Search Documents

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967

Considerable improvements in diamond drilling equipment have been made since the early 1950s. A recent drilling programme, however, at Williamtown, near Newcastle, carried out by the Joint Coal Board on behalf of the Electricity Commission of New South Wales, emphasized deficiencies in existing equipment when particularly diflkult coring conditions were encountered.Spurred by unacceptably low recoveries in coal seams in this area, the Joint Coal Board devised and developed, with the assistance of the Electricitv Commission, a new typc core lifter and a special 26 ft triple tube core barrel, designed to operate in conjunction with it in bad coring conditions.The core lifter, whieh is propped open clear of incoming core during drilling, is activated by fluid impulses generated inside the core barrel. It can be used with double tube barrels when drilling firm rocks whichdo not change diameter by compaction inside the barrel.Softer rocks. such as clayey types, require the use of a rriple tube barrel.Results from testing carried out to date in difficult areas in New South Wales coalfields have shown that greatly improved results can be obtained with the new equipment. Although developed essentially for coaldrilling, the new core lifter and barrel could be adapted to other fields of diamond drilling. Even in areas where no great coring difficulty is encountered the cost advantage deriving from the greatly inereased life of the core lifter and the adaptor in which it is housed could justify its use.

Jan 1, 1967

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005

By P L. McCarthy

To design and operate a successful mine the technical specialists must agree on what is ore, what is not ore, and how quickly the orebody is to be mined and processed. These seemingly simple questions defy easy analysis and can push mining engineers, geologists, metallurgists and others to the limit of their capabilities. The questions are rarely addressed adequately in feasibility studies or in operational planning. To optimise the mine and processing plant requires proper determination of cut-off grades or values, prediction of feed variability on an hourly, daily or longer basis, right-sizing the mining rate for optimum product quality, understanding the cost of capital and the expectations of investors, and many other considerations that involve geology, geotechnical engineering, mining, metallurgy, environmental effects and economics. This paper addresses the key matters that should be considered as inputs to the practical issues of metallurgical plant design and operation.CITATION:McCarthy, P L, 2015. Integrated mining and metallurgical planning and operation, in Proceedings MetPlant 2015, pp 35–45 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The smelting of the Broken Hill lead concentrates at the Broken Hill Asso,ciated Smelters produced, among other products, approximately 4,900 ounces of gold and 8,800,000 ounces of silver during the year ending June 30th, 1938. The following table shows the actual amounts of gold per ton of lead concentrate produced during this period at the important mines. The total gold in the period is calculated from the number of tons of lead concentrates produced, and by comparison with the production' of silver, shows thatthere is no constant relation between the amounts of gold and silver.The fact that no gold is seen during milling, even when gravity concentrating tables are employed, signifies that the gold does not occur as occasional coarse particles.Further, as the values increase considerably in the flotation slime, it can be inferred that the gold occurs as minute inclusions in one or more of the minerals in the lead concentrates.The four most abundant minerals in the lead concentrate are galena, zinc blende, chalcopyrite, and...

Jan 1, 1940

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

By E Skinner, G Lane

Project delivery strategies are determined by project context, business case requirements, scale of project, market conditions, ownerÆs capability and preference, contractorÆs experience, resource and skill availability, project location and type of project or facility.Successful project management requires the setting of coherent, effective and realistic business objectives and success criteria. The management team needs to lead, prioritise, resource, align, plan, track and communicate the processes that enable the realisation of these business objectives and success criteria.For any given project there is a unique balance between selection of a simple project delivery strategy that minimises interfaces and a complex strategy that necessarily engages the use of expertise and experience from numerous parties. The right balance for a project between these "book-end cases" is a function of how the project owner or managing contractor defines its objectives and chooses to manage risk, cost, schedule and project quality, in the context of the conditions affecting the project.Selection of an effective project delivery strategy requires a detailed appreciation of the range of external and internal environmental / shaping factors which influence the project. These factors include the project constraints imposed by the business, market or operational environments and the selection of an effective mix of primary (head contract), secondary (mix of vertical and horizontal packages) and tertiary (type of individual contract) strategies. The selection of the primary, secondary and tertiary strategies also shapes the project, the size and responsibilities of the ownerÆs team and the framework for delivery of outcomes.How does an owner or prime contractor decide? What is the optimum for a given project? Those with operations management backgrounds will have different views to those with project and construction management backgrounds.Is the simplest practical approach the best approach? Each and every interface needs to be managed.The owner will want a very experienced team that is engaged directly with the owner. The team will have a track record of successfully performing projects using contractors skilled in their respective disciplines and selected using competitive tendering on brilliantly designed scopes of work and good contract terms, with a fully defined project scope and appropriate schedule, for which all significant risks have been addressed and no scope changes are outstanding. Budget and schedule will be expected to have been developed with a full understanding of the scope, situation, risk management requirements etc.The problem is that these conditions rarely exist. The challenge in selection of a project delivery strategy is to resolve how best to address the inadequacies between the ideal case and the present reality. The mechanism for addressing the inadequacies defines the likely outcome of the project.CITATION:Lane, G and Skinner, E, 2013. Project delivery, in Proceedings MetPlant 2013 , pp 50-65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By P To, A Sharp-Paul, S Jones, C Monahan

