Search Documents

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By William Y. Holland, Roger M. Cook

In view of the increasingly widespread deterioration of concrete structures as the result of the interaction of the alkalies sodium and potassium released by hydration of portland cement and susceptible rocks and minerals in aggregates, it is believed that a paper summarizing the geographic distribution of these aggregates will be of interest to producers and users of concrete, concrete products, and concrete-making materials. THIS paper reviews the problem of alkali-aggre-gate reaction in concrete and describes the geologic and geographic occurrence and distribution of alkali-reactive sand and gravel in western United States. It includes no discussion of crushed stone or synthetic aggregates. Most deposits of sand and gravel are accumulations of particles of rocks and minerals from a variety of sources, and it is not unusual for at least one or two varieties of the rocks to contain some form of reactive material. Examination by petro-graphic methods of many sands and gravels, as well as manufactured aggregates, has shown that a comparatively high proportion of the deposits does contain, in greater or lesser degree, rocks and minerals known to be deleteriously reactive with the alkalies of cement. Fortunately the amount of reactive materials is commonly less than that necessary to cause deleterious effects in concrete. As investigation of unsound concrete structures progresses, it becomes evident that the alkali-aggre-gate reaction is even more widespread than supposed, Figs. 1 and 2. Even though some parts of the country appear at present to be immune, further investigations will probably show that the effects of alkali-aggregate reaction can be seen in many structures in these areas, although only on a small scale in most of them. Many concrete structures will, of course, have lived their useful life before disintegration from this cause is serious, and in others the alkali-aggregate reaction may never become significant even though the microscopic evidence of reaction is present. The alkali-aggregate reaction first was reported to be a cause of deterioration of concrete in 1940 when Stanton1 described expansion of concrete pavements in California. Similar expansion and deterioration of concrete was recognized during succeeding years in concrete structures located in many parts of the country, but particularly in the western states. A number of concrete laboratories2 became interested in the problem. It was soon determined that only certain combinations of aggregate and cement caused the alkali-aggregate reaction to take place, and moreover that the reaction progresses only in the presence of water. Further research proved that cements containing more than 0.60 pct total alkalies (pct Na,O + 0.658 x pct K2O), when used with aggregates containing appreciable amounts of reactive ingredients, caused the reaction to take place, usually with subsequent deterioration of the concrete. During the last few years this limitation has been adhered to in both government and private construction as the maximum allowable alkali content of cement to be used with aggregates of known alkali reactivity. Because of this limitation, it appears that deleterious reaction either has been reduced or eliminated in many recently built structures in which it probably would otherwise have occurred. Recent tests have shown that the degree of expansion obtained with any particular cement-aggre-gate combination depends not only on the alkali content of the cement but also upon the relation of this alkali content to the amount and degree of reactivity of reactive constituents in the aggregate.' In laboratory mortar bars, opal and cements with alkali content of as low as 0.2 pct (as equivalent of Na2O) have produced deleterious expansion as the result of alkali-aggregate reaction. These experiments demonstrate that aggregates containing even 0.1 pct of opal are deleteriously reactive. It was soon determined that alkali-silica gels were formed by the interaction of the alkalies of the cement and the reactive aggregate, Figs. 3 and 4. Osmotic or swelling pressures produced by the continued hydration of these gels cause expansion of the concrete with resulting cracking, warping, and dislocation. Evidence of the alkali-aggregate reaction can be seen by a petrographic study of the deteriorated concrete. Among the first structures studied by this method was Parker Dam on the Colorado River, California-Arizona. In the concrete from this dam pebbles of rhyolite, andesite, siliceous limestone, and chalcedonic chert were found to be reactive.

