Search Documents

By M. J. Pool, P. J. Spencer, R. V. Miner

The partial molar heat of solution of rhodiunz in liquid lin and Rh-Sn alloys has been measured as a function of rhodium concentration at 700" , 725" , 750" , and 775°K. The values at infinite dilution are very exo thermic, ranging from -29,950 to -28,260 cal per g-atom Rh at 700" and 775"K, respectively. At the solubility limit the heat of solution becomes sharply nzore exothermic and has permitted the liquidus boundary to be accurately established at each temperature. From the measurements in the two-phase region of liquid Plus RhSn, the heat of formation of RhSn,has been determined. A large increase in the heat of formation between 725" and 750°K suggests the possibility of a phase transformation in this compound. V ERY few measurements have been made of the heats of solution of transition metals in liquid tin; yet those values that are available are of great interest because of their very large exothermic nature. For example, the heat of solution at infinite dilution of palladium in tin has been measured as about -26,000 cal per g-atom (625" to 800°~),' while the heat of solution at infinite dilution of platinum is even more exothermic at -28,591 cal per g-atom (914°K).' These values are of the same order of magnitude as the heat of formation of many intermetallic compounds and as such clearly indicate that very strong bonding must exist between the solute and tin atoms in the liquid solutions. Rhodium might be expected to display similar solution characteristics in tin in view of its close electronic resemblance to palladium and platinum. Since no thermodynamic data are available for Rh-Sn alloys, rhodium was chosen as an appropriate solute for further investigation of transition-metal systems with highly exothermic heats of solution at infinite dilution. EXPERIMENTAL The heat of solution of rhodium in dilute Rh-Sn liquid solutions was measured as a functlon of rhodium concentration at 700°, 725", 750°, and 775°K. The liquid-metal solution calorimeter used in this work has been fully described elsewhere. At the start of each series of measurements, the solvent bath consisted of about 0.5 g-atoms of 99.9+ pct pure tin. To this was made a number of small rhodium additions, about 0.0005 g-atoms each, and the heat of solution was measured for each. Rhodium of 99.9+ pct purity in powder form was used in order to promote rapid dissolution in the liquid tin. The powder specimens were contained in tin foil stated to be purified (lead-free). This foil was found to have no measurable heat of solution in pure tin so the effect of any impurities could be neglected. The energy equivalent of the calorimeter was experi- mentally determined by dropping tungsten and/or tin specimens at intervals during each series of rhodium drops. The tungsten and tin used were 99.95 and 99.999+ pct pure, respectively. The only heat effect due to a tungsten drop, or a tin drop at low rhodium concentrations in the bath, is the sensible heat of the specimen. The heat content of these materials is well-established and is presented in the compilation of Hultgren et al. 4 As the rhodium concentration in the tin bath increases a small heat effect arises from the reaction: Sn (liquid, T) — & (soln, T) where T is the temperature of the tin bath. Where necessary, this heat of solution of tin was determined by Gibbs-Duhem integration, and corrections were made to the heat effect of the tin calibration specimens and the tin foil containing the rhodium specimens. RESULTS AND DISCUSSION The calculated values of the heat of solution of rhodium in dilute Rh-Sn alloys as a function of composition are shown graphically in Fig. 1. The values have been corrected for the sensible heat of the specimens, initially at 273"K, and apply to the reaction:

