Search Documents

By T. S. Taylor

THE development of the linear hot-wire anemometer has been chiefly clue to the efforts of L. V. Kings1 and A. E. Kennelly and H. S. Sanborn.2 The anemometers used by these investigators consisted essentially of a fine heating wire having attached leads for resistance measurements at distances of 10 or more centimeters from each other. In using such an anemometer, the current is measured that is necessary to maintain the resistance of the wire, between the two leads, constant for different air velocities. Thus resistance is always so chosen that the temperature of the heating wire will be sufficiently high to make the observations practically independent of small variations in the temperature of the gas in which the anemometer is placed. The measurement of the resistance of the anemometer wire requires a Kelvin bridge set up, which for commercial work is not altogether desirable. The cooling effect clue to different air velocities depends on the temperature difference between the wire and the gas and the total quantity or mass of gas passing the wire per unit tine. Since the temperature of the wire is maintained constant, the effect observed in the change in the heating currentfor a given change in air velocity is a measure of the difference between the gas flow in the two cases. Such an anemometer, therefore, measures the average gas flow for a length depending on the distance between the two resistance leads. Therefore the instrument in the form used thus far is not very satisfactory for measuring gas velocities in small tubes or in places where the velocity varies rapidly across the line of flow. For the purpose of measuring gas flow through relatively small tubes, where the velocity changes rather rapidly across the tube, the hot-wire anemometer has been modified in the manner shown diagrammatically in Fig. 1. It consists essentially of a platinum heating wire H about 0.007 in. (0.178 mm.) in diameter and ½ to 1 in. (12.7 to 25.4 mm.) long stretched across a suitable framework, say of glass. This wire has

Jan 9, 1919

By Gilbert Cady

EXTENSIVE Sampling of coal in Illinois during the past 10 or 12 years by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The sulfur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jack-son County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area Underlain by coal having less than 1.25 per cent, sulfur.

Jan 7, 1919

By V. R. Garfias R. V. Whetsel

Production of crude petroleum in Mexico during 1935 totaled approximately 40,082,000 bbl., an increase of 1,925,000 bbl. over the previous year. Successful development continued in the Poza Rica field during the year, increasing production in that area from 3,708,000 bbl. in 1934 to 9,542,000 in 1935. The output of the South fields (Golden Lane) area decreased by 3,000,000 bbl. during the year, and the heavy-oil district of the Northern fields by 1,500,000 bbl. Production in the Tehuantepec fields showed a slight gain. Production of natural gasoline increased from 430,000 to 600,000 bbl. in 1935. Crude run to stills in local refineries is estimated at 30,000,000 bbl., some 4,000,000 bbl. more than in the previous year. Exports of crude and refined products were approximately 22,000,000 bbl., or 2,000,000 bbl. less than in 1934. Exclusive of ships bunkers, domestic consumption increased about 900,000 bbl. during the year, reaching an estimated total of 14,500,000 barrels. Only 74 wells were completed, as compared to 148 in 1934 and 91 in 1933. In proven areas 58 completions resulted in 33 producers and 25 failures. In northeastern Mexico, near the United States border, six wildcat wells were completed, all of which gave little or no encouraging results, except Rancheria No. 3, near Camargo, which is a fair-sized gas well. Four wildcats were drilled just northeast of the Northern fields (heavy-oil district), all of which were failures. A deep test was completed a short distance southeast of the Golden Lane (South fields) in Palo Blanco, which encountered small production not sufficient to exploit. On the Isthmus of Tehuantepec a wildcat well was completed for an estimated initial production of 2000 bbl. daily, a short distance south of the old Jalapa field, which was perhaps the most important new development of the year. Four other wildcats drilled in the Isthmus district resulted in failures. Fields Northern Fields (Heavy-oil District).—In the Northern fields, 18 producing wells and 20 failures were completed, as compared to 34 producers and 71 failures in 1934. The initial production of the new

