Search Documents

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.', ' One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.' The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.'.' The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,' experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By Robert Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 4th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 3rd edition (1960) of Industrial Minerals and Rocks will clearly demonstrate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Re- view. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 3rd edition of Industrial Minerals and Rocks. Most of these, of course, are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 11th annual meeting in 1975, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the U.S. Geological Survey and the U.S. Bureau of Mines. The two agencies publish many reports and maps on a variety of geo- logical and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications. (New Publications of the Geological Survey, U.S. Geological Survey, Washington, D.C. 20242) and New Publications-Bureau of Mines, Publications Distribution Branch, U.S. Bureau of Mines, 4800 Forbes Ave., Pittsburgh, Pa. 15213). The U.S. Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, and 1970. Three other major series of publications by the Bureau are Information Circulars, Reports of Investigations, and Mineral Trade Notes. The latter is particularly good for news of foreign developments. A new Professional Paper No. 820 of the U.S. Geological Survey, 1973, summarizes data on the mineral resources of the entire country. The USGS, in cooperation with USBM, other Federal and various state agencies, has also prepared summary reports on mineral and water resources of given areas which include

Jan 1, 1975

By B. M. Larsen

A discussion based on three commercial furnace tests and electrical analogue calculations is presented. It shows that while regenerator efficiency is mainly dependent on loading or relative amount of heat exchange surface plus the heat transfer coefficients as effected by flow velocity, the actual air preheat temperature can be high or low, largely independent of regenerator efficiency, mainly due to the diluting or unbalancing effects of cold air leakage into various parts of the furnace system. THERE are many signs of a renewal of interest in the heat regeneration aspect of the open hearth process, among them being the recent paper by Marsh,' the introduction of auxiliary checkers in the stacks of the Isley furnace design, and a number of recent installations of two-pass checkers in new and old furnaces. However, there are also signs of yielding to the usual temptation of oversimplifying a problem. Faced with the job of obtaining better draft on a furnace, for example, a good designer always recognizes that focusing attention on some one factor, such as height of the stack or capacity of the exhaust fan, does not make his problem any easier; rather he must look at the whole system, including such items as valve resistances, bends in the flues, and flow resistance in the waste heat boiler; then he must make his design in relation to the available draft so as to avoid any serious bottleneck in the system. Yet this example is really much simpler than the problem of air preheating, and again, the latter problem is not really made easier by concentrating on air temperature in uptakes and on the more obvious methods for making this air as hot as possible. Also to be considered are such things as the total amount of air needed theoretically for complete combustion at any selected fuel rate, together with that needed for oxygen absorbed into the bath and for burning the combustible gases given out from the bath, plus some excess air. Furthermore, how does this total air requirement relate to the regenerator efficiency at various loadings? How much of the total air equivalent in stack gases will come from preheated air passed through the whole length of the incoming regenerator and how much from air leakage into various zones of the whole furnace system? Does the effect of leakage air differ depending on whether it leaks into the ingoing regenerator, the furnace above floor level, the outgoing regenerator, or the stack zone? Over a number of years we have in this Laboratory experimented with methods for measuring hot gas temperatures; we have measured, approximately, the efficiency of a few regenerators on commercial furnaces and we have developed an electrical analogue' for calculations of regenerator efficiency. The whole problem is too complex to cover in one paper even with a more complete background of data than we possess, but we can attempt here to clarify certain aspects in a general way, hoping to assist specific plant studies on individual furnaces. Some of our earlier experience has been incorporated into chaps. 4, 19, 20, and 21 in the book "Basic Open Hearth Steelmaking,"" and on the assumption that this text is available to most readers, this discussion has been shortened by references to that book. The most recent design of a flowing-gas thermocouple which we are now using for measurement

Jan 1, 1955

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By E. S. Lenker, H. J. Van Hook