Jan 1, 1969

By S. Weinig, E. S. Machlin

IN a previous study of the grain boundary stress relaxation phenomenon,' the authors had arrived at the conclusion that two successive steps were involved in the complete relaxation of stress at a grain boundary. These two steps were grain boundary migration and grain boundary slip. It was further suggested that the slower of these two processes is rate controlling. In an attempt to ascertain the validity of the above, a study of grain growth kinetics on the same alloys used for the previous study was undertaken. Separate wire specimens, 0.030 in. diam, in the same as-deformed state (99 pct reduction in area) as in the previous investigation were heated to the various temperatures for a sequence of times. The compositions used and the temperatures of testing are summarized in Table I. A statistical determination of grain size was then made on each specimen, using the average length of traverse between boundaries as a measure of the grain size. Examples of typical results obtained are shown in Figs. '1 and 2. The grain growth law D = ktn was found to fit most of the data. Using this relation, values of the grain growth exponent n were calculated and the inter -esting dependence of n on solute content shown in Figs. 3 and 4 was then obtained. Also, it was found that the constant K which was obtained from extrapolation is roughly independent of solute content. (K is uncertain to within ±25 pct.) An estimate of the activation energy for grain growth was made using the technique of Burke? This method utilizes the plot of the reciprocal of time necessary for the grain size to increase from a definite starting size Do, to a final size D, for each isothermal heat treatment. The slope of this curve corresponds to the heat of activation for the process. In Fig. 5 the rate of grain growth is plotted against the reciprocal of absolute temperature. The activation energies were obtained from these curves and are summarized in Fig. 6. Discussion It is interesting to note that the same saturation in the variability with concentration has been found for the grain growth exponent n in this research as was found in the previous researches on both grain boundary stress relaxationa and internal friction of dislocation origin." The significant feature is that saturation in the variation of these properties has been found to occur at about the same level of solute concentration, namely, between 0.1 and 0.5 atomic pct. The only characteristic common to these different quantities is that solute adsorption at grain boundaries and dislocation can take place and affect these values in a similar fashion. Thus, it is concluded that the grain growth exponent n depends upon solute adsorption at the grain boundaries. It appears, therefore, that theoretical considerations leading to the contrary conclusions5,6 have not treated the real process by which solute atoms exert their effect on grain growth. Prior to the analysis of the observed activation energies, certain of the aspects of the aforementioned grain boundary stress relaxation investigation will be briefly reviewed. It was found that with the addition of solute atoms the grain boundary stress relaxation peak (internal friction vs temperature) decreased in intensity. Simultaneously a second peak was observed which increased with increasing solute atoms. Both of these peaks were shown to be the result of grain boundary stress relaxation. They have been termed, respectively, poire peak and solute peak. It was suggested that the solute peak was dependent upon grain boundary migration, whereas the pure peak was a manifestation of grain boundry slip. Activation energies for both peaks were obtained as a function of Solute content. The value of the activation energy in the temperature range corresponding to the solute peak was

Jan 1, 1958

By B. Haimson, C. Fairhurst

A criterion is Proposed for the initiation of vertical hydraulic fracturing taking into consideration the three stress fields around the wellbore. These fields arise from (1) nonhydrostatic regional stresses in earth, (2) the difference between the fluid pressure in the wellbore and the formation fluid pressure and (3) the radial fluid flow through porous rock from the wellbore into the formation due to this pressure difference. The wellbore fluid pressure required to initiate a fracture (assuming elastic rock and a smooth wellbore wall) is a function of the porous elastic constants of the rock, the two unequal horizontal principal regional stresses, the tensile strength of the rock and the formation fluid pressure. A constant injection rate will extend the fracture to a point where equilibrium is reached and then, to keep the fracture open, the pressure required is a function of the porous elastic constants of the rock, the component of the regional stress normal to the plane of the fracture, the formation fluid pressure and the dimensions of the crack. The same expression may also be used to estimate the vertical fracture width, provided all other variables are known. The derived equations for the initiation and extension pressures in vertical fracturing may be employed to solve for the two horizontal, regional, principal stresses in the rock. INTRODUCTION Well stimulation by hydraulic fracturing is a common practice today in the petroleum industry. However, this stimulation process is not a guaranteed success; hence, the deep interest shown by the petroleum companies in better understanding the mechanism that brings about rock fracturing, fracture extension and productivity increase. Geologists and mining people became interested in hydraulic fracturing from a different point of view: the method may possibly be employed to determine the magnitude and direction of the principal stresses of great depth. Numerous articles in past years have dealt with the theory of hydraulic fracturing, but they all seem to underestimate the effect of stresses around the wellbore due to penetration of some of the injected fluid into the porous formation.1-4 Excellent papers on stresses in porous materials due to fluid flow have been published5,6 but no real attempt has been made to show the effect of these stresses in the form of a more complete criterion for vertical hydraulic fracturing initiation and extension. This paper is such an attempt. ASSUMPTIONS It is assumed that rock in the oil-bearing formation is elastic, porous, isotropic and homogeneous. The formation is under a nonhydrostatic state of regional stress with one of the principal regional stresses acting parallel to the vertical axis of the wellbore. This assumption is justified in areas where rock formations do not dip at steep angles and where the surface of the earth is relatively flat. This vertical principal regional stress equals the pressure of the overlying rock, i.e., S33 = —pD, where S33 is the total vertical principal stress (positive for tension), p is average density of the overlying material and D is the depth of the point where S33 is calculated. The wellbore wall in the formation is considered to be smooth and circular in cross-section. The fluid flow through the porous elastic rock obeys Darcy's law. The whole medium is looked upon as an infinitely long cylinder with its axis along the axis of the wellbore. The radius of the cylinder is also very large. Over the range of depth at which the oil-bearing formation occurs, it will be assumed that any horizontal cross-section of the cylinder is subjected to the same stress distribution, and likewise that it will deform in the same manner. STATE OF STRESS PRIOR TO DRILLING OF WELLBORE At a depth D from the earth surface within the oil-bearing strata, it is assumed that the following are 1References given at end of paper.