Jan 1, 1954

By G. S. Tint, M. Herman, V. V. Damiano

Dislocation arrays and substructures were studied in cadmium doped zinc crystals using a newly devised etching technique. Cadmium precipitates delineating the dislocations were revealed by etching a surface closely parallel to the (0001) slip plane. Cinephotomicrography of the continuous etching process revealed the three-dimensional aspects of dislocations in the bulk crystal. Dislocation etch patterns were studied in both deformed and annealed crystals after suitable aging at room temperature. The effect of annealing was evidenced by a rearrangement of the dislocations into low-angle boundaries and hexagonal networks. ETCH pit techniques have been used extensively to study dislocations in both deformed and annealed bulk metal crystals. Ideally one hopes to obtain a one-to-one correspondence between the etch pits and the points of emergence of the dislocations at the surface. One then attempts to deduce the way in which dislocations are arranged in the bulk crystal from the arrangement of etch pits on the surface. It is clear that one can obtain only limited information of the dislocation configurations inside the crystal from etch pit studies of single surfaces. Considerably more information is obtained if one is able to follow the course of the dislocations through the crystal using progressive etching technique. Techniques of this sort were used by Gilmanl to study dislocations on the slip planes of NaCl crystals and by Damiano and Tint2 to study dislocation arrangement in zinc crystals grown from the melt. The present paper makes use of a technique first described by Tint and Damiano3 to observe and continuously record the dislocation structures which appear while a crystal surface was being progressively etched. Studies were made on cleaved (0001) surfaces to reveal the dislocations along their length on the surface closely parallel to the slip plane. The technique for revealing segments of dislocations along their length by etching is well known. Wilsdorf and Kuhlmann-wilsdorf4 revealed disloca- tions along their length in aluminum containing a few percent copper, when precipitates segregated along the dislocations. The technique was used by Low and Guard5 to study dislocation configurations on the slip plane in Fe-Si alloys containing carbon. In the present work the technique was applied to zinc containing cadmium since it was shown by Gil-man6 that a cadmium-rich phase could be made to precipitate from supersaturated solutions along dislocations in zinc. Segments of dislocations delineated by the precipitates were revealed by etching a surface prepared by cleaving the crystal. The three-dimensional nature of dislocations and substructures was thus studied from the cinephotomicro-graphic record of the continuous etching process. EXPERIMENTAL Single crystals of zinc containing the order of 0.1 pct Cd were prepared by slowly lowering a graphite crucible containing the melt through a temperature gradient of 15°C per cm at a rate of 1.5 X 10-3 cm per sec. "As grown" crystals were aged for periods of 1 month at room temperature, then cleaved in liquid nitrogen, and etched according to the procedure used by Gilman.' The etchant containing 32 g of CrO3, 6 g of hydrated Na2SO3 in 100 ml of water behaved as a chemical polish for zinc and etch pits were produced at the site of precipitates or inclusions. After the precipitates or inclusions were removed from the surface, the etch pits left behind were eventually polished smooth. This behavior enabled one to continuously observe the surface while the specimen was immersed in the etchant. Best results were obtained when the specimen surface was vertical and the reaction products of polishing were continuously removed by gravitational convection. Some crystals were heavily deformed in excess of 25 pct strain, others were lightly deformed the order of a few pct by compression such that the deformation occurred essentially by basal glide. Some crystals were etched immediately after deformation, others were allowed to age at room temperature for several weeks prior to etching. Heavily deformed crystals were annealed at various temperatures and etched on the cleavage plane immediately after annealing, others were allowed to age at room temperature for several weeks prior to etching. The etched structures of deformed and annealed structures were studied. Similar experiments were conducted on 99.9999 pct pure zone refined Tadanac zinc crystals which

