Search Documents

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By Shueling Woo, Charles S. Barrett, Robert F. Mehl

When one solid phase is generated from another, fixed and rational orientation relationships are observed to subsist between the parent and the new crystal. The principle has been proposed1 that the relationships obtaining between the same two phases are identical whatever the type of phase change involved, or whichever of the phases may act as parent. Many types of phase changes have been studied: allotropic transformations in pure metals, precipitation from solid solutions, eutectoid decompositions, peritectic reactions, the formation of oxide layers, and others2 Phase layers generated by diffusion of one metal into another constitute an additional type of reaction. This report provides new data on the orientation relationships occurring between phase layers formed by diffusion, in the Cu-Zn system,§ and furnishes further evidence in support of the principle. Materials and Methods The Cu-Zn system is especially suitable for these studies since the high vapor pres- sure of Zn provides an opportunity readily to create one phase poorer in Zn upon a parent phase richer in Zn by removing Zn by vaporization, or to reverse this process by adding Zn from Zn vapor; e.g., the beta phase can be found as a layer upon gamma by dezincing, or gamma can be found on beta by addition of Zn from Zn vapor. Since orientation relationships are to be sought, requiring crystals large enough for orientation determinations, it is convenient to prepare single crystals or large grains of the parent phase. The samples were prepared from oxygen-free high-conductivity copper and Horse Head zinc by melting under a borax flux in a graphite crucible. Large crystals of beta brass were grown by the strain-anneal method, in plates sectioned from the cast ingots, by the following procedure. Rockwell-hardness indents were made at I cm. intervals and with various loads, then the plates were annealed for 4 days at 700°C. in Nichrome boxes packed with beta-brass chips and graphite. Surface layers were removed by grinding and etching to a depth of about 1.0 mm., and individual grains were cut out. Crystals of alpha and gamma brass were prepared by freezing, by lowering a graphite crucible at speeds less than one inch per hour through a furnace held at a constant temperature above the melting point. Single crystals were cut out with a jeweler's saw, ground, polished and etched. Care was taken to remove cold-worked layers from the finished crystals

Jan 1, 1944

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy's Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy's Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Charles S. Barrett, Robert F. Mehl, Shueling Woo

When one solid phase is generated from another, fixed and rational orientation relationships are observed to subsist between the parent and the new crystal. The principle has been proposed1 that the relationships obtaining between the same two phases are identical whatever the type of phase change involved, or whichever of the phases may act as parent. Many types of phase changes have been studied: allotropic transformations in pure metals, precipitation from solid solutions, eutectoid decompositions, peritectic reactions, the formation of oxide layers, and others2 Phase layers generated by diffusion of one metal into another constitute an additional type of reaction. This report provides new data on the orientation relationships occurring between phase layers formed by diffusion, in the Cu-Zn system,§ and furnishes further evidence in support of the principle. Materials and Methods The Cu-Zn system is especially suitable for these studies since the high vapor pres- sure of Zn provides an opportunity readily to create one phase poorer in Zn upon a parent phase richer in Zn by removing Zn by vaporization, or to reverse this process by adding Zn from Zn vapor; e.g., the beta phase can be found as a layer upon gamma by dezincing, or gamma can be found on beta by addition of Zn from Zn vapor. Since orientation relationships are to be sought, requiring crystals large enough for orientation determinations, it is convenient to prepare single crystals or large grains of the parent phase. The samples were prepared from oxygen-free high-conductivity copper and Horse Head zinc by melting under a borax flux in a graphite crucible. Large crystals of beta brass were grown by the strain-anneal method, in plates sectioned from the cast ingots, by the following procedure. Rockwell-hardness indents were made at I cm. intervals and with various loads, then the plates were annealed for 4 days at 700°C. in Nichrome boxes packed with beta-brass chips and graphite. Surface layers were removed by grinding and etching to a depth of about 1.0 mm., and individual grains were cut out. Crystals of alpha and gamma brass were prepared by freezing, by lowering a graphite crucible at speeds less than one inch per hour through a furnace held at a constant temperature above the melting point. Single crystals were cut out with a jeweler's saw, ground, polished and etched. Care was taken to remove cold-worked layers from the finished crystals