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By U. Andres

U. Andres (The Technion, Haifa, Israel)-The authors are to be congratulated on their research, new and interesting, in a field which, however, the present writer and his assistants have been trying since 1962 to bring to the attention of the scientific and technical world, by means of publications covering several different aspects of this many-sided problem. We announced, in these publications, the results of magneto-hydrostatic (MHD) separation of magnetic and nonmagnetic minerals which we made in magnetic fluids (in paramagnetic solutions and suspensions of magnetic particles) which interact with permanent" and impermanent" inhomogeneous magnetic fields. There is no doubt that the authors have succeeded in creating ferrimagnetic colloids made by dispergation of 10-30 wt % of magnetite in kerosene in the presence of 7-10 vl % oleic acid. It may be judged by [Figs. 3 and 4] that the suspensions represent great stability systems and also "hysteresisless" fluids [(Fig. 5)] which bear witness to the existence of superparamagnetic suspensions. If the viscosity of these colloids is not so high, and the cost of preparing them can be covered, the fluids which have here been received can possibly be of interest to the technology of mineral separation. The potential possibility and technological perspective of similar media is demonstrated in our joint work with G. Bunin18 in 1965. The research carried out on the pushing out of cylinders and spheres from magnetic fluid is impressive; it would, however, have been interesting if the authors had compared their results with those on the pushing out of bodies from magnetic fluids adduced from our work." In my books" there happens to be described an experiment on the pushing out of a sphere in magnetic wedge field, in which the pushing out force of suspension with 5 vl % of magnetite reached 125 g per cc. This testifies to interesting possibilities of these media. Our works' shows also, on the basis of Laplace's equation the receiving of an interesting distribution of pushing out forces by selection of corresponding configurations of magnetic poles. Objection must be made to the authors' introduction of the term "antigravity force." The direction of this force does not depend on the direction of the gravity force and their opposition, i.e., antigravity is only one particular case. I am in full agreement with the authors' statement that magnetic pushing out forces "can be utilized to separate nonmagnetic objects according to variations in their densities." It is, however, necessary to make only one important addition, which can be found in our research on MHS at the Technion in Haifa, namely, that magnetic fluids in magnetic fields can be utilized in the separation of minerals according to variations in their magnetic susceptibility. The authors' conclusion is especially important considering the fact that in our publications" (including one in English") some designs of MHS separators and some technological results received on MHS-separators have already been described. S. E. Khalafalla and G. W. Reimers (Authors' Reply)We were aware (mostly through Chemical Abstracts of the American Chemical Society) of the use of solutions of paramagnetic salts such as manganous sulfate in agnetohydrodynamic separations by the Russian school headed by G. Bunin."n Professor Andres' contributions to this school are also evident in his application of the ponderomotive forces in an electrolyte placed in electric and magnetic cross-fields to separate coal and other useful minerals." It must be realized, however, that the foregoing research by Bunin et al." involved the use of magnetic fields and field gradients of very large magnitudes, i.e., such that H • grad H - 101 Oe2 per cm. The magnetization of paramagnetic salt solutions range from 0.1 to 0.5 gauss (at fields of a few thousand Oersteds) and never reach saturation. The magnetization of our superparamagnetic ferrofluids ranges from 100 to 500 gauss and reach saturation at fields of a few hundred Oersteds. Hence, to effect the same separation, the quantity "H

