumberger brothers, Wyllie and others, and re-defined the activity concept in terms of a number which they termed the effective resistivity. Their procedures are particuarly effective when the connate-water resistivities are less than 0.08 ohm-m or greater than 0.3 ohm-m. For gyp muds where the calcium content is known, a procedure was presented which allows calculation of the connate-water resistivity with improved accuracy. These procedures assume that one of the fluids in the system is a pure sodium-chloride solution, but they are not limited by the assumptions. For the fresh and saline connate waters, for instance, it is assumed that the drilling mud filtrate is a pure sodium-chloride solution. For the gyp mud interpretive procedure, it is assumed that the connate water is a pure sodium-chloride solution. Brown,' on the other hand, has suggested that it would be extremely fortuitous if drilling mud filtrates could all be treated electrochemically as sodium-chloride solutions, and he cites some examples where discrepancies exist. A study has been made of the deviations of sodium single-ion equivalent activities, an of drilling mud filtrates from that of pure sodium-chloride solutions. Drilling fluids in common use on the Texas and Louisiana Gulf Coast and laboratory-controlled muds were investigated. Using a cell patterned after Gondouin, et al, (Fig. I), the equivalent activities were measured. It should be remembered here that the activity measured is merely an index which uses numbers that represent the sodium single-ion equivalent activity a,., of the mud filtrate. The membrane potential developed across the cell was determined with a null-type potentiometer. The resistivities of the solutions were measured by the four-electrode method. The resistivity system was calibrated by using saturated KC1 solution as a standard. Chemical properties of the drilling fluids studied were measured with standard API-approved equipment for the particular property in question. For the activity measurements, two shale discs were chosen to serve as cationic membranes. These two discs were both 1 1/4 in. in diameter and, respectively, 1/4 and 1/8 in. in thickness. The membrane potential, Em, was determined using the shale discs as cationic selective membranes separating two standard sodium-chloride solutions of known mean activity. Then by comparing the constant Km in the following equation, with the theoretical value of — 59 mv at 75OF, the perfection of the membrane was determined. The variation of Km for the two membranes used in this experimental work, as well as one of the many unsuitable membranes, is shown in Fig. 2. The measurement of the activity of mud filtrate involves the balancing of its combined individual activities against a standard solution of known mean activity. At the point where there exists zero potential across the membrane cell, the activity effects may be assumed equal for all practical purposes. The mechanics of making a null reading of this sort requires having a large number of different mean activity solutions. A more practical method involves

By Lawrence A. Shepard, Richard H. Krock

A series of ductile, two phase W-Ni-Fe composites, sintered in the presence of a liquid phase, were tested in tension. Identical room temperature stress-strain curves were obtained for specimens containing from 80 to 92 wt pct W (58 to 75 vol pct W particles). The composites exhibited a maximum elongation of 29pct at room temperature, and 10.7 pct at 77 °K. The tungsten particles in the composite elongated by the same amount at these temperatures. Single-phase alloy specimens matching the composition of the composite matrix showed about one half the flow stress of the composites. The test results demonstrated that the mechanical properties of W-Ni-Fe composites are determined by the tungsten particles alone and are independent of matrix volume fraction or mean free path over the composition range studied. A general prediction of the plastic behavior of two-phase alloys or composites from a knowledge of the properties, size, shape, and dispersion of the individual components is not, at present, possible. The excellent theoretical and experimental exposition of the dispersion-strengthening problem applies only to cases where the stronger phase is present as fine particles and in volume fractions of a few percent. Materials in which the stronger phase constitutes a significant fraction of the volume, although of broad engineering interest, have received comparatively little analytical attention. This important group of materials is the concern of the present study. The degree of deformation of each phase during the plastic working of a ductile two-phase alloy has been established by Boas and Honeycombe,1 Clare-brough,2 and Clarebrough and berger.3 These workers empirically correlated the recrystallization temperature of the individual phases with the degree of cold work sustained by each. It was shown that the deformations of both phases are equal and therefore the same as that sustained by the composite whole when the volume fraction of the stronger phase exceeds 35 pct. At yielding, however, deformation begins in the weaker phase. A direct correlation of composite strength, as a function of deformation, with the strength of the individual components cannot be made. In the presence of stronger phase particles, the flow stress of the weaker matrix phase is enhanced by an additional hydrostatic component. The development and potential magnitude of matrix strength promotion upon straining has not even been experimentally established. Quantitative work in this field has been confined to ceramic-metal composites. These materials fracture at strains considerably below 1 pct by cracking of the ceramic particles.4-6 An indication of the potential constrained matrix strength capacity is given by the observation by Nishimatsu and Gur-land4 that the maximum tensile strength of a WC-Co composite is almost double the bulk strength of the cobalt matrix. The relationship between composite strength and geometry is ordinarily expressed in terms of the mean-free matrix path (referred to subsequently as MFP) between the stronger particles.* This factor takes into account both the volume fraction of matrix phase and the average size of the particles. unke17 concluded that composite strength varied directly with the decreasing log MFP, following the Gen-samer8 relationship. However, Gurland and ~radzil~ reported a strength maximum at an MFP of the order of 1 p in WC-Co composites. A ductile two phase metallic composite was chosen for the present investigation of composite mechanical properties with the view of avoiding the difficulties and ambiguities noted above. The W-Ni-Fe heavy alloy of Green, Jones, and pitkin9 contains 80 to 94 wt pct W, and nickel and iron in a weight ratio