A key environmental management issue associated with mining projects is tailing disposal. In high rainfall environments this is particularly challenging and generally requires the discharge of excess water from a tailing dam to adjacent streams or coastal waters. Such discharges can potentially have adverse impacts on downstream water quality and the environmental values associated with these waters, such as providing a drinking water supply for local villagers, maintaining a fisheries resource or protecting a fish species of high conservation significance. An alternative to the construction and operation of a conventional tailing dam is Deep Sea Tailing Placement (DSTP). The key features of such a system are:Discharge of the tailing slurry at considerable depth (approximately 120 - 150 m) below the oceanÆs surface. This requires a pipeline to be laid from the process plant to a mix tank, where the tailing is mixed with seawater and entrained air released. The pipeline then continues down the ocean floor to the required discharge depth, which is below the surface mixed layer and the euphotic zone. After discharge, formation of a density current which continues to descend along the ocean floor as long as the slope is sufficiently steep. Final deposition of the tailing in an area where the slope of the ocean floor is insufficient to maintain the density current. This typically occurs at depths of more than 800 m. Water quality issues associated with DSTP include: Impacts on the oceanic water column due to the formation of subsurface plumes which break away from the descending density current. The occurrence of elevated concentrations of contaminants in the interstitial waters of the deposited tailing solids. Fluxes of contaminants from the tailing deposits into the overlying oceanic water column. This paper discusses the water quality aspects of DSTP with particular reference to a case study in Papua New Guinea. The evaluations undertaken as part of the DSTP impact assessment included consideration of both the short- and long-term chemical behaviour of contaminants and bioassays, within the appropriate water quality assessment framework.

Jan 1, 1999

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By McKenzie A. M

The Corridor ore body is so named because it occurs in an east-west zone or corridor of schist bounded on the north by the siliceous conglomerates of Mount Lyell, and on the south by similar conglomerates of the Tharsis ridge (Fig. 1). It was discovered after the geophysical prospecting methods described below had defined a target zone for diamond drilling.Since the proving of copper mineralisation by drilling, the corridor orebody has served the vital function of a convenient known target body for the orientation of more recently developed geophysical methods. Traversing of the orebody by these new methods has provided experience for the evaluation of anomalies elsewhere.Some of the methods applied had not been used in Australia before, and were introduced to the west coast of Tasmania through the undertaking there of modern regional exploration programmes. The authors feel that the information gained could be of assistance to others engaged in geophysical prospecting.HISTORY OF DISCOVERYProspecting in the Mount Lyell district has been more or less continuous since 1881. The first geological report was published by Thureau (1886).In 1934, Blazey and Douglas (1934-38) commenced geophysical surveys at Mt. Lyell using the equipotential method.They obtained anomalous indications in several discrete zones and actually detected the south-east half of the corridor orebody but their work never became the basis for...

Jan 1, 1961

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By D David

Amongst those whose task it is to design tumbling mills and other comminution machines there is an almost religious divide between devotees of the Bond method and devotees of other methods developed in more recent times. For a decade or so the issue was between the Bond power-based methods and the JKMRC (JK) simulation based approach. The newest method to challenge the status quo is power-based and was developed by Steve Morrell. As the title suggests, this paper will take some liberty at concluding that Fred Bond and Steve Morrell may be separated by history, but not by their approaches to their individual contributions to the science of comminution. Another driver for the paper is that although it is good to have diversity of thought, the existing divisions are problematic for those of us signing public disclosure documents. If alternative design methods produce materially different outcomes for the mill duty, then at least one of them is wrong or being used incorrectly. At some point the unsustainable argument may need to be put in a court of law that we metallurgists have two or more materially different design methods, each of which is correct! Therefore, perhaps a resolution is needed before this occurs?The works of both Fred Bond and Steve Morrell are each directly related to their contemporary grinding mill design and operational environments. Both their approaches are empirical, borne of observing and measuring real world situations. Both worked with theories that preceded them, gathered their own data and then each saw shortfalls in the status quo.Fred Bond was an escapee from revolution, a victim of The Great Depression, and had several near death experiences during his early site-based career. Perhaps he was fortuitously rescued from himself when asked by Allis Chalmers (A-C) to set up its rock testing laboratory in Milwaukie in 1930. Fred’s testing led him to conclude that neither the Kick nor the Von Rittinger theories explained his measurements. His writings on the failings of these old theories caused a divide between devotees of the old and new methods at that time. After many years, and much thought and plotting of data (the old way!), he came up with his now-famous equations (and his Third Theory) which have stood the test of time, certainly in the world of Bond-era machines.Coming from England via several African diamond mines, Steve Morrell immersed himself into the comminution world of the JK in Brisbane about a decade after Fred passed on. The JK had developed its semi-autogenous grinding (SAG) simulation framework using its own pendulum breakage tester, itself a derivative of the twin pendulum impact device invented by Bond decades earlier. At the JK Steve developed his authoritative Tumbling Mill Power equations and was involved in real world analysis of comminution problems on the global stage. Steve’s JK experience coincided with the demise of the rod mill, the rise of autogenous grinding (AG) and SAG milling and a rapid expansion in concentrator capacity.Morrell left the JK to pursue his own interests, which included ongoing consulting work, now demanded by the comminution world. He then turned to investigating a growing list of discrepancies between the opinions of designers and theoreticians, and the factual outcomes. The Morrell Method of design arose from this re-examination of ore testing, real world operating data and these glaring and expensive discrepancies between design and outcome. The elements necessary for a relook at the world of rock breakage were in place!CITATION:David, D, 2017. Steve and Fred would have been mates – a comminution design evolution story, in Proceedings MetPlant 2017, pp 2–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