Jan 1, 1974

By David E. Jones, Dean K. Hunt, C. Y. Chen

INTRODUCTION Of all the numerous geological hazards that threaten the well-being of urban areas in the United States, probably none is so widespread, persistent, and diversified as surface subsidence (HRB-Singer, Inc., 1977). Simply defined, subsidence is the vertical displacement or sinking of the ground surface caused by either natural phenomena or man's activities. The downward movement, however, can be accompanied by horizontal movement, strain, tilt and even by a locally upward movement. Damage to structures and the environment can result from any of these movements. Extracting subsurface materials, fluids and solids, accounts for most man-induced subsidence in the United States. Among all the mining-related subsidences, the collapse of voids created by underground coal mining has been the major cause in inflicting surface damage (Comptroller General of the United States, 1979). Subsidence from coal mining may occur within a few weeks or be delayed for years, depending upon the mineral layer's depth below the surface, the overlying rock strata's characteristics, the extent and methods of mining that were employed, and the time deterioration of pillar and mine structure. Unless underground resources are not mined or control measures are implemented to prevent or minimize damage, some degree of surface subsidence and its accompanied deleterious effects are often inevitable. The ways to control the subsidence and minimize surface damage may include: 1. Precautionary measures built into new structures or surface features. 2. Preventive works applied to existing structures or surface features. 3. Mine design incorporating special underground layouts. 4. Any combination of the above measures. Upon the enactment of Public Law 95-87, the Secretary of the Interior, through the recently created Office of Surface Mining (OSM), was authorized to promulgate rules to regulate mining reclamation including subsidence control. Proposed on September 18, 1978, these rules were finalized, following public comment and hearings, on March 13, 1979, as part of the permanent regulatory program for the regulation of surface mining and reclamation operations which include the surface effects of underground mining. On January 28, 1981, Secretary Watt of the Department of the Interior issued an order to re- quire all agencies to identify with recommendations all regulations which are believed to be excessive, burdensome or counterproductive. Also on February 17, 1981. President Reagan issued Executive Order No. 12291 requiring all Federal agencies to conduct a regulatory review to make a determination that each promulgation of a regulation is clearly within the authority delegated by law and consistent with Congressional intent (Federal Register, 1981). As a result, OSM initiated the regulatory reform to revise the permanent regulatory program. Following a brief discussion of the technical aspects and the effects of subsidence on man and his environment, this paper presents a historical overview of how rules and regulations are used to govern the subsidence related problems. The development of the regulation of subsidence under Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act) are also discussed, including the new regulations being developed under the regulatory reform program. SOME TECHNICAL ASPECTS Am EFFECTS OF FINE SUBSIDENCE An extensive historical review of mining subsidence is given by Zwartendyk (1971) and Shadbolt (1978). Comprehensive technical presentations have been given by Henry (1956), King and Whetton (1957), Hall and Orchard (1963). Muller, et al. (1968). Grard (1969), Voight and Pariseau (1970). Kapp and Williams (1972), Cummins and Given (1973), Brauner (1973) , and NCB (1975). A theory of surface subsidence due to underground mining was perhaps first fundamentally stated by a French engineer, Toillez, in 1838, and formulated by a Belgian engineer, Gonot, in 1839 (Goldreich, 1913, cited by Zwartendyk, 1971). Since that time,

Jan 1, 1982

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By B. H. Caudle, R. L. Slobod, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.' These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.'! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By R. L. Slobod, B. H. Caudle, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.' These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.'! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By J. Geertsma

