Search Documents

By T. J. Fabiniak, R. A. Dodd, R. Balow

ALTHOUGH the (111) slip direction in pure bcc metals is well established, the information on operative slip planes is less unambiguously interpreted. So far, (110) {112), and (123) slip planes have been identified, but it is not certain whether glide on (112) and (123) really occurs or if it is composite slip on non-parallel (110) planes. The second of these possibilities is supported by the work of Chen and Maddin on niobium and molybdenum, and a subsequent analysis by these same workers of slip in bcc metals generally.3 The alternative possibility is exemplified by the work of Opinsky and smoluchowsky4 who concluded that slip in Fe-Si crystals can occur on any one of the systems {110}(111), {112}(111), and {123)(111), depending on which system the resolved shear stress is highest. Allen et alS5 also found that glide in ar iron could occur on any of these three systems, the operative system being determined principally by orientation. By an analysis of crystal rotation, slip lines, and X-ray asterism Harris6 concluded that niobium also deforms on these same systems, but if one of these glide planes does not coincide with the plane of maximum resolved shear stress, composite slip on nonparallel (110) planes may occur giving a macroscopic high indices slip plane. Earlier work on iron by Vogel and Brick reached the same conclusion.7 The analysis of slip in bcc metals is made more difficult by the fact that the slip lines may be quite wavy. In fact, the generality of wavy slip lines suggests that screw dislocations slip readily from one plane to another in the (111) zone ("pencil glide") although, as noted, it is not certain whether planes other than (110) really contribute to the slip. If planes of higher indices than {110} do operate, there is a possibility they may do so more readily at higher temperature Argon and Maloof9 observed {100}{211}(111) slip in tungsten single crystals plastically strained at low temperatures, but the results were interpreted in terms of an orientation-dependence rather than temperature-dependence. Therefore, at the present time corroborative evidence for the operation of higher indices slip planes at higher temperatures is lacking. The present results were obtained during the course of an investigation into the effect of cathode and anode surface crystallography on the prebreakdown currents of vacuum insulated devices. In the experiment of particular interest, the 1/8-in.-diam anode and the in.-diam cathode were tungsten crystals (total impurities -230 ppm) with (110) and (100) faces respectively. The faces were electrolytically planed and examined for initial perfection by plastic/carbon replicas and a study of Kikuchi lines in reflection electron diffraction patterns. They were aligned precisely parallel in an insulating holder incorporated into the electron microscope, the measured microscope vacuum being 2 x 10-5 torr, and the electrode spacing 0.01524 cm. The anode structure shown in Fig. 1 was obtained

Jan 1, 1970

By C. H. Ma, J. S. Makris

This paper describes a modified X-ray diffraction microscope wzethod based on the general principles of Berg-Bawett's Method, Lang's Method, and Woosters1 Technique. This new method may be used for stationary or oscillatory photomacrographs, with both reflection and transmission techniques. In the stationary technique, a small point-source of a divergent X-ray beam of white radiation is used; in the oscillatory technique, a monochromatic divergent beam is employed. The chief advantages of the method described herein are that only approximate alignment of the Bragg angle -of-interest is needed during exposure, and that a large portion of a crystal-specimen surface can he irradiated. In recent years, the study of dislocations through X-ray diffraction microscope techniques has received considerable attention as concerns the per,fection of single crystals. Very promising results have appeared in the literature.'-' These techniques are very useful when the dislocation density of a crystal is near 105 per sq cm or lower. The principle of X-ray diffraction microscopy is based on the differential effect of X-ray primary extinction between the distorted parts and the perfect parts of a crystal. When an X-ray beam impinges on a set of planes of a crystal at the correct Bragg angle, diffraction of X-rays will occur with a 90-deg phase shift of the diffracted beam. This once-diffracted beam still forms the correct Bragg angle with the planes ahead of it, if the planes are not distorted. Thus, part of the strength of the once-diffracted beam is rediffracted and the beam continues to travel in the direction of the primary X-ray beam. This twice-diffracted beam not only takes away part of the strength of the once-diffracted beam, but also causes destructive interference with the primary beam because it now is exactly 180 deg out of phase with the primary beam. As the primary beam goes farther and farther into the crystal, its intensity is continuously weakened. Asa result, the ultimate X-ray diffraction power of a set of undistorted planes is largely extinguished. This phenomenon is called primary extinction.1,2'4 If the set of planes ahead of it is distorted, the once-diffracted beam will have less chance to be rediffracted, because it could not meet the exactly correct Bragg angle for rediffraction. If a part of the beam does rediffract, this twice-diffracted beam is not exactly 180 deg out of phase with the primary beam, and thus it causes less destructive interference. As a result, the registered X-ray diffraction power of the distorted part of a crystal appears stronger than that of the perfect part. Thus, point-by-point contrast of a diffraction image is theoretically possible from a crystal containing dislocations. Two most popular X-ray diffraction microscope techniques today are Berg-Barrett's Method and Lang's Method. Both of these techniques require a