Jan 1, 1936

Lieut. Maxwell E. Erdory, now with the Army of Occupation in France, writes as follows: "The 602d Engrs., many of whose officers are members of the Institute, started its active service in France at Avocourt, where we built a road across `No Man's Land.' This road from Avocourt to Montfaucon started us on a career of road building which lasted from Sept. 26 to Nov. 9. The engineer in war has no working hours. Our first job meant 50 hr. continuous work, a layoff of 4 hr. and 18 hr. more. That was our initiation in this war game. "Back in the States we practised building trenches, dugouts, and underground shelters of all sorts. In France we were unfortunate enough to come upon the scene when the so-called open warfare started. That made all the above unnecessary. Roads was the cry and our job was to see that all the artillery got their roads and got over them. "I might mention here that the roads of France, which were in excellent condition except for numerous shell holes, w re one of the leading factors in the rapid termination of the war. "We built a narrow-gage railroad from Romagne to Landre St. George which cost us a few men. At Stenay we did our first bridge building. We built nine bridges across the Meuse, capable of carrying tanks, in 18 hr. The next day the American army crossed these bridges on their way to Virton, Belgium, and the Rhine. " Our course from Virton, Belgium, took us through Longwy, Musson, and Athus, in which towns I inspected the steel plants. In Musson as well as Longwy the Germans had destroyed most of the blast furnaces. This destruction began in August, 1917. In Athus the furnaces were in good condition, the Germans having removed all motors land electrical apparatus, rendering the plant inoperative. I have taken several photos of interest of these plants. "It is but fitting that I say that the engineer in this war has contributed much toward its success but the "Doughboy" is its hero and we engineers one and all say "All hail the Doughboy."

Jan 2, 1919

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By Albert F. Schneider

The peculiar conditions under which lead and silver ores are now smelted in Salt Lake Valley, Utah, render it advantageous to make slags that are siliceous and carry a high percentage of lime. The ores treated come from Utah, Idaho, Montana, and Nevada; nine-tenths coming from Utah. These ores are siliceous, and contain but little fluxing material; the iron present scarcely sufficing for the sulphur and arsenic. Formerly ores high in iron were furnished from Cottonwood Canons, but this supply is meagre. The ores from Idaho, Montana, and Nevada are high grade galenas, more or less impure. They generally require a large amount of iron for the sulphur, arsenic, and antimony. In the winter and spring of 1880—'81, we were treating at the Germania Works principally Bingham Canon lead ores and silver ores from Tintic. The former contained 15 to 30 per cent. silica, and only 4 to 5 per cent. iron (generally as iron pyrites); they ranged high in lead and low in silver, and carried more or less alumina; the lead was present chiefly as carbonate. The silver ores from Tintic contained sulphides, and ran as high as 80 per cent. silica. We had been running on a slag approximating 40 per cent. FeO, 20 per cent. CaO, 10 per cent. other bases, and 30 per cent. SiO2, which had heretofore been very satisfactory; but with the class of ores then coming in it was of the utmost advantage to use less iron and more lime, especially as the iron ore (50-55 per cent. iron and 5-7 per cent. silica) cost four times as much as the limestone (50-55 per cent. lime, 3-5 per cent. silica). The large amount of alumina in the slag influenced them for the worse; the addition of lime to the charge helped them, and after many experiments regarding the proportion of FeO, CaO, and SiO2, a slag approximating 35 per cent. FeO, 25 per cent. CaO, 5 per cent. other bases, and 35 per cent. SiO2 seemed to answer