The relationship between porosity and the speed of propagation of acoustic waves in fluid-saturated porous rocks as measured by the Sonic log and by ultrasonic tecbniques is analyzed. Biot's continuum theory 1 is used to explain the difference in acoustic wave propagation between a dry and a liquid-saturated porous material. The porosity is a variable in this theory. However, the acoustic wave propagation in the dry rock depends too on porosity, and this dependence is not predicted by the theory. Frequently in dry sandstones, a nearly linear relationship between reciprocal acoustic wave velocity and porosity is observed in the low-porosity range. The physics behind this behavior is outlined. An empirical relationship of the form, 1/v = A + F, applies accordingly for many porous dry rocks, provided the porosity is the only variable. The presence of a liquid in the pores changes the value of B, and this change is found to be in agreement with the Biot theory. The time-average relation introduced some years ago2 results in an equation of the same type — 1/V = F/Vf + (1 - F)/Vr — but is not based on a sound physical picture. Still, this relation sometimes predicts approximately correct A and B values. Carbonate rocks with their complicated pore structures sometimes show a different relationship between wave velocity and porosity, unfavorable for log interpretation. Examples are presented. The simultaneous presence of calcite, dolomite and anhydrite, with their different grain densities and matrix compressibilities, complicates acoustic-log interpretation in carbonate rocks still further. Other complicating effects of acoustic-log interpretation are discussed. They are related to the influence of shale streaks and natural fractures on the average wave velocity observed by the logging tool and to the effect of adsorption phenomena on wave propagation in unstressed rocks particularly in sandstones. INTRODUCTION The velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity loggers of various d-sign may be used, for which velocity is defined as the. distance between a wave generator and a wave detector (one-receiver system) or the distance between two wave detectors (two-receiver system), divided by the shortest time required for a vibrational pulse to cross this distance. Velocity loggers ale used to assist in seismic prospecting, to differentiate between the various types of sedimentary rock layers, and also to determine rock porosity and pore fluid content. This paper is especially concerned with the relation between velocity and porosity and the effect of the pore fluid. Most velocity-log interpretation in terms of porosity is based on a formula advocated by Wyllie, et al,2 suggested earlier by Hughes and Jones,3 and known as the "time-average relation". This formula app1ies for a model consisting of a layered system of parallel alternating slices of a solid and a liquid, crossed by the wave path perpendicular to the interfacrbs. This must be an unsuitable model for the derivation of wave propagation properties of liquid-saturated porous media. It suggests that only rock matrix and fluid properties influence the wave velocity. The surprising fact, nevertheless, is that applications of this formula to clean sandstones under specific conditions (sufficient effective stress) results in porosity predictions which are close to reality. Other authors, such as Gassmann,4 White and Sengbush,5 Brandt,6 and Hicks and Berry,7 make use of more realistic models to arrive at a wave velocity formula for porous sediments. Their models consist of various liquid-saturated packings of frictionless spherical grains and are, therefore, also highly idealized. A number of experimental results obtained in the laboratory can be better explained with these model theories than by the time-average relation. A study of a general character, not depending a priori on a special model of the porous structure, was still lacking.

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By J. A. Musselman, P. F. Gnirk

A study was made of indexed penetrations by a single dull bit tooth under statically applied loads into rock subjected to confining pressures from atmospheric to 5,000 p.si and atmospheric pore pressure. Experimental results obtained with a 45" wedge tooth over the above range of pressures are presented for two limestones and a sandstone, a variely of indexing distances and two degrees of tooth dullness. The optimum distance between successive bit-tooth penetrations required for maximum rock damage and chip formation decreases substantially with increa.sing confining pressure above the brittle-to-ductile transition pressure of a particular rock. However, the distance remains approximately constant for a variation in confining pressure below the transition pressure. At a given confining pressure, the bit-tooth force required lor chip formation is constant for indexing distances greater than optimum, but generally decreases linearly with decreasing indexing distance for distances less than optimum. The chip-formation force data obtained at confining pressures for which the chip-generation mechanism is macroscopic-ally of a pseudoplastic nature compare favorably with previous theoretical results for indexed dull hit-tooth penetrntion into an idealized, rigid, perfectly plastic rock. INTRODUCTION To study the cutting action of a roller-cone bit, the interaction of a penetrating bit tooth with craters formed in a rock surfacc by the passage of previous bit teeth must be considered. Current knowledge of the basic mechanics of bit tooth-rock intcract:on under simulated borehole environmental conditions has been extensively reviewed.',' Particularly of current interest are the effects of bit-tooth shape, distance between successive penetrations and differential pressure at the rock surface on the extent of the interaction. Pertinent to this paper are results of an experimental investigationb f the interaction between successive penetrations by sharp, wedge-shaped bit teeth. It was demonstrated that both bit-tooth angle and differential pressure influence the extent of rock damage between successive bit-tooth penetrations. Specifically, the optimum or minimum distance between successive penetrations required for maximum interact'on or chip generation tends to decrease with decreasing bit-tooth angle and increasing differential pressure. In addition, at differential pressures on the order of 2,000 psi for four va- rieties of limestones and sandstones, the macroscopic mechanism of chip formation exhibits a transition from brittle to ductile. In this paper, experimental consideration is given to successive or indexed penetrat ons by wedge-shaped bit teeth. Since pore pressure in a rock sample is maintained at atmospheric pressure, the differential pressure at the fluid-rock interface is equal to the confining pressure. The degrees of bit-tooth dullness include teeth with flat and round apexes (Fig. 1). Of primary concern in this paper are the bit-tooth forces required for chip formation, the macroscopic mechanism of chip formation and the minimum distance between successive penetrations, i.e., optimum indexing distance required for maximum rock damage, as functions of differential pressure. Of further interest is a comparison of actual bit-tooth chip formation forces at elevated differential pressures with calculated forces from previous theoretical results4 for indexed dull bit tooth penetration into a rigid-plastic rock. EXPERIMENTAL APPARATUS AND PROCEDURE The experimental apparatus consists of a pressure vessel equipped with a piston through the side of the vessel (Fig. 2). A single bit tooth inserted in the lower end of the piston is forced at a desired rate into the rock when the ram pressure chamber is pressurized. Electrical instrumentation incorporated into the apparatus yields a graphical plot of force on the piston as a function of bit-tooth penetration or displacement into the rock. Since the piston and ram assembly are in force equilibrium for a constant confining pressure in the main vessel, the fluid volume in the vessel remains constant during bit-tooth penetration. Hence, the force resisting penetration of the tooth is independent of the force exerted on either end of the as-