A complete swies of solid solutions has been found between the compounds InAs and GaAs Below the solidus. The melting relations determined by differential thermal and static quenching technzques, indicate that the liquidus and solidus are of the simple ascendant type. No evidence of unmixing of the homogeneous solid solutions was observed at sub-solidus temperatures. A quenching method for locnting the solidus, using X-ray diffraction techniques, is described in some detail. THE semi-conducting properties of compounds formed by various combinations of the less familiar intermetallic elements have created an increasing interest in the phase relations in systems involving these elements. The complete phase diagram of such a system, containing a compound of special interest, will often provide information as to the most favorable conditions for preparing large crystals from a melt, as well as specifying the temperature stability of the crystalline phase or phases produced. In view of the current importance of gallium arsenide in semiconductor research and of the structural similarities of indium arsenide, it was thought that the complete phase relations of the system InAs-GaAs should be investigated. Previous work on the system Ga-As by Koster and homa' and on In-As by Liu and peretti2 has shown that GaAs and InAs are the only compounds formed, having melting points of 1238° and 942°C, respectively. In a survey of various systems of elements from groups IIIb and Vb, spengler3 also re- Mines Ltd., for his continuing encouragement and for permission to publish the results of this work. ports complete miscibility of gallium, indium, and arsenic in the liquid state. In a partial investigation of the InAs-GaAs system, Woolley and smith4 found extensive solid solution throughout the alloy range. Their subsolidus work, however, was inconclusive at temperatures below 900" and they did not determine the liquidus relationships of the system. PRESENT INVESTIGATION The starting materials used were high-purity gallium, indium, and arsenic. The method of preparation of the compounds follows that devised by M. Shafer and is described in detail in a paper by Shafer and eiser.' The end-member compounds, GaAs and InAs, were first prepared by reaction of the elements in the desired proportions in evacuated silica glass vials. The vials were rotated in a furnace as the temperature was slowly raised to insure rapid and complete reaction at low temperatures. Thereafter the starting materials, GaAs and InAs, were melted by heating the sealed vials to 1300" and 1000°C, respectively; the vials in this case were filled as completely as possible to keep the vapor space small and thereby minimize the loss of arsenic to the vapor phase. Ten binary mixtures of these compounds were then prepared by reaction of the powdered material in the solid state just below solidus temperatures. At 900C preparations containing 3, 5, 8, 10, 25, 35, 50, and 75 mol pct GaAs were found to be single homogeneous phases, indicating a complete series of solid solutions between GaAs and InAs. Moreover, it was discovered that the homogeneity of any crystalline binary preparation could be very accurately checked by X-ray diffraction because of the large differences in unit cell dimensions of the end membe5s. The cubic lattice constant ofor GaAs is a = 5.652A and that of InAs is a = 6.061A

