Search Documents

By H. Margolin, E. Ence

In order to understand the effect of zirconium on properties of Ti-Cu-A1 alloys, Ti-Zr alloys were examined for the presence of ordering or compounds at the following compositions in weight percent: 24.1 pct Zr (lZr:GTi), 32.2 pct Zr (lZr:4Ti), 38.8 pct Zr (lZr:3Ti), 49.0 pct Zr(1Zr:ZTi). Alloys were prepared as 15-g buttons by non- consumable arc melting under argon atmosphere from Bureau of Mines titanium (Bhn 63) and Reactor Grade zirconium (Bhn 150). Weight losses during melting did not exceed 1 pct of the initial button weight. Prior to heat treatment, buttons were hot-rolled at 600" to 700°C to rods of about 6 mm diam. Contamination after hot-rolling was found to extend to a depth of less than 0.5 mm. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. Annealing times were as follows: 700°C — 7 days; 600°C— 14 days; 575°C-1 and 2 months; 525°C-2 months; 500°C-2 months. Prior to heat treatment, all Ti-Zr alloys were vacuum annealed at 900°C to remove hydrogen. The reanneal of 575°C specimens for an additional month produced no observable microstructure changes. The results obtained by microstructure and X-ray diffraction are shown in Fig. 1, together with data of Hayes et al.' No other phases than a or P were found. Small amounts of retained P were detected by X-ray in the 49 pct Zr alloy. The data of the present investigation suggests that ß and a transus boundaries are at considerably lower temperatures than those of Hayes et al. The work of Hayes et al. is based on sponge titanium and Bureau of Mines zirconium, both of which contained 0.15 pct 0. Since melting was performed in

Jan 1, 1962

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By John Blizard, Ralph A. Sherman

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

The early records of coal in Kentucky by Walker and Gist have already been mentioned. Thomas Hutchins was aware of it in 1778, or perhaps several years earlier, as in writing of the Buffaloe, now Green, River, he said, "several persons who have ascended this River, say, that Salt Springs, Coal, Lime and Free Stone etc. are to be found in a variety of places."1 The next record found is an entry to Ellis and Marshall, of 878 acres on Coal Bank Creek, in the, then Fayette County on July 14, 1784.2 The settlement might have been made, or the name given, some time before. Hermeline, in 1783, mentioned iron ore and coal on the Green River,' although he had not been west of the Susquehanna River; his knowledge of coal might have come from Hutchins, although the latter made no mention of iron in that locality. In November 1790, coal was mined on Sturgeon's Creek in Lee County and floated in three barges down the Kentucky River to Cleveland's Ferry, where it was hauled to Lexington. The results were not equal to the expectations, and it was 1793 before the experiment was. repeated 4 In 1791, the estate of Samuel Wharton advertised for sale 31,000 acres "in the county of Jefferson, on the North Side of the Green or Buffaloe river, in the State of Virginia."5 In November 1795 three patents were issued for land in the then Lee County, aggregating 130,000 acres. These patents cover much of Harlan County. The descriptions of these surveys mention passing stone coal. on Rough Branch of Martin's Fork, a "great deal of stone coal" on Blacksnake Branch of Pucketts Creek, and "a quantity of stone coal" probably on Crummies Creek.6 Jedediah Morse, in The American Gazetteer, 1798, said that in Kentucky "in many places there are appearances of potter's clay, and coal in abundance." It is possible that shipments may have been made from near