Jan 1, 1883

By S. W. Hurlbut

12.4 Application of Research Findings. After the findings of research have been evaluated and approved, there remains the problem of translating them into practical usage. It frequently happens that this is the more difficult phase of the research project. Hitherto, the problems have been largely associated with material objects and scientific laws. When the findings of research are implemented in the field, the human factor becomes the most important element bearing on success or failure. From this point on, the attitudes and reactions of people of all kinds are involved, and just how they are involved and their relation to successful implementation is the subject of the remainder of this section. 12.41. Management Attitudes. To engage in research at all implies management backing to a degree. But this could be dictated by overall company policy or by just some executives in the hierarchy of management. The existence of research per se does not necessarily mean that there is a solid, unanimous echelon of management executives who sincerely believe in the fruits of research, who have an earnest desire to make breakthroughs, and who have a willingness to take calculated risks. Under the ideal condition of complete management backing, translating the results of research into practice is greatly facilitated. If management accepts the results of research as valid, the order is given, or it has been established by precedent that those results will be implemented. The rest of the organization will have grown to accept the fact that this is so, and that the results must be given a fair trial in the field. However, this ideal condition probably exists but rarely, and it is against a background of incomplete, or partial, management backing that most results of research must be implemented. At the present time, the climate for research in the mining field is less than perfect but is improving rapidly as the realization grows within the industry that the way toward taking its proper place in the Space Age is by applying to mining the philosophy and techniques of research that made the Space Age possible.

Jan 1, 1968

By Wilson B. Emery

The Hidden Dome gas field, situated in Washakie County, Wyoming, was discovered Sept. 26, 1917. Subsequently five additional gas wells were completed and a large reserve was developed. For a number of years this field completely supplied the domestic market at Basin and Greybull, as well as the refinery at the latter town, and it is still supplying gas in small amounts to this market. Production is obtained from the sands of the Frontier formation at depths ranging from 1000 to 1500 ft. The original rock pressure was 725 Ib. and initial production ranged from 4,000,000 to 28,000,000 cu. ft. per day per well. Porosity of the sand, determined from the size of the productive area and the amount of gas recovered, is over 18 per cent. Area and Management It is estimated that the productive area is about 640 acres. Its outline is indicated on Fig. 5, on which are also shown the locations of holes drilled on the structure and the area of unit operation. The unit area is owned by the Ohio Oil Co. and development and operation have been by this company. No productive well has been completed outside this area. The entire area was Government land filed on under the placer mining law. Results of Unit Operation With six producing wells, or an average of one to each 160 acres, the pool is completely developed. Location of the wells was made with respect to structural conditions plus the requirement that at least one well be drilled on each 160-acre placer claim. Perhaps a somewhat more uniform spacing of the wells might have been accomplished and one well eliminated, but it must be borne in mind that the holes, on account of their shallow depth, were not expensive and that the object was to develop as reliable a reserve as possible. There is no cause to suspect that these holes have not adequately drained the reservoir and there is every reason to think that any additional wells, which might have been drilled under diversified ownership and operation, would have been an economic waste. Unit operation by a competent company has not only resulted in the elimination of loss of gas through careless development and operation

Jan 1, 1930

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By E. J. Bruderlin

A metallurgical process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the distillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working blóck must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retorting plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties. Amarillo Silicon Carbide Retorts At the Amarillo plant of the American Smelting and Refining Co. a retort made of a suitable plastic clay grogged with silicon carbide has been found to best meet the present-day requirements. Retorts of this kind have been in use at Amarillo for 8 years and have shown an average furnace life of approximately 175 calendar days. The Amarillo retort is cylindrical in shape and after burning is approximately 83/4 in, inside diameter by 60 in. over-all length. The wall thickness is 136 in., except for the butt of the retort, which is approximately 2½ in. thick. The retort mud has a shrinkage of 3 per cent, or approximately % in. per foot. The silicon carbide retort after being properly dried weighs about 211 lb. When the retort is fired and ready to go into use the weight decreases to approximately 203 lb.