Jan 1, 1963

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

By J. L. Thompson

There are two basic forms of the LPG-slug process: the gas driven and the water driven. The pressure required for miscibility between gas and LPG prohibits the use of the gas-driven LPG process in shallow reservoirs. The water-driven LPG slug process normally exhibits good sweep efficiency. However, displacement of the LPG by water is poor. An improvement in this process appears possible by injecting a slug of carbon dioxide between the LPG slug and the water drive. Laboratory experiments were conducted in homogeneous linear systems to determine the effect of pressure on the various displacement zones. In the carbon dioxide-LPG displacement zone, the effect of pressure on the displacement efficiency is negligible above the miscibility pressure. However, the displacement efficiency decreases linearly with decreasing pressure below the miscibility pressure. With water displacing carbon dioxide, it was found that the recovery of carbon dioxide after water breakthrough can be predicted from its solubility in water. A displacement test was conducted with LPG and carbon dioxide slugs large enough to avoid interference between the oil-LPG, LPG - carbon dioxide and carbon dioxide - water displacement zones. Under these conditions, essentially complete oil and LPG recovery was obtained. However, a substantial amount of carbon dioxide was left in the core at water breakthrough. INTRODUCTION It has been shown in homogeneous linear systems that essentially complete oil recovery can be obtained by displacement with a miscible fluid such as LPG. Economic considerations dictate that the valuable LPG also be recovered. Methods proposed for recovering the LPG include (1) displacement with natural gas at a pressure high enough to make the two fluids miscible1 (the disadvantage of this method is that the required pressure of about 1,500 psi is too high for shallow reservoirs) and (2) displacement of the LPG with water2 (principal disadvantage is that a large amount of LPG remains in the formation because of poor displacement efficiency). This paper treats an improvement in the water-driven LPG slug process3,4 where carbon dioxide is injected between the LPG and water. Carbon dioxide is completely or at least partially miscible with propane and soluble in water; thus, displacement efficiency is improved at both ends of the carbon dioxide slug. To minimize effects of other variables, all experiments were conducted in linear core systems. GENERAL PROCESS DESCRIPTION The displacements of propane by carbon dioxide and carbon dioxide by water are considered separately, assuming enough of each is injected to prevent mutual interference. Displacement descriptions are confined only to the part of the pore volume containing mobile fluids unless otherwise specified. The schematic representation is given in Fig. 1. Starting at the producing well, a zone containing only oil is followed by a zone containing a single-phase mixture of propane and oil. The concentration of propane increases in the direction of the injection well and ultimately grades to pure propane. Then follows a zone containing a mixture of propane and carbon dioxide in continuously varying proportions until 100 percent carbon dioxide is reached. In this zone, the concentration of carbon dioxide in the immobile water phase also varies from zero to full saturation. Whether the displacement of propane by carbon dioxide is of complete or partial miscibility depends on pressure and temperature (Fig. 2). If the horizontal line representing the prevailing pressure intercepts the boundary curves of the phase envelopes for the prevailing temperature (i.e., if the pressure is lower than the critical

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940's it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By A. J. Opinsky

ThE superior performance of nonsag tungsten wire in lamps has been ascribed to the large-grained micro-structure that can be developed in it. The orientations of these large grains have been studied several times; most published data1-' appear to be similar to those plotted in Fig. 1. These new data were obtained by X-ray back-reflection Laue technique from all of the large grains occurring in thirteen different wires that had been heated at the lowest possible temperature for the formation of large grains. Here the wire axis is plotted in terms of the principal directions of the cube. Rosi decided that the preferred orientation of the large crystals could be described by a single ideal orientation, (531), being parallel to the wire axis.' Rieck2,3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Seigle argued that the data suggest that (211) is parallel to the wire axis instead of a single ideal orientation.5 This {211} contains the (531) ideal orientation and would appear to be a more general case. Ahlborn and Wassermann report that their orientation data stretch from ( 110) through (531) to (311) 8 This is part of the locus of (211). All these investigators have determined the orientations of the large grains by back-reflection Laue techniques. They have all obtained essentially similar results. On the other hand, Swalin and Geisler, who obtained their data by neutron diffraction, indicated that the preferred orientation of the large grains in doped wire is (110) .7 These findings cannot presently be reconciled with the pole density data described in the previous paragraph. Rosi1 and Rieck2 have advanced arguments about how their orientations could occur. Nevertheless, the crystallographic link between the (110) (cold-worked) fiber texture and the preferred orientation of the large grains has remained missing. This link can be provided through the concept of coincidence-type boundaries. Such boundaries separate two grains that have a certain number of common lattice sites. Coincidence relationships that result from rotations about low index directions are given by Brandon et a1 .' What is desired is a calculation of those orientations that bear a coincidence relationship with the (110) fibers of the cold-worked matrix. This situation arises in the following fashion. Heating the tungsten wire for a combination of time and temperature falling short of the formation of the nonsag structure yields a structure that is still fibrous in nature and the preferred orientation remains (110). During grain growth, the growing grain is in contact with these fibers. It is hence possible that the entire process may begin by the passage of a coincidence boundary into a (110) fiber. The calculations were carried out analytically and checked graphically. Following Brandon et a1.,8 coincidence relationships from 1 in 5 to 1 in 19 have been considered. The results of the calculations are given in Fig. 2. Of the coincidences examined, some of those occurring upon rotation about ( 110) come closest to the experimental points in Fig. 1. Nineteen of the twenty-three data points in Fig. 1 can be attributed to the ideal orientations A, B, C, and D in Fig. 2. As determined analytically, three crystals lie within 4 deg of point A, four lie within 21/2 deg of point B, eleven lie within 5 deg of point C, and one lies within 1 deg of point D-a total of nineteen. The off-lying points are near the |110| point of the triangle.