Jan 1, 1942

By W. W. Gerberich, P. L. Hemmings, V. F. Zackay

ThE strain-induced martensitic transformation may be used to attain desirable combinations of strength, ductility, and fracture toughness. One of the parameters is the relative stability of the austenite. For example, it has been shown by Zackay et al.1 that the volume percent of strain-induced martensite is related to the combination of strength and elongation obtained. It has also been shown that the degree of transformation is an important factor in the crack propagation resistance of metastable austenitic steels.2 Considering both tensile and crack-propagation tests, it was of interest to see if there was any functional relationship between the amount of strain and the volume of strain-induced martensite. Previously,9 it had been shown that at room temperature, there was a relationship between uniaxial tensile strain and the volume percent of resulting martensite given by The data were obtained by plastically elongating tensile samples to a certain strain and then measuring the field strength to determine the strain-induced ferromagnetic volume. This was accomplished for two conditions having yield strengths of 229 and 233 ksi. The nominal composition of this material was 9Cr-8 Ni-3 Mo-2 Mn-2 Si-0.25 C-0.09 N. In evaluation of the strain-induced martensite at a crack tip: the question arose as to whether Eq. [1] would also be valid under triaxial stress conditions. Tests were conducted on 1/2-in. thick plate material having a composition of 9 Cr-8 Ni-4 Mo-2 Mn-2 Si-0.27 C. It was found that sectioning, polishing, and etching of fractured specimens could reveal the strain-induced martensite occurring at a crack tip. Care had to be taken to minimize the final polishing steps so as to avoid a smeared layer of strain-induced martensite. The method for taking metallo-graphic samples from fractured crack-line loaded type samples is shown in Fig. 1. Observations of the strain-induced martensite occurring at room tem-

Jan 1, 1970

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By T. N. Williamson

6.3-1. Historical Development. Rotary drilling has been used in surface mining for many years. Its principal use is for primary blasthole drilling. In this use, holes in the range from 4 to 15 in. in diameter are drilled in overburden and massive ore bodies for large initial blasting operation. With properly designed shot patterns and loading, secondary blasting is seldom required. The use of rotary drilling with diamond bits for exploration is discussed in Chapter 3.1. Small rotary drillholes of approximately 2-in. diameter are employed as blastholes to shatter uncovered coal seams, but this is a minor part of surface mining drilling operations. Another minor use of rotary drills in surface mining is for placing wire saw poles in dimension stone quarries, usually accomplished with large-diameter calyx or steel shot drills. Primary blasthole drilling by the rotary method was performed with drag bits until 1949 (19). Its use in mining was only in soft formations, so that rotary drills prior to that time were found principally in overburden drilling for the surface mining of coal. In 1949 it was found that air circulation to remove cuttings resulted in increased penetration rate and prolonged life for the rolling-cutter type of bits. Prior to that time, and since their introduction in oil well drilling in 1907, water had been used for circulation with these bits. The dependence on water to clean the hole had delayed the acceptance of bits with rolling cutters in mines because of water haulage and freezing problems as well as the loss of water through cracks in the formation. After rolling cutters were introduced, subsequent improvements in tools made rotary drilling adaptable to harder formations (18). This system is now used in the hardest formations encountered in mining. 6.3-2. Principles of Operation. ENERGY. Rotary drills attack rock with energy supplied to the bit by a rotating drill stem, and infrequently by

Jan 1, 1968

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

By G. R. M. Del Giudice

The term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(l)† Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince;(3) Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) Old Theory of Slime-coatings At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed. The cell was made of bakelite and had platinum electrodes. Objectives were employed which had a working distance of at least three millimeters,1 and the parts of the mounting which came in contact with

Jan 1, 1935

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

1. How Does One Determine Whether an Ore Body Will Block-cave? Page Mark A. Smith......... 122 Harry A. Leidich........ 122 McHenry Mosier ...,.. 22 R. W. Hughes ........ 122 Sherman R. Burdick ....... 123 R. T. Gallagher........I 23 Benjamin F. Tillson...... 123 Lucien Eaton...........123 C. F. Jackson..... . .. 123 Philip B. Bucky........... 126 2. How Does One Determine the Block Dimensions and the Development Work Necessary to Make an Ore Body Cave? Mark A. Smith... 125, 127, 129 Harry A. Leidich..........126 McHenry Mosier......126, 127, 132 R. W. Hughes...........126 Sherman R. Burdick.........127 R. T. Gallagher...........127 Benjamin F. Tillson......127,131 L. E. Young............127 Robert D. Hoffman.......128, 132 Gerald Sherman..........128 Philip B. Bucky......130, 131, 132 K. S. McClellan..........132 Tell Ertl.............132 3. How Do the Forces Act and What Are the Stresses Developed in a Block That Cause It to Block-cave? Mark A. Smith.........132, 135 Harry A. Leidich........133 McHenry Mosier . .. 133 R. W. Hughes ....... 133 Sherman R. Burdick..... . 133 R. T. Gallagher..........134 C. F. . Price, Jr. ........134 Benjamin F. Tillson.........134 C. F. Jackson......134, 135,137 R. Taborelli...........135 Frank A. Ayer ... .....136 Philip B. Bucky . .........136 Rollin Farmin . . .......136 . . . Weysser.....135, 136, 137 George S. Rice...........137 4. What Determines the Procedure in Removing Caved Ore? Harry A Leidich...........137 McHenry Mosier........137,141 R. W. Hughes...........137 Sherman R. Burdick........138 R. T. Gallagher...........138 Mark . Smith...........138 Philip B. Bucky......140,141,143 C. F. B. Price, Jr..........140 R. H. Bennett...........141 C. F. Jackson..........141, 143 Gerald Sherman..........141 Tell Ertl.............141 .. .. ..................143 C. H. Shoemaker..........143 5. What Are the Criteria for Determining the Efficiency of a Block-caving Operation? Harry A. Leidich.......... 143 McHenry Mosier......... 144 R. W. Hughes........... 144 Sherman R. Burdick.......144 R. T. Gallagher . ......... 144