Jan 1, 1937

By V. R. Garfias R. V. Whetsel

Production of crude petroleum in Mexico during 1935 totaled approximately 40,082,000 bbl., an increase of 1,925,000 bbl. over the previous year. Successful development continued in the Poza Rica field during the year, increasing production in that area from 3,708,000 bbl. in 1934 to 9,542,000 in 1935. The output of the South fields (Golden Lane) area decreased by 3,000,000 bbl. during the year, and the heavy-oil district of the Northern fields by 1,500,000 bbl. Production in the Tehuantepec fields showed a slight gain. Production of natural gasoline increased from 430,000 to 600,000 bbl. in 1935. Crude run to stills in local refineries is estimated at 30,000,000 bbl., some 4,000,000 bbl. more than in the previous year. Exports of crude and refined products were approximately 22,000,000 bbl., or 2,000,000 bbl. less than in 1934. Exclusive of ships bunkers, domestic consumption increased about 900,000 bbl. during the year, reaching an estimated total of 14,500,000 barrels. Only 74 wells were completed, as compared to 148 in 1934 and 91 in 1933. In proven areas 58 completions resulted in 33 producers and 25 failures. In northeastern Mexico, near the United States border, six wildcat wells were completed, all of which gave little or no encouraging results, except Rancheria No. 3, near Camargo, which is a fair-sized gas well. Four wildcats were drilled just northeast of the Northern fields (heavy-oil district), all of which were failures. A deep test was completed a short distance southeast of the Golden Lane (South fields) in Palo Blanco, which encountered small production not sufficient to exploit. On the Isthmus of Tehuantepec a wildcat well was completed for an estimated initial production of 2000 bbl. daily, a short distance south of the old Jalapa field, which was perhaps the most important new development of the year. Four other wildcats drilled in the Isthmus district resulted in failures. Fields Northern Fields (Heavy-oil District).—In the Northern fields, 18 producing wells and 20 failures were completed, as compared to 34 producers and 71 failures in 1934. The initial production of the new

Jan 1, 1936

By Walter Miller

Any review of the engineering progress made in 1932 in the petroleum refining industry must necessarily be broad and general, improvements having been made in practically all major branches of this activity. Several factors contributed to an advancement on a wide front, much of it coming from those active in refining, considerable from those not, immediately in it but engaged in designing and installing equipment and maintaining large and capable staffs of experts in both engineering and development work. Another factor has been the ability of the refiner, because of less than capacity operation, to carry on experimental and development work in regular plant equipment. The movement to higher antiknock value gasoline has continued through 1932, and the average improvement of the more widely sold branded gasolines is from 3 to 4 points higher in the octane scale. A very great improvement was brought about during the year in the method of determining the octane number of gasoline. While the procedure and equipment for determining this value as developed by the Cooperative Fuel &search Steering Committee prior to 1932 had received fairly general acceptance, evidence that it did not always evaluate in a measure consistent with road performance quickly accumulated, and led to further effort to synchronize laboratory results with actual use. As the result of some really brilliant work on the part of the C.F.R. Committee and a large number of collaborators, it was found that a comparatively minor modification of the previously developed equipment and method gave surprisingly concordant results between laboratory tests and trial per-formance on the road. This method has been officially accepted by the Society of Automotive Engineers and the American Petroleum Institute, and will according to present plans go into general use on April 1, 1933. The American Society for Testing Materials has studied the method but at the time of writing this had not reached a final decision regarding it. Improved Volatility of Gasoline The most notable trend during the year, in addition to a very considerable increase in antiknock value referred to above, has been in the

Jan 1, 1933

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾ -in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 ½ -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A 3/4-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1938