Jan 1, 1968

By W. A. Tiller, D. H. Lane

A simple zone melting technique for investigating the effect of ultrasonic irradiation upon ingot solidification is described. The effect of i) ultrasonic power level, ii) freezing velocity, iii) constant or variable frequency, iv) direction of irradiation, and v) transducer-cozlpling bar joint upon the grain size of type 316 stainless steel have been investigated. The results of this study support the postulate that the ultrasonic vibrations increase the nucleation probability in the layer of liquid adjacent to the freezing interface. In the first paper of this series,l the possible mechanisms whereby ingot structure may be altered by irradiating a solidifying melt with ultrasonic vibrations have been discussed. A new technique for efficiently introducing the ultrasonic energy into the solid-liquid interface region was presented and applied to ingot preparation by the consumable-electrode arc-melting technique. The experimental results support the postulate that the ultrasonic vibrations may refine the ingot structure by increasing the nucleation probability in the zone of liquid adjacent to the solid-liquid interface. The present paper describes the application of the same technique to a relatively simple laboratory-scale zone-melting apparatus. This apparatus is found to be well suited to the detailed study of ultrasonic technology in this area and allows one to determine, in particular, the minimum ultrasonic power level needed to produce a certain grain size in a particular material. The results of this study support the nucleation mechanism for grain refinement, but do not provide any deeper insight into the specific nucleation mechanism responsible for the effect. EXPERIMENT The apparatus used in these experiments is shown in Fig. 1 and illustrated schematically in Fig. 2. The material to be studied, type 316 stainless steel, was in the form of a 3/4-in. sq bar 30 in. long. This bar was placed in a square open-topped mold with open ends made from high-purity graphite coated with a flame-sprayed Al2O3, skin. Surrounding the crucible was a molybdenum susceptor with 3/8-in. diam holes spaced at 1-in. intervals along its length to serve as sight ports. A tapered transducer horn was brazed to one end of the specimen. The entire assemblage was enclosed in a quartz tube, the transducer itself projecting out one end and resting in a cooling tank. A vacuum seal between the coupling bar and the end plate enclosed one end. A similar plate and seal enclosed the other end. The system is gas tight and can be operated under vacuum or an inert atmosphere. For these experiments, flowing argon at 15 in. of Hg pressure was used. The heat source for melting the stainless steel specimen was a 2-in. long 3-kc induction coil placed around the quartz tube; this source heated the susceptor, inductively melting about a 3-in. zone of the sample by radiation. To move the molten zone at a specified rate, the induction coil was moved down the tube at this rate with the aid of a simple pulling device. Thus, the sample could be irradiated at varying ultrasonic frequencies and power levels and could be solidified at varying rates. The power input to the transducer was measured using a "John Fluke Model 120 VAW-Meter." 1 The power delivered to the interface region is probably only about 50 pct of that measured on the VAW-meter. In a typical run, when the ultrasonic power was turned on, the interface of the molten zone closest