Jan 1, 1946

By Clarence Carleton Semple

At a number of mines in eastern Nicaragua, 3.5- or 5-ft. Huntington mills are used for grinding gold-ore after a pre-liminary breaking in jaw-crushers. The smaller mills are made sectional to facilitate transportation to the more difficultly accessible mines. The capacity of the smaller mills is about 20 or 25 per cent. that of the larger, but in proportion to the quantity of ore ground they require more power and are subject to greater wear. The notes herein given are from records of the performance of the larger mills at one of the mines, but, in general, apply to the smaller mills also. The Nature of the Ore. The ore occurred as a series of flat veins in a' highly-decomposed rock, probably alaskite. The primary mineralizatioll comprised pyrite, pyrrhotite, marcasite, chalcopyrite, and quartz; the oxidation-products of which were chiefly hydrated iron oxide or limonite, chrysocolla, azurite, and malachite. The kaolinization of the feldspar of the country resulted in the admixture of a great quantity of clay with the oxidized ore. The quartz was sandy, imbedded in the clay; and probably the greater part represented the residue from the crushed rock in the fissures after leaching, and kaolinization of the feldspar. There was little vein-quartz in the unaltered primary sulphide ore. Only the oxidized ore was mined for the gold that it contained in amouiits that averaged $4 per ton. No specks of gold mere ever seen in the ore, and the gold obtained by panning was always exceedingly fine. The amalgamation-bullion was about 800 fine in gold and from 60 to 80 in silver. The ore delivered at the mill contained from 5 to 15 per cent. of moisture; during the rainy season the quantity was much greater. The moisture and clay made the ore so sticky that it had to be raked over steeply-inclined grizzlies; it hung in the ore-bins,

Jan 1, 1912

By D. T. MacRoberts

Tins paper embodies the results of theoretical studies concerning gas reservoirs, especially the effect of drilling programs of various intensities upon pressure depletion and ultimate recoveries. The primary objective has been to determine the net quantity of recoverable gas that could be obtained as a result of each additional well, in comparison with the gas that might be secured from a single well ideally placed with respect to both acreage and geological structure. No method is yet known whereby the relative merits of intensive and sparse drilling can be compared experimentally; a reservoir must either be drilled closely or developed with wide spacing, but both programs cannot be conducted simultane-ously. Hence, the analytical method seems to be the only approach to the problem. While the present state of our theoretical knowledge does not offer a precise solution to the problem of gas flow in sand bodies, it takes such appropriate cognizance of the limitations of the methods used as to restrict any answer obtained to the realm of engineering accuracy. In solving the problem for the average gas field, it was found that practically the same answers resulted as to pressure distribution, regardless of the size of the drainage radius, even though the latter was assumed to vary from a few feet as a minimum to that of the entire reservoir as a maximum. Such limits represent extreme possibilities; therefore, the practical conditions that are associated with normal development programs, in which wells are placed in the center of tracts varying in size from 40 to 640 acres, will of necessity result in less extreme variations than those indicated in the tables accompanying this paper. Stated more concisely, the amount of gas unrecovered at abandonment (of the particular field used for illustrative purposes) will lie somewhere between 4.6 and 6 per cent of the total original content, no matter how intensively the field is drilled.

Jan 1, 1938

By P. B. Elkin, K. C. Ten Brink, Allen D. Garrison

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940