Jan 1, 1964

By L. S. Darken

IT has been known for sometime that in an ionic lattice, such as that of Ag2S or FeO, the migration velocity of the anion may differ markedly from that of the cation, the cation being usually the more mobile. It has been shown, for example, that during the formation of silver sulfide tarnish on silver, the tarnish layer grows principally by the motion of silver cations through an essentially stationary silver sulfide lattice. Similarly, the growth of wüstite scale on iron proceeds principally by motion of iron ions, this being accomplished with the aid of vacant iron lattice sites into which the iron may readily move. Likewise investigations of solid solutions of various salts show that there is usually considerable difference in the mobility of the different cations. Measurements of the mobility of various metals in liquid mercury indicate that the various metals move at different rates relative to the mercury. In view of the foregoing it seems reasonable to suppose that when any single phase solution is acted upon by a field, the atoms of different elements respond in different ways; in particular, that the force arising from a particular concentration gradient in a binary alloy would cause the atoms of one component to move with a drift velocity which is in general different from that of the atoms of the other component. The recent experiments of Smigelskas and Kirkendall1 support this viewpoint, since they found, in essence, that during diffusion in alpha brass zinc moves appreciably faster than copper. This was evidenced by the relative motion of inert molybdenum wires. Such a phenomenon is incompatible with the place interchange theory of diffusion proposed by several authors, most recently by Birchenall and Mehl.2 This theory has, however, also been questioned3.4 for other reasons, principally because of the high energy required for direct atomic interchange. The rather large difference between self-diffusivity, as determined by tracer technique, and mutual diffusivity, as determined with the aid of another element at low concentration, might also be interpreted as favoring the above idea; however, Birchenall and Mehl have pointed out that there is another possible interpretation of this difference; this is discussed later. A rather interesting and pertinent observation was made by Schwartz,5 who noticed that tungsten lamp filaments, heated by direct current, commonly fail by necking down in the region at the temperature gradient near the positive end, with a concomitant swelling at the corresponding position near the negative end. He introduces considerable auxiliary evidence to show that this phenomenon is occasioned by the motion of tungsten cations which migrate in the high temperature region from the positive end toward the negative end. The mechanism of this migration is not clearly understood. If, however, this experimental evidence be accepted, we are forced to conclude that alloying elements in the tungsten may migrate by the same or a similar mechanism, whatever it may be, at a greater or lesser rate, thus giving rise

Jan 1, 1948

By B. M. Larsen

IN endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary importance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a clear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carbon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. REACTION RATES AT STEELMAKING TEMPERATURES General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase -that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: I. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrin1 has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjusted immediately. 3. Barret, Holbrook and Woods observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By B. H. Sage, W. N. Lacey

The results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of grave! screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. Introduction Gravel screens have been placed in water and oil wells for a number of yearsl,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. Influence OF Gravel Screens upon Productivity The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1942