Jan 1, 1961

By L. K. Nemeth, H. T. Kennedy

The investigation presented in this paper was performd to develop a relationship between the dewpoint pressure of a hydrocarbon reservoir fluid and its composition, temperature and characteristics of the heptanes-plus fraction. This is part of an over-all program to develop correlations for the essential properties of reservoir fluids with the composition, temperature and pressure. In all, 579 dewpoint pressures, determined experimentally on 480 different condensate systems along with their compositions and temperatures, were obtained from the literature and from previously unpublished sources. Compositions were expressed in terms of mol fractions of methane through heptanes-plus, nitrogen, carbon dioxide and hydrogen sulfide, and the molecular weight and specific gravity of the heptanes-plus fraction. Distribution of the samples assured a good representation of most of the major oil-producing areas in the world. A multiple regression analysis program written for the IBhl 7094 digital computer was used to compare numerous equations and to calculate their coefficients. The final equation containing 11 coefficients resulted in an average absolute deviation of 7.4 percent for all the samples. Segregation of data on the basis of one or more variables did not materially improve the results. The correlation developed is useful in predicting the dewpoint pressure of condensate reservoir fluids from variables normally measured in the laboratory. INTRODUCTION In any discussion of the dewpoint of hydrocarbon mixtures, it should be noted that there are two kinds of dewpoints which must be distinguished. The first type, or normal dewpoint, usually occurs at low pressures as dry gas is compressed to the point where liquid first forms. The second type, sometimes called the retrograde dewpoint, occurs when a gas mixture containing heavy hydrocarbons in solution is depressured until a liquid is formed. The first type, as applied to condensate mixtures, would normally be below atmospheric pressure and would be of no interest in reservoir performance. The second type is of great significance in interpreting reservoir behavior and is the property referred to throughout this paper. Laboratory measurement of dewpoints is laborious, expensive and subject to many errors, and it is desirable to find a reasonably accurate method to predict dewpoint pressures from the composition and other readily available properties normally measured on the fluids. A possible method of calculating dewpoint pressures would be to employ a set of equilibrium ratios (K-values). 1 However, the K-values themselves depend on composition as well as temperature and pressure; presently their use adds nothing to the accuracy of predicting dewpoints. If future correlations provide a significantly better method of estimating K-values for heavy hydrocarbons, they may be of greater use. REVIEW OF LITERATURE In 1944, Olds, Sage and Lacey 2 studied the behavior of fluids from the Paloma field. Properties of seven mixtures were studied at temperatures ranging from 100 to 250 F and at pressures up to 5,000 psia. From the information obtained, the influence of composition and temperature upon the dewpoint was determined. It was found that removal of the intermediate molecular weight components from the mixture resulted in considerable increases in the dewpoint pressures. Results indicated that the effect of changes in temperature was relatively minor when compared with the effect of modifying the mixture by removing the intermediate components. Thus, removal of propane and butanes resulted in an increase in dewpoint pressure more than 10 times greater than a change in temperature from 100 to 250 F. The authors stated that althouah

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

By D. N. Seidman

In the course of a study of the electronic and thermodynamic properties of Pb-Se alloys it was found necessary to have an accurate knowledge of the phase diagram. However, the literature is in disagreement as to whether or not a monotectic reaction occurs in the lead rich portion of the phase diagram. Pelabonl reported only a two-phase region consisting of lead-rich liquid and solid PbSe extending from almost pure lead to the compound PbSe, and gave the melting point of PbSe as 1065°C. The data of Friedrich and Leroux2 are in general agreement with this type of diagram, with the melting point of the compound being 1088°C. However, Nozato and Igaki by inverse rate thermal analysis observed a monotectic reaction isotherm exlacing at 860°C with a monotectic composition of 20.5 at. pct Se. The miscibility gap in the liquid state extends from 7.5 to 20.5 at. pct Se. Hansen and Anderko4 accepted Nozato and Igaki&apos;s phase diagram in the region of the lead-rich monotectic. To reinvestigate this portion of the phase diagram, both thermal analysis and metallographic examination of various compositions were performed. The thermal analysis apparatus was constructed according to the specifications of the National Bureau of Standards. A t/t-l pct Rh thermocouple was calibrated against the melting point of copper (NBS), zinc (NBS), and antimony (A. D. Mackay), the emf being measured with a Rubicon Type B potentiometer sensitive to lpv. The absolute accuracy of the thermal analysis obtainable with this system is ± 0.5oC. Starting materials were semiconductor grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999 pct pure with only trace impurities detected upon spectroscopic examination. One hundred galloys were sealed in quartz crucibles with a central thermocouple well under a vacuum of less than 1 p. This procedure prevented any composition change due to vaporization during the run. Cooling curves were obtained on the alloys listed in Table I. Data was taken by the direct method at cooling rates ranging between 1/2 to 2°C per min. The alloys were heated well above the liquidus and shaken vigorously to insure homogeneity. No evidence of an arrest indicative of the monotectic reaction was observed, and the two-phase region reported by Pelabonl and Friedrich and Leroux? was confirmed in general, although our data give higher liquidus temperatures than Friedrich and Leroux. The melting point of stoichiomet-ric PbSe determined for two different samples was 1080.7 0.5oC. The results of this investigation are compared with Nozato and Igaki&apos;s data in Fig. 1. To Complement the thermal analysis data, an 86 at. pct Pb specimen was examined microscopically. This composition was in the center of the miscibility gap reported by Nozato and Igaki.3 The alloy was heated to 1000°C, held for 1/2 hr, and water quenched. The specimen was polished using standard metallographic techniques for lead. The alloy was etched with an acetic-nitric acid etchant for 10 min at 45°C. Microscopic examination did not indicate the existence of two separate layers or solidified droplets imbedded in a matrix, as would be expected if a miscibility gap were present. The mi-crostructure shown in Fig. 2 consists of uniformly dispersed, dendritic PbSe in a lead-rich matrix.