Jan 1, 1963

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß'. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß' which in turn form the Widmanstatten a in ß'. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.' There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence'..' in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"' ' report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By C. W. Covington, H. C. Cook, J. F. Libsch

Sputtered aluminum thin films were prepared in each of two conventional bell-jar vacuum systems. One system utilized an inner "getter sputtering" enclosure; the second system was a standard diode sputterirlg arrangement. Consistent and repeatable film properties were obtained in both systems provided sufficient cleanup and presputter time was allowed. The various problems associated with aluminum sputtering are discussed, with pavticular attention to the vzinimization of film contamination by outgassing and oxidation. The growth and structure of the aluminum thin films were studied with the aid of electron wzicroscopy and related to deposition rate, substrate temperature, and film thickness. The resistivity of the films was correlated to film structure and surface roughness. Resistiuities as low as 3.5 microhm-cm (2.3 x bulk resistiuity) were measured for relatively thick films (20,000). THIS investigation was undertaken to explore the problems and film characteristics associated with the sputtering of aluminum. Earlier work reported on aluminum sputtering has stressed the contamination of both the cathode and film as well as abnormally low deposition rates.' Data on sputtering yields,3 however, indicate that aluminum sputtering could be practical. Recently, it was shown by Theuerer and Hauser3 that aluminum sputtering was feasible in a conventional oil-diffusion pumped vacuum system provided an inner "getter sputtering" enclosure was employed to minimize gaseous contamination. This technique employs the getter action of aluminum to produce extremely low reactive gas partial pressures in the deposition zone. Aluminum films have already found use in solid-state electronic devices such as transistors and integrated microcircuits. To the present time, most aluminum films have been prepared by evaporation due to the ease with which this metal can be evaporated. Controlled sputtering of aluminum offers a number of advantages over evaporation, however, such as 1) manufacturing compatibility with other metals which must be sputtered, 2) better control of process variables resulting in more repeatable and uniform films, 3) generally better adhesion resulting from higher-energy metal atoms, 4) built-in material supply for continuous operation, and 5) the ability to deposit alloys. The data presented in this paper are the result of two separate studies. One study utilized a small "getter sputtering" enclosure (System A) and was concerned with the structure and properties of thin aluminum films up to about 1600A thick. In this thickness range, study of the film structure was possible with transmission electron microscopy. The second study was conducted with a conventional diode sputtering apparatus (System B) and covered $ much wider range of film thickness up to about 34,000A. Emphasis was placed on developing techniques which would extend aluminum sputtering to an existing in-line continuous deposition process.4 I) EQUIPMENT AND PROCEDURE System A. Fig. 1 shows a schematic of the "getter sputtering" inner chamber used and Fig. 2 is a photograph of this chamber mounted on an 18-in. access ring of a standard liquid-nitrogen trapped bell-jar vacuum system. This chamber was designed after a similar system used by Theuerer and auser.3 The configuration allowed the glow to emanate in all directions from the cathode. Argon (99.99') was allowed to enter only at the top of the chamber such that most of the reactive gases entering with the argon were reacted with the aluminum vapor and deposited on the chilled walls of the chamber before reaching the deposition zone. Provision was also made as shown, Fig. 1, for heating and cooling the substrate from about 20" to 400°C. Two substrate materials were used: Corning 7059 glass (12 by 12 by 0.048 in.) and carbon films about

Jan 1, 1967

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962