By A. G. Weber, K. H. Coats, M. H. Terhune, R. L. Nielsen

Two computer-oriented techniques for simulating the three-dimensional flow behavior of two fluid phases in petroleum reservoirs were developed. Under the first technique the flow equations are solved to model three-dimensional flow in a reservoir. The second technique was developed for modeling flow in three-dimensional media that have sufficiently high permeability in the vertical direction so that vertical flow is not seriously restricted. Since this latter technique is a modified two-dimensional meal analysis, suitably structured three-dimensional reservoirs can be simulated at considerably lower computational expenses than is required using the three-dimensional analysis. A quantitative criterion is provided for determining when vertical communication is good enough to permit use of the modified two-dimensional areal analysis. The equations solved by both techniques treat both fluids as compressible, and, for gas-oil applications, provide for the evolution of dissolved gas. Accounted for are the effects of relative permeability, capillary pressure and gravity in addition to reservoir geomety and rock heterogeneity. Calculations are compared with laboratory waterflood data to indicate the validity of the analyses. Other results were calculated with both techniques which show the equivalence of the two solutions for reservoirs satisfying the vertical communication criterion. INTRODUCTION Obtaining the maximum profits from oil and gas reservoirs during all stages of depletion is the fundamental charge to the reservoir engineering profession. In recent years much quantitative assistance in evaluating field development programs has been provided by computerized techniques for predicting reservoir flow behavior. Because of the spatially distributed and dynamic nature of producing operations, automatic optimization procedures, such as those now in use for planning refining operations, are not now available for planning reservoir development. However, present mathematical simulation techniques do furnish powerful means for making case studies to help in planning primary recovery operations and in selecting and timing supplemental recovery operations. A number of methods have been reported which simulate the flow of one, two or three fluid phases within porous media of one or two effective spatial dimensions>-4 However, applying computer analyses to actual reservoirs have been limited mostly to two-dimensional areal or cross-sectional flow studies for two immiscible reservoir fluids. To obtain a three-dimensional picture of reservoir performance using such two-dimensional techniques, it has been necessary to interpret the calculations by combining somehow the results from essentially independent areal and cross-sectional studies. To the authors' knowledge, the only other three-dimensional computational procedure, in addition to those presented here, was developed by Peaceman and Rachford8 to simulate the behavior of a laboratory waterflood. Two computational techniques which may be used to simulate three-dimensional flow of two fluid phases are described in this paper. The first method, called the "three-dimensional analysis", employs a fully three-dimensional mathematical model that treats simultaneously both the areal and cross-sectional aspects of reservoir flow. The second method, called the vertical equilibrium (VE) analysis", is applicable

By W. N. Lacey, B. H. Sage

The results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of grave! screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. Introduction Gravel screens have been placed in water and oil wells for a number of yearsl,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. Influence OF Gravel Screens upon Productivity The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1942

By E. A. Gulbransen, W. S. Wysong

The behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a a Or as an important component in alloys in high temperature Oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a micro-balance study of the following problems: (1) the oxidation behavior in the ternperature range of 25 to 550°C (') the reduction with pure hydrogen Of thin Oxide films formed On tungsten, and (3) the volatility Of thin Oxide films On tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the Oxide to to ratio is greater than one, the oxide is not considered protective, ('1 the meta1 readily Oxidizes at temperatures from 30" to 55o°C (3) the oxides WO² and WO³ are reduced at temperatures as low as 500°C. by hydrogen, and (4) the Oxide WO3 is volatile at temperatures from 800 to 1100°C. Literature The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°c. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides, Schei14 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bed-worth's5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.? They have reported that WO3 is the stable oxide in contact with the metallic substrate up to approximately 600°C while wo³ forms first at 7oo°c. Hagg and Magneli8 have recently reported a study of the lattice structures . observed in the tungsten oxidcs using the X-ray diffraction method. In addition to an a-phase WO3 and a '-phase WO2, they reported the existence of two new phases. A 8' phase, homogeneous between