Jan 1, 1963

By Michael Hoch, Walter C. Wyder

The Cr-Ni system was investigated between 900" and 1400°C and 45 to 100 wt pct Cr. The Cr-Fe system was studied between 1200" and 1385°C and 70 to 100 wt pct Cr. Powdered alloy compacts were produced from high-purity chromium, nickel, and iron poulders. The compacts were sintered in an argon atmosphere and then machined into small, 0.030-in. diam cylindrical specimens. These were then heated by induction in the high-temperature X-ray diJfractwn camem under a helium atmosphere and irradiated with copper Ka radiation. From the results of the high-temperature X-ray diffraction patterns it can be concluded that chromium exists only in the bcc form, and that no eutectoid reaction occurs in the Cr-Ni system in the temperature interval 900" to 1400°C. The X-ray diffraction patterns are in agreement with the Cr-Ni phase diagram of Bechtoldt and Vacher, and Williams. It is possible that chromium undergoes one or more allotropic transformations between room temperature and its melting point. Most of the evidence was gathered from the study of the chromium-rich ends of the Cr-Ni and Cr-Fe binary systems. All the investigations rely heavily on indirect methods: thermal analysis, electrical resistivity, and micro-graphic inspection of quenched samples. In the present work the chromium-rich side of the Cr-Ni and Cr-Fe binary systems is studied, using high-temperature X-ray diffraction techniques. Thus the coexistent structures can be observed directly at temperature. PREVIOUS INVESTIGATIONS ~ansenl shows two possible Cr-Ni phase diagrams 1) a simple eutectic [Liquid =a-Cr(bcc) + y-Ni(fcc)], 2) a eutectic [Liquid+ P-Cr(fcc) + y-Ni(fcc)] and euctectoid [p-Cr(fcc) ==a-Cr(bcc) + yNi(fcc)]. The latter is based on the work of Grant and co-workers.2 Stein and rant'" placed the eutectoid composition at 1215°C and 68 wt pct Cr; their diagram is shown in Fig. l. Similarly, Sully3 also discusses the two proposed diagrams. Price and Grant,4 working on an isothermal section of the Cr-Ni- Fe ternary diagram at 1300°C, made no mention of a ß-chromium phase (fcc). The ß-chromium structure was also reported by Misencik 5 in the Cr-Nb(Cb) system. Williams 6 studied the Cr-Ni system using precipitation techniques. His work included the chromium and nickel solvus lines below 1250°C. He reported no ß structure nor any eutectoid reaction. The solvus lines which he produced were very similar to those of Jette, et al 7 below 1000°C. He concluded that Grant and coworkers2 had misinterpreted their data, and that effects which they had reported were actually due to the rapid and extensive precipitation of the nickel-rich phase. Bechtoldt and vacher8 used sintered powdered alloy compacts in an attempt to find the ß phase. They used metallographic and room-temperature X-ray diffraction techniques and also failed to detect the fcc chromium phase. They attributed the low slope of the chromium solvus at approximately 1150°C as the probable cause of the abundant precipitation obtained. They also stated that the precipitation was the probable cause for the abrupt discontinuities in the thermal analysis and electrical resistivity data which led to the conclusion that a eutectoid reaction existed. Fig. 1 also shows their diagram. Grigor'ev and coworkers9 investigated the polymorphic changes of chromium in the Cr-Ni phase diagram. Using standard microstructural and thermal analysis techniques, they published a phase diagram which contained five polymorphic forms of pure chromium and four eutectoid reactions. They stated that the room-temperature bcc chromium transformed to a fcc structure at 930°C, to bcc at 1300°C, to hcp at 1650oC, and then finally to bcc at 1830°C. The eutectoid reactions were placed at 850°, 960o, 1140°, and 1220°C. Also to be noted was the fact that the uppermost phase, the bcc above 1830°C, was different from the upper phase of Grant and coworkers,2 the fcc above 1840°C. Their eutectoid reactions, temperatures and compositions fall

Jan 1, 1963

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.' Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method' was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.' Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By Marshall Pease, R. J. Brandon