By J. Lindbo, B. Vigeholm

IN transmission electron microscopy, specimen thicknesses quoted are frequently based upon either traditionally familiar values or a few evaluations representing the whole material. Taking aluminum in 100 kv TEM as an example, average and maximum values are widely accepted as being 2000 to 2500 and 6000 to 7OOOÅ, respectively. It is the purpose of this note to revise these figures and to point out the importance of evaluating individual specimens carefully. All evaluations have been based upon slip trace widths and lattice orientations as determined from diffraction patterns. In many cases where two or more slip systems have been operating the geometrical method described by Crocker and Bevis1 has been applied as a check. The foils were usually oriented to within 2 deg from the exact Bragg angle. Kikuchi patterns were used as indications of correct orientations but not applied in the evaluations. The tilt of the foil surface relative to the beam normal may with certain geometrical relations between the tilt axis and the operating slip plane lead to substantial errors.2'3 Where these geometries were inevitable the samples were omitted in the investigations. Various measures were taken in order to overcome ambiguities, e.g., comparison with neighboring grains, tilts, evaluations based upon two or three slip systems,' and comparison with extinction contour evaluations where s = 0 conditions were obtained. Errors caused by misinterpretation of the slip traces on a micrograph are easily avoided by considering the bright-dark sequence on opposite surfaces and by taking into account the tapering of the foil usually leading to a distinguishable divergence of the pair of traces. In the investigations described here the interpretation was further facilitated as the slip trace formation was observed on the microscope screen and sketches taken down. In a few observations slipping was so violent that the distinction of pairs was considered dubious and consequently given up. To assess average values, thickness evaluations carried out in two independent investigations were analyzed: I) 99.998 pct A1 extruded, cold-drawn, and recrys-tallized to grain sizes between 35 and 500 um were deformed in tension at room temperature. In order to determine the dislocation densities as a function of strain,4 specimens prepared by spark machining and electropolishing in a PTFE holder were analyzed in the electron microscope at 100 kv. Thicknesses were evaluated for 569 selected areas. Histogram I in Fig. 1 shows the results, the average thickness being 4900Å. II) Electropolished specimens prepared from 99.9999 pct A1 with magnesium contents from 0.005 to 0.5 pct rolled to foil and annealed were subjected to fission fragment irradiationa2 For volumetric dose and defect concentration determinations thickness evaluations were performed on 123 areas. Histogram II in Fig. 1 shows the thicknesses of these areas averaging 4250Å. Whereas in investigation I no selection related to thickness has been made, some thin as well as thick areas have been omitted from I1 for experimental reasons. This and the application of two different microscopes although of the same type may account for the difference in average thickness. Assuming a mean error of 10 pct for a single evaluation, the error of the average should be negligible. In order to investigate the maximum transmissible foil thickness in aluminum, specimens were prepared from single crystals with (111) and (110) orientations parallel to the beam, and from polycrystalline material. Maximum values of thickness that could be measured were given by the stopping of the dislocations. The visibility often extended far beyond the end of the slip trace, but with no means of knowing the