Jan 1, 1949

By David J. Mack, A. H. Kasberg

The transformation characteristics are found to resemble a similar binary alloy. The differences are due to the alpha iron particles. While strength properties of the isothermally transformed alloys are high, ductility is low, resulting in high notch sensitivity. The elastic modulus can be varied widely and correlates with strength. Abnormal grain growth sometimes occurs. A CONSIDERABLE amount of work has been done on the isothermal transformation of high purity aluminum bronzes using the methods pioneered by Davenport and Bain.' The first isothermal study of these alloys was made by Smith and Lind-lief,' but more recently Mack", " and Klier and Grymko5 have continued the work. In commercial aluminum bronzes, one or more elements are always added to refine the ß grain size and to improve the mechanical properties. The effect of these elements on the isothermal transformation has not been reported in the literature. No systematic study of the properties of isother-mally transformed aluminum bronzes has apparently been reported, although adequate information is available on their properties after more conventional heat treatments. The fact that a eutectoid alloy will reject face-centered cubic a during isothermal transformation at appropriate temperatures2'" warrants investigation of the properties of such structures. Another cogent reason for determination of properties is the fact that the modulus of elasticity of the eutectoid alloy varies widely with the nature of the heat treatment." Preliminary experiments7 indicated that a high purity eutectoid alloy would not give reproducible results in property determinations because of ex- cessive ß grain growth during heat treatment, a single ß grain frequently occupying the entire cross-section of a standard test bar. For this reason a commercial aluminum bronze containing iron as a grain growth inhibitor was used. The isothermal transformation diagram of the alloy was first determined. On this basis, the heat treatments necessary to produce representative structures were selected and the properties determined. Material A commercial alloy (Ampco Grade 20) of the following composition was used: Cu, 83.68 pct; Al, 12.31 pct; Fe, 3.68 pct; Ni, 0.28 pct; and Mn, 0.03 pct. This alloy proved to be very close to the eutectoid composition and may be compared with the accepted value of 11.8 pct A1 in the binary Cu-A1 system. Comparison is valid only because of the "negative replacement effect" of the iron? Since traces of excess y² are present, the alloy is slightly hyper-eutectoid. The material was received in the form of 3/4 in. round, hot extruded bars. Specimens of approximately ? in. thickness were cut from this stock and drilled to allow suspension in the salt bath. The structure of the as-received material varied from 5 to 40 pct a + y2* in a matrix of ß. The amount of a + y² present was dependent upon the ß grain size of the extruded material. The coarse grained portions did not form as much a + Y, as did

Jan 1, 1952

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By W. N. Lacey, B. H. Sage

THE results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of gravel screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. INTRODUCTION Gravel screens have been placed in water and oil wells for a number of years1,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. INFLUENCE OF GRAVEL SCREENS UPON PRODUCTIVITY The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the. average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized- spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1941

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By H. l. Burghoff, E. C. Bohlen

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants. IT must always be remembered, with regard to the problem of water-borne industrial wastes, that stream pollution from any cause is just one factor in the comprehensive problem of water supply in modern times. Industries nonexistent 25 years ago are now flourishing, and supplies of water piped to homes and apartments, as well as the greater number of plumbing fixtures per dwelling and per building, have created an ever growing demand on the country's water resources. Indication of this rapid growth in demand is shown in Table I, which is quoted from Abrams. of Texas increased 287% and the water consumption 7000 per cent." The domestic load varies greatly, depending on the extent of the available supply and the habits of the community. According to the report of the President's Water Resources Policy Commission' the United States Public Health Service reported a national average of 127 gal per capita per day, varying from 60 gal in communities of 500 persons to 140 or 150 gal in cities of 10,000 or over. Other critical areas may be cited to illustrate the inter-relation between new industrial processes and the demands for water in the area where the new enterprise is located. Powell and Wilson have pointed out that during World War 11, in the vicinity of Louisville, Ky., a rapid expansion of industry took place, consisting of numerous synthetic rubber plants. The demand for water increased from 37 million gal per day in 1937 to 62 million gal in 1943. These heavy requirements drew down the supply stored in the water-bearing aquifers to such an extent that urgent plans for recharging were considered. Similar situations have developed in the Los Angeles area and in the vicinity of Texas City. Warne4 has drawn attention to the situation in Los Angeles area, where in the West Basin the withdrawal of ground water in 1945 was 90,000 acre-ft, almost double the amount of the natural fresh water recharge. The draw down has been so severe that the level of the ground water is now below sea level, and sea water is invading the West Basin aquifers at rates up to 300 ft per year. In the Report of the Engineers Joint Council it is pointed out that in the area of Texas City the ground water table has been critically lowered. In 1930 the daily withdrawal from the water-bearing aquifer was 0.5 million gal. By 1945 the quantity withdrawn