A UTILITY that has a large consumption of coal must insure an adequate and sound supply of fuel. The Detroit Edison Co., which has an annual coal consumption of about four million tons and spends approximately $32 million a year for coal, including freight charges, has developed a program for fuel procurement and for evaluation and selection of fuel for reliable and efficient plant operation. Fuel Procurement Coal Purchasing Division: The Fuel Supply Div. of the Purchasing Dept. combines all of the procurement functions in one group, which must maintain adequate stocks of fuel. In addition to its usual purchasing duties, the division also governs transportation, follow-up, invoice and freight bill, in cooperation with the Accounting Dept. The Fuel Div. is comprised of the fuel agent, an assistant fuel agent, a coal buyer and five coal clerks, who follow the movement of each car, initially approve freight bills and invoices, and file claims whenever there is a shortage of one ton or more. The fuel agent reports directly to the purchasing agent of the Company, and all major programs are planned jointly with the chief purchasing officer. The apparent individuality of the fuel section is necessary because of the tremendous volume of coal cars handled each day, sometimes as many as 500, which must be handled promptly to complete the fastest possible move from the mines to the plants. Determining Annual Coal Volume: Through the combined studies of a Production Dept. Load Committee and the Controller's office, accurate predictions of coal requirements for any given year are provided the Fuel Dept. from 12 to 15 months in advance. This is divided into the requirements of all individual power plants and central heating plants. This in turn determines the quantity and quality for plants whose specific fuels vary with the type of equipment installed. In the Detroit area, which has a high industrial load, early estimates of annual coal consumption usually are resolved at the end of the year within 4 or 5 pct of the original plan. Operating in a highly developed industrial area eases the task of estimating primary output; and, with the residential demands increasing in a steady and fairly well-defined pattern, the overall coal schedules are not subject to radical changes during any given year. Selecting Suppliers: At any time, but especially during or before an emergency, the coal supply factor must be made secure. This is particularly true in the procurement of utility fuel. There are always extreme quantities of so-called "bargain" coal available during the buyers' markets, such as recently prevailed. These opportunistic offerings may be considered a means of averaging down overall price, rather than as a steady and dependable supply source. Coal is purchased on contract from mine operators and sales agents who have proved reliable. They are not opportunists who desert for higher dollars in times of duress; they do not fail to fulfill contracts when markets rise or overship when markets dip. The progressive operator today who is willing to expend capital to improve quality and service deserves much more consideration than a matching of short-term pennies. When a company has a high volume of annual needs, all phases of the mine supply must be considered. The mine must be able to produce the quality required at a fair price and be able to sell oversizes of coal in enough volume to screen sufficient nut and slack. It must crush coal and sell mine run at prices in line with competitive nut and slack and be willing to do so when there is no demand for prepared sizes. Determining Price: The public utility is in direct competition with any of its customers who can, if savings are guaranteed, generate their own power. Today, to a greater extent than ever before, private industry must do a better overall job than Government-controlled operations. The price of coal must be realistically balanced with the price paid by almost all industries and the railroads as well. The supply-demand ratio in coal is not difficult to discern. There is access at all times to Govern-

Jan 1, 1952

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-'. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.' The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,' P. H. Keck,' and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By A. V. Bradshaw, R. I. L. Guthrie

The behavior of large bubbles in the size range 4 to 25 cm3, rising through molten silver, has been studied. It was found that rising velocities were equivalent to those in aqueous systems of low viscosity. Mass transfer coefficients for oxygen bubbles dissolving in silver were found to be 0.036 ± 0.007 cm sec-1, being close to those predicted for transfer through the front surface of the spherical cap bubble only. It is suggested that the surface active nature of oxygen in silver could account for the relatively low coefficients obtained. MANY metallurgical processes involve interactions between gas bubbles and liquids. Examples include the removal of carbon monoxide in Open Hearth Steelmak-ing, the removal of sulfur by blowing air through copper matte during converting, and the removal of hydrogen from steel during vacuum degassing or inert gas flushing. The steps involved in such refining processes include; transport of the dissolved species to the bubble interface, adsorption and chemical reaction of the species at the interface, desorption of product molecules from the interface, and transport of product gas into the bulk gas phase of the bubble. It has been concluded1 that all the interfacial steps involved proceed so rapidly at steelmaking temperatures that transport of the solutes, present in the metal, become the important rate controlling factors provided nucleation phenomena are not restrictive. The O-Ag system was chosen for the investigation into gas bubble-molten metal interactions due to the relatively high solubility of oxygen that enables rates of oxygen transfer to be measured from changes in bubble volume. Other advantages of this system include the absence of a stable oxide phase at an oxygen pressure of 1 atm and the relatively low melting point of the metal which permits the use of a metallic container, providing that it is resistant to oxidation. In those metallurgical processes where bubbles have an important influence, bubble volumes are usually greater than 5 cm3. For this reason the present study relates specifically to single large bubbles of oxygen rising in silver. These bubbles adopt the characteristic spherical cap shape similar to that shown in Fig. 1 for a 30 cc bubble rising in water. After an initial investigation to determine the velocities of inert (nitrogen) bubbles rising in molten silver, experiments were carried out with oxygen and the rates of mass transfer between the oxygen bubbles and the silver were measured. EXPERIMENTAL Apparatus. The apparatus, Fig. 2, for containing molten silver, was constructed from "Nimonic 75" Alloy (75 pet Ni, 20 pet Cr, 5 pet Fe, Mn) and provided for the release of single bubbles from an hemispherical cup, situated at the bottom of the column. The cup was turned by translating the rotation of the drive shaft through 90 deg. This was accomplished by the use of a bevelled gear system, and a smooth drive was provided by the lubricating action of the silver on the gears. Since reliable high temperature seals at 1000°C were found to be impracticable, the filling and drive shaft tubes were extended outside the 3.5 kw resistance wire tube furnace, where connections were made using easily accessible O-ring seals. The apparatus remained gas tight to the atmosphere at pressure differentials far in excess of those used. The filling tube was connected via a small bore tube to the differential pressure transducer. Gas could be bubbled into the inverted cup from two i-in. tubes which passed down the inside of the column to preheat the gas. The temperature of the silver was maintained at 1020°C during all experiments. Measurement of Bubble Volume. In order to calculate mass transfer rates, it was necessary to obtain a continuous record of the bubble's volume during its passage through the column of molten silver. The method adopted for measuring the bubble volume involved closing off the top gas space to the atmosphere prior to each experiment, and recording the variation in gage pressure of this space during the formation and rise of the bubble. Since any change in bubble volume results in an equal change in top space volume, Boyles Gas Law may be applied (for isothermal con-