Jan 1, 1970

By C. C. Templeton, S. S. Rushing

Methods previously developed for the study of air-liquid displacements in microscopic capillaries (inner diameters of 3 to 40 microns) have been used to investigate oil-water displacements in capillaries initially filled with water. Displacement calculations assuming perfect displacement and no capillary pressure hysteresis yielded oil effective viscosities smaller than the macroscopic viscosities. For a given liquid pair, the oil effective viscosity decreased both with decreasing capillary size and with increasing oil-water viscosity ratio. This behavior can be explained by the existence of an annular water film (20 A to 260 A thick) on the capillary wall. When the capillary was first filled with oil, the ratio of the oil effective viscosity to the normal oil vircosity was highest for the first water displacement and decreased with subsequent displacements. Sometimes the oil effective viscosity ratio during the initial water displacement was greater than unity. INTRODUCTION In a previous paper1 a technique was described for studying air-liquid and liquid-liquid displacements in very small capillaries of uniform diameter, in the hope that such microscopic data would further the understanding of the nature of multiphase fluid flow through porous media. That paper contained comprehensive data for air-liquid displacements in Pyrex capillaries, with a few data for oil-water displacements in capillaries initially filled with water. The purpose of this paper is to present more complete results for oil-water displacements in capillaries initially filled with water, and to describe for the first time such observations in capillaries initially filled with oil. In this way the effect of the wetting history of the system upon the displacement process may be studied. METHODS The basic techniques employed were described in the previous paper.1 The measuring procedure and the working equations will be briefly summarized here and a few modilications will be pointed out. For the present study, temperature control within 0.l °C was obtained by placing the microscope and its immediate accessories in a thermostated air bath made of a steel frame covered with plexiglas. The water and oils used in this work were the same as in the previous paper,1 with the addition of "Medium Mineral Oil, U.S.P. supplied by the Harshaw Scientific Co. When the first liquid was introduced into the horizontal capillary, the air-liquid static capillary pressure Poc was measured along the observable length of the capillary. From the relation Poc = 4y cos 0/d, the capillary diameter d could be calculated from Poc if the "microscopic" air-liquid boundary tension, To = y cos On, was taken as equal to its known "macroscopic" value. This calculation involves assuming that cos 6 = 1 and that capillary size or the resulting high interfa-cial curvature has no effect on surface tension, or y cos 6, as was verified by our work, and also by that of Cohan and Meyers on air-liquid-solid systems. For several capillaries these calculated diameter values were compared with values measured visually with a filar micrometer eyepiece. For a given capillary the average values for the two methods agreed within 1 or 2 per cent, but the visual values were less reproducible than the calculated values. Further the calculated values were much less subject to personal bias and took into account any slight ellipticity that might be present. Hence diameters calculated from air-liquid Poc data were used throughout this paper. The second liquid was introduced in such a way that a single spherical interface separated the two liquids. Displacements were always made with a constant pressure, Pt, between the ends of the capillary. The times (t) at which the interface passed certain

Jan 1, 1957

By L. Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope' at the supports (Fig. 1). Essentially this assumes:5* ?A = ?, = ?b and dA = dB = 0. However, a host of conditions can cause differential sag or deflection at one support, and even an apparently trivial deviation can have major consequences in the beam: variations in spacing, size, and material of supports; local settlement due to floor heaving or lower mine openings; non-uniformity in wedging or bolt tensioning.8 In one particular instance concrete pillars, poured in place, shrank away from the roof upon setting.' When understood and controlled, differential sag becomes a definite advantage, permitting the transfer of loads from one support to another. Where one support is a bolt or prop and the other a pillar or rib, the load on the former can be reduced while the load on the pillar or rib is increased. This means two things: 1) savings can be effected by using smaller artificial supports such as props and bolts and 2) loads can be increased in the rib to induce eventual failure for longwall caving. In this last respect, another factor underlying coal bumps becomes understandable. The design of a mine roof by beam theory assumes that when a bedded formation is homogeneous, iso-tropic, and elastic, it will act like a uniformly loaded beam, fixed or clamped at both ends,6 s in Fig. 1.'" These are important assumptions. The uniform load is the weight of the beam itself or its body load. For a beam of unit width, this load becomes per foot: w = yhb. w = uniform load y = specific weight, lb per ft3 h = depth or thickness of beam, ft b = width of beam, ft Since b = 1, w - yh [ 1 ] A beam fixed at both supports is statically indeterminate to the second degree, that is, two equations in addition to those for static equilibrium are required to determine the reactions at the supports. These equations result from the geometry. From statistics: ^F,= 0;RA + RB — wL = 0 [2] wU S,M0 = 0 ; MB H------------MA — RBL = 0 [3] it Using superposition in which the left support is kept intact and the right one resolved into an active force and moment, we obtain from Fig. 2:" ?b = ?m + ? b2 + ?B3 = 0 dB = dB1 + dB2 + dB3 / wU Ma RBL \ V d°=(-r+-2—r)-zr [5] Where: Subscripts refer to position on axis of beam R = force, lb M = moment, ft-lb w = uniformly distributed load, lb per ft L = span, ft 0 = slope, radians d = deflection, ft E = Young's Modulus, lb per ft" 1 = Moment of inertia about the neutral axis, ft4 Solving Eqs. 2 through 5 for the four unknown reactions, we obtain: 2 L3 Fig. 3 is obtained by plotting MA and M, vs d, and then plotting RA and R, vs d, and adjusting their scales to coincide with MA and M, vs d,. It should be noted in Eqs. 6 and 7 that as dB increases, MA increases the same amount that Mn decreases. Eqs. 8 and 9 show a similar relationship between RA and R,. Proof that MA is the maximum absolute moment occurring in the beam is as follows: where M, = moment at x wx-When where M,., = maximum positive moment Eqs. 6 and 8 into above: For small dn: MA> M,,,