By C. H. Stein

THE Pennsylvania Legislature, on March 13, 1837, passed an act authorizing the Lehigh Coal & Navigation Co. to construct a railway to connect the North Branch Division of the Pennsylvania Canal with the slack water navigation f the Lehigh River; the navigation company accepted this act on May 10, 1837. Edwin A. Douglas, chief engineer for the navigation company, located the route for this railway from White Haven to Wilkes-Barre, which was called the Lehigh & Susquehanna Railroad. The object was to transport coal from the Wyoming Valley, of Pennsylvania, to the Atlantic seaboard. This railway was considered a marvelous piece of engineering, as it included a tunnel nearly 13 mi. long, and a series of inclines, or planes, up which the cars laden with coal were raised from the vicinity of Ashley to the summit f the mountain near Solomon's Gap, whence they were taken to White Haven by rail. There the coal was transferred to canal boats. In June, 1862, floods almost completely destroyed the upper division of the canal, so on March 4, 1863, the Pennsylvania Legislature passed an act prohibiting its restoration, but granted a charter for the construction of a railway from White Haven to Mauch Chunk to connect with the line from White Haven to Wilkes-Barre, previously built. On March 16, 1864, a supplementary act was passed extending the Lehigh & Susquehanna Railroad to Easton, Pa. This completed a direct all-rail route from Wilkes-Barre to the New York harbor (by way of the Central Railroad of New Jersey). Up to this time, all freight and passenger traffic passed over the planes, but in 1866 and 1867 there was constructed what was known as the "back track" down the mountain side between Solomon's Gap and Ashley over which all the passenger traffic and empty cars thereafter passed; it is now known as part of the main line. For the handling of the heavy coal traffic, however, this would have involved a continuous climb from Ashley, 170.27 mi., from New York, to Solomon's Gap, 157.8 mi. from New York, or a distance of 12.47 mi., and a total ascent of 1,013.75

Jan 9, 1921

By William Vietti

WEST TEXAS and New Mexico has been overshadowed by the develop-ment in East Texas to such an extent that the area has been placed on a settled production basis by most of the operators. Considerable develop-ment work on both proven and unproven acreage remains to be carried on, but the incentive, a ready and profitable market, has been lacking. The main characteristics of the fields in this area are so well known that they are not described again in this paper, which thus resolves itself into a statistical review of the more important production features of the area. Proration has been in effect during the year and has been rigorously applied with the full cooperation of all producers. Proration in West Texas and New Mexico is based in the more pro-ductive fields on a potential and acreage distrbution of the allowance to the individual wells or acreage units. Potentials are determined generally by a short production test of from 1 to 4 hr.; and the hourly rate is multiplied by 24 to obtain the 24-hr. production or rated potential of the separate wells. The potential values thus set up have been questioned by many production men who are not willing to concede that the instantaneous (hourly) capacity of a well to produce is its potential capacity for a day with all other wells in the pool producing at their capacity. However, the potential of a well determined as above remains its chief rating as a measure of the permeability in place and as an indication of the possible reserve feeding that well. , The acreage factor has made it unnecessary to overdevelop properties in order to obtain an allowance proportionate to neighbors who are willing to drill an excessive number of wells on a piece of acreage in the hopes of a quick drainage and a corresponding profit. Proration has resulted in an orderly development of many of the pools in this area on the base as out-lined above, resulting in more reasonable spacing of wells and the more even withdrawal of oil and the ensuing expectation of high recoveries.

Jan 1, 1933

By Gary P. Thomason

INTRODUCTION One may have heard about how various projects were financed or certain companies were successful in obtaining a bank loan, but there are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of debt financing sources available to finance minerals operations (see the next Chapter 11), but these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to many minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. LOAN APPROVAL PROCESS The initial stages of the loan approval process should begin long before the bankers, and the organizations they represent, enter upon the scene. The loan approval can be broken down into six stages: 1) Generation 2) Preparation 3) Presentation 4) Evaluation 5) Approval 6) Documentation As you can see in Figure 1, the bank is only directly involved in the second half of the process. The perils in obtaining financing for the smaller minerals venture are primarily in the first three stages, not the last three. The minerals venture making application for a loan can, in almost every case, improve its chances of success by carefully planning and preparing itself and the information that will be required of it in the loan approval process. Generation This first step in the process is deciding on the need for a loan. (Earlier papers in this Book and in Chapter 11 provide some guidance.) It is surprising how many ventures confuse the need for money with the need for a loan. Suffice to say that the equity investor risks both the timing of the yield on his capital and, ultimately, his capital. The lender, on the other hand, advances temporary funds which he expects to be repaid on a specific schedule with a fixed

Jan 1, 1985

By William Blauvelt

THE type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay is flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J.. Taylor, and described by him in 1881.1 This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25° from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle.. Depth of the coal above the tuyere; 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. . The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not he made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages:

Jan 12, 1913

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940