Jan 1, 1970

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952

By R. E. Reed-Hill, W. H. Hartt

High-purity magnesium single crystals, oriented with basal plane parallel to stress axis, were deformed in tension at room temperature so as to form second-order (1011)- (1012) twins. Investigation by optical and replica electron microscopy revealed that these twins can support very large internal strains approaching 1000 pct and that fracture follows as a direct consequence of these strains. At low strains the basal plane within (10i1)- (10i2) twins rotates with increasing deformation until it becomes approximately parallel to the twin boundaries. This rotation is not consistent with deformation by basal slip in the double twin, but may be rationalized in terms of nonbasal slip. Observations also indicate that basal slip in the primary (1011) twin, prior to second-order twinning, may contribute to this rotation. Deformation markings that are difficult to interpret in terms of slip on previously observed systems were noted in the twin bands. A possible means of rationalizing these markings is to relate them to grain boundary shear. The fracture associated with these twins is thought to initiate by formation of voids at the twin boundaries. These grow into microcracks, with ultimate fracture occurring by tearing of the interconnecting regions. THE significance of deformation and fracture along second-order (10i1)-(10i2) twins in polycrystalline magnesium1-' and many magnesium alloys4 was discussed in a previous paper.5 It was noted that this double twinning mode effectively controls the room-temperature deformation and fracture of magnesium single crystals, oriented with the basal plane parallel to the tensile axis. Reed-Hill and Robertson6 observed that, although these crystals may fracture at a macroscopic strain of less than 1 pct, shear strains up to 1000 pct could occur within (1011)- (10i2) twin bands. They concluded that the fracture was "ductile" and resulted from concentrating the deformation into a very small volume. The present research was undertaken to obtain a better understanding of the deformation and fracture associated with these twins. EXPERIMENTAL TECHNIQUES The experimental procedure involved straining high-purity magnesium single crystals in tension at room temperature. Specimens were oriented so that the applied stress direction was within 2 deg of the [1010] crystal axis. The specimen cross section was rectangular with faces closely parallel to (1210) and (0002). The specimen preparation and testing procedures have been described in detail elsewhere.5 Second-order (1011)- (1072) twins nucleated during straining were studied using optical and replica electron microscopy techniques. For the latter, cellulose acetate-carbon double replicas were employed. Observations were made on the (1210) crystal surface, which is the plane of shear for twins of this type. In addition to the single crystals, some investigations were carried out on longitudinal polycrystalline specimens. These were obtained from high-purity magnesium plate with a texture in which the basal planes of the grains tended to be nearly parallel to the specimen axis. All. polycrystalline specimens were annealed prior to testing in order to produce a coarse grain structure, permitting Laue back-reflection X-ray photographs to be obtained from grains of interest. EXPERIMENTAL RESULTS a) Deformation Within ( 101 l )-( 1072) Twins. Fig. 1 is an optical micrograph demonstrating the extent of the plastic deformation that can occur in (1011)-(10i2) twin bands. Notice at the lower left corner of the photograph the large displacement of the dark band (a polishing step) where it crosses the twins. The shear strain in the twin band at this position was computed to be 700 pct, using the ratio of step width to twin thickness. It was previously shown5 that (1011)- (1012) twin bands are often composed of small, separate twins aligned close to the macroscopic habit plane. Fig. 2 is an electron micrograph from near the upper end of the twin band in Fig. 1. This illustrates that the twin habit often does not coincide exactly with the macroscopic band habit, but may be inclined at a slightly smaller angle to the matrix basal plane. Figs. 3 through 6 are electron micrographs of the twin band in Fig. 2 illustrating successive steps in the development of deformation inside the band. A twin band such

