Search Documents

By D. G. Russell

Two techniques have been developed with which the applicability of pressure build-up analyses can be extended to include pressure data which previously have been considered virtually unusable. One of the interpretation methods makes possible the analysis of pressure build-up performance during the wellbore fill-up or after production period which occurs soon after a well is closed in. The other technique is an extension of a method for analyzing pressure build-up performance during the late-time portion of the pressure build-up which occurs after boundary eflects first begin to alter the shape of a conventional pressure build-up curve. With both of these methods it is possible to obtain estitnates of the kh product, the skin factor and the reservoir pressure. In addition, with the late-time analysis technique it is possible to obtain an estimate of the contributory drainage volume of the well being tested. This means that in some cases a check on reservoir limit test and (or) material-balance calculations can now be obtained from pressure build-ups. Both methods are slightly more time-consuming than conventional pressure build-up analysis methods because trial-and-error plots of pressure data must be made. The late-time method for analysis of pressure build-ups is in principle applicable to the late-time portion of a two-rate flow test or a pressure drawdown test. The interpretation formulas and procedures for these types of tests are also outlined. In these cases, as with pressure build-ups, it is significant that an estimate of the contributory pore volume is also obtained. On the basis of limited experience with the new techniques, it appears that satisfactory estimates of the kh product, skin factor, reservoir pressure and, for late-time analysis, contributory drainage volume can be obtained. INTRODUCTION The analysis of bottom-hole pressure build-up behavior in closed-in wells has been a a subject of interest in petroleum engineering circles for many years. In fact, few other subjects have received as much attention as pressure buildup analysis methods have. The cause for this interest is essentially twofold in nature. First, the pressure behavior of a well can normally be measured with a reasonably high degree of accuracy so that good data for analysis can be obtained. Secondly, over a fairly wide range of operating conditions, valuable information as to the quality of the reservoir rock and completion efficiency of the well can be obtained at a nominal cost. In recent years, numerous papers have been prepared on the effects of various operating conditions and reservoir heterogeneities on pressure buildup behavior. Very little work has been done, however, on extension of pressure build-up analysis methods to those pressure data which are not amenable to analysis by the present methods. The theory upon which the analysis of shut-in bottom-hole pressure build-up data is based is derived from the solution of the radial flow equation for a slightly compressible fluid for constant-rate conditions. It requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed bottom-hole pressure vs log (t + ?t)/ ?t (where At is shut-in time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the formation permeability, the well damage or skin factor, and the reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. The successful application of this procedure depends on being able to recognize the straight-line section on the basic pressure build-up plot. The presently used pressure build-up interpretation theory also assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing-in to the formation. This adjustment period is commonly referred to as the "afterproduction" or "fill-up" portion of the pressure build-up. During the period that the well fill-up effect is most pronounced, the basic pressure build-up plot is nonlinear. At later shut-in times after the effects of a drainage boundary have been felt at the well, deviation from the straight-line behavior of the pressure build-up plot also results. In many cases either of these effects or a combination of both can make the straight-line portion on the pressure build-up plot difficult to recognize. Obviously, an extension of pressure build-up analysis methods to include the afterproduction period and the period in which boundary effects are being felt would be desirable and might render valuable pressure data which for years have been considered virtually unusable. The principal reference of note concerning pressure buildup analysis during the afterproduction period is a paper by Gladfelter, Tracy and Wilsey.1 In the approach of these authors it is necessary to measure the rate of influx into the well during the afterproduction period. This is done through sonic measurements or through measurement of tubing-head and casing-head pressures simultaneously with

Jan 1, 1967

Jan 1, 1951

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By Homer G. Turner

Coals, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal. Technique The method adopted in this investigation is similar to that described in an earlier paper.' Because of slight modifications recently made, the process is again described. It consists, briefly, of etching a polished surface of coal with heat. Although pieces of various sizes and shapes are used, blocks of coal about 2 or 3 cm. square take the most uniform polish and are large enough to be handled with ease. Larger pieces can be used if one has the equipment for polishing them and they rnay be desirable when one wishes to study some particular form that extends for some distance through the coal. Large surfaces, however, require greater care in polishing and etching; for this reason, they are not recommended for ordinary work.

Jan 1, 1925

By Reno H. Sales

Jan 1, 1914

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

By V. K. Zworykin

THROUGHOUT its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes; it. has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron. Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction -at the very best a tenth-of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. To overcome it, a different imaging medium must be employed. The existence of such a medium became evident when it was demonstrated' that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed, Furthermore, although a wave length may be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light: Actually, the electron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. THE ELECTRON MICROSCOPE Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the electrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08 ADACHI, JINZOO 11 Shiba Park, Shiba-ku, Tokyo, Japan. '88 ADAMI, C. J., Min. Engr., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12

Jan 1, 1917

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.'," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young's modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith's well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By Cyril Smith

ALTHOUGH alloys of copper and silicon were examined several years ago,1 and their excellent mechanical properties were shown, it was not until C: B. Jacobs2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass. Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. REVIEW OF PREVIOUS WORK ON, THE BINARY SYSTEMS There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described,3 which indicate that there is a change insolubility with temperature.

Jan 1, 1930

By W. R. Shimer

In his valuable report on Finishing Temperatures and Properties of Rails,l Dr. G. X. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying out the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high percentages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility than rails of identically the same composition and section which were rolled direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 1, 1915