Jan 1, 1962

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

NITROGEN is becoming recognized as one of the important elements in ferrous physical metallurgy. Several investigations indicate that nitrogen plays a significant part in such phenomena as strain aging and temper brittleness. Nitrogen is known to be a powerful austenite stabilizer and may be a useful alloying element in stainless steels. The hard-enability of steels has been found to be increased by nitrogen. The nitriding and carbonitriding pro- cesses are examples of successful industrial application of nitrogen in ferrous materials. For a complete understanding of the various roles played by nitrogen in ferrous metallurgy a knowledge of the phase relations in the binary iron-nitrogen system is essential. The literature contains a variety of iron-nitrogen phase diagrams. Those suggested by Fry, Sawyer,² Epstein and his coworkers,³,4 Lehrer,5 Eisenhut and Kaupp, and Hägg7,8 differ significantly from one another. Moreover, the most recent of these investigations dates back about twenty years. A re-determination of the entire diagram, therefore, appeared desirable. In addition to the published phase diagrams, investigations have been carried out on portions of the iron-nitrogen system. Bramley and Haywood determined the composition and temperature of the iron-iron nitride eutectoid. The maximum solubility of nitrogen in a iron was investigated by Portevin and Seferian10 and by Diikstra. 11 Several investigators have determined the crystal structure of the various iron-nitrogen phases. In fact, Eisenhut and Kaupp6 and Hägg7 based their entire phase diagrams on the results of such studies. Epstein&apos; and Emmett12 reported lattice-parameter measurements on the E (hexagonal close-packed) phase. Osawa and Iwaisumi13 also studied the change in lattice parameters of the a, ? and E phases with nitrogen content. Brill" and Hägg7 showed that the y&apos; phase has an ordered structure, and Hendricks and Kostingsl5 suggested a structural relation between the E and phases. In a recent investigation Jackl6 arefully studied the super-lattice reflections from the y&apos; and phases. Experimental Procedure A large variety of experimental methods has been used by previous investigators in studying the iron-nitrogen system. These methods include thermal analysis, microscopic examination, X ray diffraction, magnetic measurements, dilatometric analysis and anelastic experiments. Thermal analysis is of low accuracy in determining changes in the solid state. This accuracy is further decreased for iron-nitrogen alloys since composition changes will occur during heating or cooling unless extreme care is taken to use a proper atmosphere. Metallographic methods are of small value . because homogeneous iron-nitrogen alloys of sufficient size can be produced only with great difficulty. The dilatometric method is open to the same objections as thermal analysis in that changes in composition may occur during heating and cooling. Lattice parameter measurements by X ray diffraction can be used satisfactorily for determining phase boundaries if cooling is fast enough to prevent structural changes. In view of the limitations of the various other techniques two methods only were adopted in this investigation, (1) X ray diffraction measurements, and (2) a controlled nitrogenizing method. The second method is an innovation for investigating the iron-nitrogen system, and will be described at length. Materials: All iron-nitrogen alloys were prepared from carbonyl iron powder of the analysis shown in table I. The average particle size was about 20

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen&apos; and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951