Jan 1, 1969

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe's books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o'clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,'. ' Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By N. K. Chen, R. B. Pond

IN the study of slip band* formation, there have been many examples to show that they do not always appear as lines traversing the entire crystal, but as segments whose ends seem to vanish in their path through the crystal. This characteristic appearance of slip bands has been witnessed under the optical microscope at various magnifications'-' and also under the electron microscope.' A typical example of this behavior seen with the optical microscope is shown in Fig. 1. However, the slip band studies were generally conducted on polished surfaces of single or poly-crystalline metals which had been previously deformed; i.e., the load was generally released so that the observation could be made. Any picture of slip bands so obtained can represent the surface phenomenon only in a static state of the strained material. The conditions prior to their formation cannot be definitely and clearly assigned. Thus, while a segmented slip band may suggest that slip is a growth process as supposed by the theory of the nucleation of slip,V he usual appearance of suddenly and fully developed slip bands around the crystal has generally been considered as a consequence of uniform shear of the entire slip plane akin to a cataclysmic process. Little clear-cut information is available with regard to the speed at which a slip band forms, its direction of motion, the geometry of its position with regard to its neighbors, and its dependence on orientation. A description is given in this paper of experimental apparatus by which the progressive formation of slip bands can be recorded while the specimen is undergoing deformation. Qualitative and quantitative data on the dynamic formation of slip bands will be presented with special interest concerning the propagation of slip bands, the spacing of slip bands, and their relations to strain hardening. Views on the formation of slip bands are discussed and a mechanism of the unit process involved in the formation of a slip band is proposed. Preparation of Specimens Single-crystal specimens of high purity aluminum (99.997 pct), 1/8 in. square in cross-section and 1% in. long in gage length, were made by the method of gradual solidification from the liquid state. Since no machining work could be introduced in preparation of crystals of such small size, a special mold was designed for casting them to final shape. The mold consisted of two, separate, high purity graphite blocks. Generally, 20 molds were packed together in one container so that 20 specimens could be obtained by one casting operation. This was desirable since it was possible by this method to obtain groups of crystals with similar orientations. The as-cast crystals were carefully clipped from the gate, etched, and homogenized for 24 hr at 600°C. They were then very gently polished using a 4/0 paper, re-etched, and finally electrolytically polished after the method previously described by Chen and Mathewson.6 The crystallographic orientations were determined using a back-reflection, Laue method. Tensile Testing and Photographic Method The tensile testing equipment for these tests was composed of a specially designed microtensile machine, microload cell and microclip gage with necessary appurtenances. The members of the microtensile machine consisted of three parts, as shown in Fig. 2. The chassis is equipped with an oil cylinder, A, and piston, the piston being part of the movable cross-head, B. Pressure in the oil cylinder is controlled and regulated by an external pneumatic-hydraulic cell, C, which is connected to the cylinder by a Vs in. high pressure copper tube. This cell is half filled with hydraulic oil and has a needle valve, D, on the oil exit side as well as a needle valve, E, on the gas inlet side. A quick-acting valve, F, as well as a pressure gage is provided for the gas side. The oil exits into the load piston on the microtensile machine. By connecting a tank of inert gas to the gas inlet, regulated pressures were provided over the oil so that the oil would leave the cell at a rate determined by the setting of the exit needle valve, the gas pressure, and the pressure of the oil in the load piston of the microtensile machine. With this pneumatic-hydraulic appurtenance it was possible to

Jan 1, 1953

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955