Jan 1, 1954

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By John Mullen

Impingers TWO types of midget impinger apparatus are used at Climax. The Mine Safety Appliances Company's midget impinger (MSA) and the Climax Molybdenum Company's midget impinger (CMC) (Fig. I). The Leiman Brother's No. 25, positive displacement pump is used in the CMC impinger instead of the four-cylinder radial pump that is used in the MSA impinger. With the MSA apparatus it is possible to obtain the proper vacuum by adjusting the needle valve on the vacuum chamber, while with the CMC impinger the proper vacuum is obtained by varying the rate at which the pump is cranked. The Leiman Brother's No. 25 pump is built to displace 0.1 cu. ft. of air per min. when operated at 145 r.p.m. In the CMC impinger this pump is so geared that the required crank speed is approximately 59 r.p.m. Both types of impinger apparatus are equipped with a water gauge mounted on top of the case and they are calibrated and operated in reference to the gauge. The MSA impinger flasks and nozzles are used with both types. Calibrating Impingers A calibrated precision Sargent wet-test meter (Fig. 2) is used in calibrating the impinger apparatus. The apparatus is set up as for taking a sample in the field, except that the hose from the outlet side of the meter is attached to the impinger nozzle. One revolution of the large hand of the meter indicates 0.1 cu. ft. of air displaced. The impinger pump is cranked for one minute, therefore, at a rate that will cause the large hand of the meter to make one revolution. The gauge reading is noted, then the impinger is cranked at this rate for 10 min. and is checked for error. If the meter indicates that more or less than I cu. ft. of air has been displaced, the impinger must be cranked—ither slower or faster according to the error—for another 10 min. and again checked for error. This operation is repeated until the proper gauge reading for a sampling rate of 0.1 cu. ft. per min. has been determined. This gauge reading is used in all sampling operations until the impinger is again calibrated. An impinger is calibrated at least twice each week. MlCROPROJECTOR A Bausch and Lomb model B micro-projector is used (Fig. 3). It consists of a substantial metal base supporting the light source and a microscope. Illumination is provided by a Bausch and Lomb 4.5-amp. arc lamp with mechanical feed. A glass water cell filled with a heat-absorbing and color-filter solution is placed between the arc lamp and the microscope. Two types of solution have been found satisfactory— a 2 per cent solution of copper sulphate or a 2 per cent solution of picric acid and distilled water. This percentage may be varied to give the desired color to the light reflected upon the screen. Any standard microscope may be used. A Bausch and Lomb microscope with

Jan 1, 1946

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

THE solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels from well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approximately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and after some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sections are easily reworked, (4) low cost. CONSTRUCTION It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following procedure for those who contemplate the construction of such a model: I. Determination of the Scale.-Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to be used. 2. Construction of the Base.-A satisfactory base may be constructed by using two pieces of three-ply wood separated by strips of i by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Construction of the Frame (Fig. I).-In the construction of the frame the use of 1/2-in. o.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least I in. higher than the

Jan 1, 1941