Jan 1, 1960

By Ronald J. McGregor, Anton R. Hendriksz

INTRODUCTION The NIMCIX contactor was developed in the late sixties at the National Institute for Metallurgy in South Africa, for the main purpose of extracting uraniuy from relatively low-grade uranium solutions. ' The concept was sufficiently developed by 1974 to permit the operation of a 1500 litre per minute column to treat unclarified urgnium-bearing solution under industrial conditions. The plant operated so successfully that several large-scale units have subsequent18 teen constructed and are operating efficiently. ' Total resin consumption figures as210w as 3 per cent per annum have been reported, and the extraction efficiencies of the installations have been exceptionally good. All the solutions treated have been acidic in nature and in every case have been of such a nature as to significantly depress the maximum uranium loading on the resin beads. The chemical constituents of the leach solution fed to the loading column determines the ease with which the soluble uranium can be absorbed by an ion exchange resin. The concentration of competing ions and various resin foulants define the nature of the continuous ion exchange equipment required for efficient extraction performance. The basic NIMCIX concept is retained in these various alternate designs, but batch or continuous elution methods with fully automated or manual control systems may be selected for the different process solution conditions. BRIEF DESCRIPTION OF THE NIMCIX CONTACTOR The NIMCIX ion exchange column is a multi-stage fluidized bed contactor which is designed to permit a counter-current flow of solution and resin in order to maximize extraction efficiency. The flow o resin is periodic, based on the Cloete and Streat 5 principle of reverse flow. The basic operating cycle can be divided into five periods, as illustrated in Figure 1. For the purposes of describing the cycle, the loading column is considered; how- ever, a similar sequence may be applied to the operation of a NIMCIX continuous elution column. S'I'EP 1: During the forward flow period, Solution flows up through the column and fluidizes the resin contained in each stage. The uranium depleted solution overflows the upper flared-section of the column as the tail solution. Step 2: The flow of solution to the column is temporarily stopped and the resin is allowed to Settle onto the plates in the column. STEP 3: During the reverse flow period, a fixed volume of solution is drained from the column to the transfer vessel. This flow causes resin transfer to occur from stage to stage and also out of the bottom stage. At the end of this period, which expires when the low level switch (LS) is actuated, some of the resin is left in the conical section of the column and the pipe interconnecting the column and the vessel. STEP 4: The cone flush period ensures that all the resin left in the cone of the column and the pipe is transferred to the transfer vessel before forward flow commences. STEP 5: The loaded resin in the transfer vessel, which has been isolated from the column, can either be hydraulically transferred to the top of the elution column or eluted in the vessel before being transferred to the top of the loading column. The major advantages associated with the NIMCIX concept are: (i) Simple method of operation (ii) Contactor can readily be scaled up to large diameters. (iii) Because the resin does not pass through pumps or airlifts, and valves cannot be closed on resin beads at any time, the resin losses are exceptionally low. (iv) Operating costs are low. (v) Relatively few valves in the system. (vi) Stable operation is achieved over a wide range of feed rates and concentrations.

Jan 1, 1980