Search Documents

By Herman Van Fleet, Frederick W. Neil, O&apos

The object of this paper is to describe the present status and possil~ilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. 3. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Kitherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 1, 1927

By S. H. Gelles

Samples of poly crystalline zinc of 99.999+ pct purity were observed metallographically after having been exposed to hydrostatic pressures of up to 27 kbars. The deforrnation produced by this treatment was analyzed using X-ray and metallogaphic techniques. Basal-plane slip occurred universally in all grains exumined at the lowest pressure used (8 kbars). At pressures of >23 kbars, {1012} twin nucleation and growth were noted as well as slip. Formation of bend planes, complex kink bands, and recrystallization at the gain boundaries were also observed in this pressure range. These observations are discussed in reference to the expected deformation behavior of zinc under high hydrostatic pressure. It has been shown over the past few years1'3 that anisotropic, poly crystalline metals can be made to deform plastically by the application of a hydrostatic pressure. The effect is greater 1) the larger the anisotropy of linear compressibility and 2) the smaller the stress level needed to produce plastic deformation. Zinc having both very anisotropic linear compressibilities and a very low critical resolved shear stress (CRSS) for basal-plane slip has been shown to exhibit large amounts of plastic deformation when subjected to a hydrostatic pressure.2,3 At pressures up to 15 kbars, grain boundary migration and slip on one set of glide planes have been reported.' After exposing samples to 20 kbars pressure, grain boundary migration, single slip, multiple slip, and twinning have been noted.' The identification of the deformation modes operative under these conditions has not been reported. It was the purpose of this research to identify the deformation modes induced in poly crystal line zinc by the action of a hydrostatic stress and to study the strain accommodation at grain boundaries. Hydrostatic pressure could affect the operational modes of deformation by altering the Peierls-Nabarro stress. This may be roughly approximated by the relationship4

Jan 1, 1967

By John L. JR. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Since the beginning of the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.' Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally the measurements are made systematically along the whole length of the open hole. The physical factors , or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1934

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By John L. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product ; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are: 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By C. Altstetter, Y. Huang, E. de Lamotte

Nitrogen was introduced into pure niobium (colutn-bium) and dilute Nb- Zr alloy wires by equilibration with pure nitrogen gas at high temperatures. Room-temperature hardness was correlated with the alloy composition, heat treatment, and microstructure. Hardness was found to be most sensitive to the amount of nitrogen in solution; however, a significant hardening up to 500 Dph look place upon aging of quenched alloys. A coarse dispersion of nitride did not significantly increase the hardness of the material though the nitride was found to have a hardness of 1400 Khn. BY now the marked effect of nitrogen on the properties of bcc refractorv metals is we ll-documented. There are few studies, however, in which the state of the solute has been carefully controlled. Indeed, the composition-temperature-pressure relationships in nitrogen-refractory metal systems have been determined precisely for only niobium and tantalum.'-4 Most investigations on niobium have dealt with alloys High-nitrogen alloys cleaved on (100) planes and had negligible ductility. Precipitation was found to occur in either a discontinuous or a continuous fashion, depending on the composition and cooling rates. Upon cooling, the precipitation first proceeded discontinu-ously by the nucleation of nilride needles at subbound-aries and subsequent growth of a two-phase microcon-stituent. At lower temperatures continuous precipitation occurred in the subgrain interior ahead of the discontinuous precipitation interface. containing nitrogen, carbon, and oxygen in significant but uncontrolled and, in several instances, undetermined amounts. Thus, there has been some uncertainty regarding the presence and the distribution of precipitates. This paper presents results which relate the hardness and microstructure to the heat treatment and nitrogen content of niobium and Nb-Zr alloys. Niobium rod* produced by the Wah Chang Corp.

Jan 1, 1968

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C.A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By C. A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By M. R. Pickus

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystalliza-tion has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers,6 were of a. qualitative nature. It is our hope that the present investigation may contribute some-thing to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939