Jan 1, 1944

By R. E. Zimmerman, T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1950

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

POLITICAL developments, the impact of Korean warfare necessitating immediate rearmament plans, and recent developments in mining taconites have focused attention on their immediate exploitation to fill the gap created by diminishing reserves. The question of rich foreign ores versus low grade development is past-we need both sources with emphasis on the immediate large scale mining of taconites. In the past three months several things have occurred which add to the taconite picture: (1) Pellets have been used successfully in the blast furnace by Armco. (2) In Congress HR 8512 was introduced by Congressman Blatnik of Minnesota to amend the lending powers of RFC to permit long term loans on basic mining developments, particularly the taconites, which may be needed for the strengthening of the national economy. (3) Walter S. Tower, president of the American Iron & Steel Institute, announced that American steel companies are planning expansion of 6,000,000 tons of steelmaking capacities in the next few years. (4) The outbreak of war in Korea has obliged the United States to rearm and make plans for a semipermanent defense establishment to which 10 to 12 pct of the national income will be budgeted. (5) Startling new advances have been made in the Linde Air Products Co.'s jet-piercing drilling. The United States is now confronted with the problem of increasing its steel capacity and at the same time of securing enough iron ore to supply this increase as well as make provision for the rapidly decreasing supply of rich iron ore on the Mesabi range. Taconites, the low grade iron ore at the east end of the Mesabi, of which there are literally billions and billions of tons of easily concentratable magnetic ore, are the immediate answer. According to the Wall Street Journal on July 24: "Reserve Mining Co., backed by such steelmakers as the Armco Steel Corp., Wheeling Steel Co., Republic Steel Corp., is reported ready-as soon as the pending bill clears (HR 8512)-to seek a $100 million federal loan to build a taconite processing plant at Beaver Bay, Minn., to produce about five million tons (of pellets) annually of 60 pct to 65 pct in iron ore . . ." Experimental work indicates that pellets may be the final form, rather than nodules, agglomerates, or sinter. At Ashland, Ky., the Reserve Mining Co., which has obtained a

Jan 9, 1950

The National Research Council was organized in 1916 at the request of the President by the National Academy of Sciences, under its congressional charter, as a measure of national preparedness. The work accomplished by the council in organizing research and in securing cooperation of military and civilian agencies in the solution of military problems demonstrates its capacity for larger service. The National Academy of Sciences is therefore requested to perpetuate the National Research Council, the duties of which shall he as follows: 1. In general, to stimulate research in the mathematical, physical, and biological sciences, and in the application of these sciences to engineering, agriculture, medicine, and other useful arts, with the object of increasing knowledge, of strengthening the national defense, and of contributing in other ways to the public welfare. 2. To survey the larger possibilities of science, to formulate comprehensive projects of research, and to develop effective means of utilizing the scientific and technical resources of the country for dealing with these projects. 3. To promote cooperation in research, at horse and abroad, in order to secure concentration of effort, minimize duplication, and stimulate progress; but in all cooperative undertakings to give encouragement to individual initiative as fundamentally important to the advancement of science. 4. To serve as a means of bringing American and foreign investigators into active cooperation with the scientific and technical services of the War and Navy Departments and with those of the civil branches of the Government. 5. To direct the attention of scientific and technical investigators to the present importance of military and industrial problems in connection with the war, and to aid in the solution of these problems by organizing specific researches. 6. To gather and collate scientific and technical information, at home and abroad, in cooperation with governmental and other agencies, and to render such information available to duly accredited persons. Effective prosecution of the council's work requires the cordial collaboration of the scientific and technical branches of the Government, both military and civil. To this end representatives of the Government, upon the nomination of the National Academy of Sciences, will he designated by the President as members of the council, as heretofore, and the heads of the departments immediately concerned will continue to cooperate in every way that may be required. THE WHITE HOUSE, WOODROW WILSON. 11 May, 1918.

Jan 7, 1918

By Francis Donaldson

THE direct injection of cement grout into water-bearing fissures as a means of checking or stopping the flow of water into shafts and tunnels has been experimented with for a decade or longer and seems to have been first attempted in Europe. The earliest application of which the writer has found a record was at a shaft sunk by the Mining Society of Lens; this is described by C. Dinoire in the Transactions of the Institution of Mining Engineers.1. It is only lately, however, that the process has been entirely successful. This success has been accomplished on the Catskill Aqueduct, now under construction by the city of New York. This aqueduct includes a number of deep pressure tunnels, reached by shafts for both waterway and construction purposes. In portions of these shafts and tunnels considerable underground water was met. The contract for the first of these deep pressure tunnels was let to the T. A. Gillespie Co.; this section is known as the Rondout Siphon. It leads under the Rondout valley at a depth of from 400 to 800 ft. and is about 5 miles long. The engineers expected that considerable water would be encountered, but fortunately this was not the case except at one shaft, known as No. 4, which penetrated the rock at a junction between limestone and conglomerate. Water-bearing fissures were encountered almost immediately. At a depth of about 200 ft. a flow of 1,500 gal. per minute was struck. The shaft then contained as many pumps as could be used, and it seemed impossible to sink it further. After vain efforts had been made to proceed, John P. Hogan, a division engineer of the Board of Water Supply, suggested that cementation of the fissures be tried. The process was attempted for the first time in this country. Since the shaft was partly full of water it was necessary to drill grout holes with a diamond drill. Platforms were placed on the timbers at the water level, the diamond drill was installed and six 90-ft. holes were drilled in the bottom of the shaft. Several car loads of cement were pumped through these holes into the fissures, the drill casings being used for grout pipes. This largely cut off the flow of water from the bottom and sinking could then

Jan 1, 1914

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939