By T Atchison

The Vale Ferro Carajßs S11D project in northern Brazil is based on the movement of unprecedented volumes of waste and ore for mobile in-pit crushing and conveying or ætrucklessÆ systems. In peak years, the system is intended to handle a combined 160 Mt of material.The planning and implementation of the first such system for Vale, in a remote greenfield site, utilising the services of a range of international study, design and supply partners has provided a unique set of technical and project delivery challenges. The lessons from these are of value to the industry as the trend to remote and high-volume operations continues.This paper describes the key features of the mining system and documents the challenges and mitigations for important technical, cultural and project delivery issues that have arisen. It is a combined description of the journey taken by both Vale (as owner) and SKM (as delivery partner) over the course of many years.CITATION:Atchison, T, 2013. Lessons from the S11D truckless mining project, in Proceedings Iron Ore 2013 , pp 177-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A E. Annels, I P. Hodkinson an, S P. Barr

Narrow vein systems represent an important source of gold, which have generally been exploited by small to medium sized companies. Their evaluation poses particular problems because of their grade and geological complexities. The determination of grade is arguably the most important activity in resource estimation, as it is generally grade and not tonnage that makes an orebody. This is particularly true of narrow vein-gold deposits whose resources are generally relatively small, though medium to high-grade (6 - 40+ g/t). They often display extreme grade anisotropy in all directions. Two grade populations are generally observed; 1) low, often subeconomic, background grades and 2) high-grades associated with discrete ore shoots. It is possible for gold to be distributed within the wallrocks as well as within the vein. Extremely high-grade values typify this style of mineralisation and require special consideration during grade estimation to determine if top cutting is valid or not. Estimation of both width and accumulation in 2D on vertical longitudinal projections or inclined planes have historically been used to evaluate narrow veins. Resource estimates based on traditional 2D methods is still widespread, but has in some cases been replaced by computer-based 3D modelling. Grade estimation methods are well-known, ranging from classical to geostatistical. Historically, classical methods such as inverse distance weighting have been used, though geostatistical indicator kriging methods are sometimes applicable. Geostatistical studies are driven by the production of reliable variograms, which in narrow gold veins is often problematic. It is generally difficult to define resources from drillhole intersections beyond the inferred and indicated categories with any confidence. In the majority of cases underground development is required to define measured resources and ore reserves. Trial mining/bulk sampling is often used to test estimated grades and also provides important data on ground conditions and the parameters relating to the proposed mining method required for ore reserve definition. Regular reconciliation should be undertaken between the estimated stope grades, grades indicated from stope/truck sampling and grades realised in the mill in order to determine whether correct evaluation strategies are being applied. The important feature of narrow vein-gold deposits is their strong geological controls; in response to this, geologists must understand the geology as best as possible.

Jan 1, 1999

KIeeman (1968) described practice in the Mount Hebbard dump concentrator, Broken Hill, N.S.W. The purpose of this note is to give data on flotation pulp chemistry in the plant for comparison with results of Woodcock and Jones (1970a, 1970b).Ten chemical parameters were measured at ten points in the circuit using the techniques of Woodcock and Jones (1970a, 1970b). Fig. 1 shows a condensed time plot of some continuous measurements in conditioner overflow and rougher feed. Fig. 2 shows average values of selected parameters at the start and end of each of the three rougher flotation stages.DISCUSSIONpH and redox potentiaIsFig. 1 shows that pH and Eh were relatively constant at the start of sulphide lead flotation. There was a fairly steady increase in pH throughout the circuit (Fig. 2), but flotation was always conducted in a slightly acid pulp in spite of the large amount of alkaline reagents added. Eh values became more positive as the pulp progressed through the circuit (Fig. 2) in accord with results elsewhere.

Jan 1, 1973